mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
490753ace3
Instead of allocating space in the driver for the serdes specification table, just allow the board file to set a pointer to it. Also, allow the board to only specify the lanes that are used instead of including unused lanes. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
156 lines
4.5 KiB
C
156 lines
4.5 KiB
C
/*
|
|
* Copyright (C) 2015 Stefan Roese <sr@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
|
|
#include <../serdes/a38x/high_speed_env_spec.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define ETH_PHY_CTRL_REG 0
|
|
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
|
|
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
|
|
|
|
/*
|
|
* Those values and defines are taken from the Marvell U-Boot version
|
|
* "u-boot-2013.01-2014_T3.0"
|
|
*/
|
|
#define DB_GP_88F68XX_GPP_OUT_ENA_LOW \
|
|
(~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \
|
|
BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \
|
|
BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31)))
|
|
#define DB_GP_88F68XX_GPP_OUT_ENA_MID \
|
|
(~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \
|
|
BIT(16) | BIT(17) | BIT(18)))
|
|
|
|
#define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0
|
|
#define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x0
|
|
#define DB_GP_88F68XX_GPP_POL_LOW 0x0
|
|
#define DB_GP_88F68XX_GPP_POL_MID 0x0
|
|
|
|
/* IO expander on Marvell GP board includes e.g. fan enabling */
|
|
struct marvell_io_exp {
|
|
u8 chip;
|
|
u8 addr;
|
|
u8 val;
|
|
};
|
|
|
|
static struct marvell_io_exp io_exp[] = {
|
|
{ 0x20, 6, 0x20 }, /* Configuration registers: Bit on --> Input bits */
|
|
{ 0x20, 7, 0xC3 }, /* Configuration registers: Bit on --> Input bits */
|
|
{ 0x20, 2, 0x1D }, /* Output Data, register#0 */
|
|
{ 0x20, 3, 0x18 }, /* Output Data, register#1 */
|
|
{ 0x21, 6, 0xC3 }, /* Configuration registers: Bit on --> Input bits */
|
|
{ 0x21, 7, 0x31 }, /* Configuration registers: Bit on --> Input bits */
|
|
{ 0x21, 2, 0x08 }, /* Output Data, register#0 */
|
|
{ 0x21, 3, 0xC0 } /* Output Data, register#1 */
|
|
};
|
|
|
|
static struct serdes_map board_serdes_map[] = {
|
|
{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
|
|
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
|
|
};
|
|
|
|
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
|
|
{
|
|
*serdes_map_array = board_serdes_map;
|
|
*count = ARRAY_SIZE(board_serdes_map);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Define the DDR layout / topology here in the board file. This will
|
|
* be used by the DDR3 init code in the SPL U-Boot version to configure
|
|
* the DDR3 controller.
|
|
*/
|
|
static struct hws_topology_map board_topology_map = {
|
|
0x1, /* active interfaces */
|
|
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
|
|
{ { { {0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0} },
|
|
SPEED_BIN_DDR_1866L, /* speed_bin */
|
|
BUS_WIDTH_8, /* memory_width */
|
|
MEM_4G, /* mem_size */
|
|
DDR_FREQ_800, /* frequency */
|
|
0, 0, /* cas_l cas_wl */
|
|
HWS_TEMP_LOW} }, /* temperature */
|
|
5, /* Num Of Bus Per Interface*/
|
|
BUS_MASK_32BIT /* Busses mask */
|
|
};
|
|
|
|
struct hws_topology_map *ddr3_get_topology_map(void)
|
|
{
|
|
/* Return the board topology as defined in the board code */
|
|
return &board_topology_map;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* Configure MPP */
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
|
|
writel(0x11244011, MVEBU_MPP_BASE + 0x08);
|
|
writel(0x22222111, MVEBU_MPP_BASE + 0x0c);
|
|
writel(0x22200002, MVEBU_MPP_BASE + 0x10);
|
|
writel(0x30042022, MVEBU_MPP_BASE + 0x14);
|
|
writel(0x55550555, MVEBU_MPP_BASE + 0x18);
|
|
writel(0x00005550, MVEBU_MPP_BASE + 0x1c);
|
|
|
|
/* Set GPP Out value */
|
|
writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
|
|
writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
|
|
|
|
/* Set GPP Polarity */
|
|
writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
|
|
writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
|
|
|
|
/* Set GPP Out Enable */
|
|
writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
|
|
writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
int i;
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
/* Init I2C IO expanders */
|
|
for (i = 0; i < ARRAY_SIZE(io_exp); i++)
|
|
i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: Marvell DB-88F6820-GP\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
cpu_eth_init(bis); /* Built in controller(s) come first */
|
|
return pci_eth_init(bis);
|
|
}
|