u-boot/arch/arm/mach-socfpga/spl_gen5.c
Simon Goldschmidt a89441a74f arm: socfpga: gen5: don't zero bss in board_init_f()
The socfpga gen5 SPL manually zeroed bss in board_init_f(). Now that the
DDR driver does not use bss any more, bss is not used before board_init_r()
and we can remove this hack.

bss is normally zeroed by crt0.S, but after board_init_f(), before
board_init_r(). socfpga just had this double-zeroing because it invalidly
used bss in board_init_f() already (during DDR initialization).

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-08-15 08:50:02 +02:00

149 lines
3.5 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2012 Altera Corporation <www.altera.com>
*/
#include <common.h>
#include <asm/io.h>
#include <asm/u-boot.h>
#include <asm/utils.h>
#include <image.h>
#include <asm/arch/reset_manager.h>
#include <spl.h>
#include <asm/arch/system_manager.h>
#include <asm/arch/freeze_controller.h>
#include <asm/arch/clock_manager.h>
#include <asm/arch/misc.h>
#include <asm/arch/scan_manager.h>
#include <asm/arch/sdram.h>
#include <asm/sections.h>
#include <debug_uart.h>
#include <fdtdec.h>
#include <watchdog.h>
#include <dm/uclass.h>
DECLARE_GLOBAL_DATA_PTR;
static const struct socfpga_system_manager *sysmgr_regs =
(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
u32 spl_boot_device(void)
{
const u32 bsel = readl(&sysmgr_regs->bootinfo);
switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) {
case 0x1: /* FPGA (HPS2FPGA Bridge) */
return BOOT_DEVICE_RAM;
case 0x2: /* NAND Flash (1.8V) */
case 0x3: /* NAND Flash (3.0V) */
return BOOT_DEVICE_NAND;
case 0x4: /* SD/MMC External Transceiver (1.8V) */
case 0x5: /* SD/MMC Internal Transceiver (3.0V) */
return BOOT_DEVICE_MMC1;
case 0x6: /* QSPI Flash (1.8V) */
case 0x7: /* QSPI Flash (3.0V) */
return BOOT_DEVICE_SPI;
default:
printf("Invalid boot device (bsel=%08x)!\n", bsel);
hang();
}
}
#ifdef CONFIG_SPL_MMC_SUPPORT
u32 spl_boot_mode(const u32 boot_device)
{
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
return MMCSD_MODE_FS;
#else
return MMCSD_MODE_RAW;
#endif
}
#endif
void board_init_f(ulong dummy)
{
const struct cm_config *cm_default_cfg = cm_get_default_config();
unsigned long reg;
int ret;
struct udevice *dev;
/*
* First C code to run. Clear fake OCRAM ECC first as SBE
* and DBE might triggered during power on
*/
reg = readl(&sysmgr_regs->eccgrp_ocram);
if (reg & SYSMGR_ECC_OCRAM_SERR)
writel(SYSMGR_ECC_OCRAM_SERR | SYSMGR_ECC_OCRAM_EN,
&sysmgr_regs->eccgrp_ocram);
if (reg & SYSMGR_ECC_OCRAM_DERR)
writel(SYSMGR_ECC_OCRAM_DERR | SYSMGR_ECC_OCRAM_EN,
&sysmgr_regs->eccgrp_ocram);
socfpga_sdram_remap_zero();
socfpga_pl310_clear();
debug("Freezing all I/O banks\n");
/* freeze all IO banks */
sys_mgr_frzctrl_freeze_req();
/* Put everything into reset but L4WD0. */
socfpga_per_reset_all();
if (!socfpga_is_booting_from_fpga()) {
/* Put FPGA bridges into reset too. */
socfpga_bridges_reset(1);
}
socfpga_per_reset(SOCFPGA_RESET(OSC1TIMER0), 0);
timer_init();
debug("Reconfigure Clock Manager\n");
/* reconfigure the PLLs */
if (cm_basic_init(cm_default_cfg))
hang();
/* Enable bootrom to configure IOs. */
sysmgr_config_warmrstcfgio(1);
/* configure the IOCSR / IO buffer settings */
if (scan_mgr_configure_iocsr())
hang();
sysmgr_config_warmrstcfgio(0);
/* configure the pin muxing through system manager */
sysmgr_config_warmrstcfgio(1);
sysmgr_pinmux_init();
sysmgr_config_warmrstcfgio(0);
/* Set bridges handoff value */
socfpga_bridges_set_handoff_regs(true, true, true);
debug("Unfreezing/Thaw all I/O banks\n");
/* unfreeze / thaw all IO banks */
sys_mgr_frzctrl_thaw_req();
#ifdef CONFIG_DEBUG_UART
socfpga_per_reset(SOCFPGA_RESET(UART0), 0);
debug_uart_init();
#endif
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
ret = uclass_get_device(UCLASS_RESET, 0, &dev);
if (ret)
debug("Reset init failed: %d\n", ret);
/* enable console uart printing */
preloader_console_init();
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
hang();
}
}