u-boot/board/rockchip/evb_rk3399
Jagan Teki b1fccd3c0c arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.

VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.

So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.

rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.

Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-07 19:45:57 +08:00
..
evb-rk3399.c common: Drop log.h from common header 2020-05-18 21:19:18 -04:00
Kconfig ARM64: rockchip: add support for rk3399 SoC based evb 2016-07-25 20:46:45 -06:00
MAINTAINERS arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support 2020-07-07 19:45:57 +08:00
Makefile ARM64: rockchip: add support for rk3399 SoC based evb 2016-07-25 20:46:45 -06:00
README rockchip: Remove ARCH= references from documentation 2020-06-02 17:27:04 -04:00

Introduction
============

RK3399 key features we might use in U-Boot:
* CPU: ARMv8 64bit Big-Little architecture,
*      Big: dual-core Cortex-A72
*      Little: quad-core Cortex-A53
* IRAM: 200KB
* DRAM: 4GB-128MB dual-channel
* eMMC: support eMMC 5.0/5.1, suport HS400, HS200, DDR50
* SD/MMC: support SD 3.0, MMC 4.51
* USB: USB3.0 type-C port *2 with dwc3 controller
*      USB2.0 EHCI host port *2
* Display: RGB/HDMI/DP/MIPI/EDP

evb key features:
* regulator: pwm regulator for CPU B/L
* PMIC: rk808
* debug console: UART2

In order to support Arm Trust Firmware(ATF), we can use either SPL or
miniloader from rockchip to do:
* do DRAM init
* load and verify ATF image
* load and verify U-Boot image

Here is the step-by-step to boot to U-Boot on rk3399.

Get the Source and prebuild binary
==================================

  > mkdir ~/evb_rk3399
  > cd ~/evb_rk3399
  > git clone https://github.com/ARM-software/arm-trusted-firmware.git
  > git clone https://github.com/rockchip-linux/rkbin.git
  > git clone https://github.com/rockchip-linux/rkdeveloptool.git


Compile ATF
===========

  > cd arm-trusted-firmware
  > make realclean
  > make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 bl31

  Get bl31.elf in this step, copy it to U-Boot root dir:
  > cp build/rk3399/release/bl31/bl31.elf ../u-boot/

  Or you can get the bl31.elf directly from Rockchip:
  > cp rkbin/rk33/rk3399_bl31_v1.00.elf ../u-boot/bl31.elf


Compile U-Boot
==============

  > cd ../u-boot
  > export CROSS_COMPILE=aarch64-linux-gnu-
  > make evb-rk3399_defconfig
  for firefly-rk3399, use below instead:
  > make firefly-rk3399_defconfig
  > make
  > make u-boot.itb

  Get spl/u-boot-spl.bin and u-boot.itb in this step.

Compile rkdeveloptool
=====================

Get rkdeveloptool installed on your Host in this step.

Follow instructions in latest README, example:
  > cd ../rkdeveloptool
  > autoreconf -i
  > ./configure
  > make
  > sudo make install

Both origin binaries and Tool are ready now, choose either option 1 or
option 2 to deploy U-Boot.

Package the image
=================

Package the image for U-Boot SPL(option 1)
--------------------------------
  > cd ..
  > tools/mkimage -n rk3399 -T rksd -d spl/u-boot-spl.bin idbspl.img

  Get idbspl.img in this step.

Package the image for Rockchip miniloader(option 2)
------------------------------------------
  > cd ..
  > cp arm-trusted-firmware/build/rk3399/release/bl31.elf rkbin/rk33
  > ./rkbin/tools/trust_merger rkbin/tools/RK3399TRUST.ini
  > ./rkbin/tools/loaderimage --pack --uboot u-boot/u-boot-dtb.bin uboot.img

  Get trust.img and uboot.img in this step.

Flash the image to eMMC
=======================

Flash the image with U-Boot SPL(option 1)
-------------------------------
Power on(or reset with RESET KEY) with MASKROM KEY preesed, and then:
  > rkdeveloptool db rkbin/rk33/rk3399_loader_v1.08.106.bin
  > rkdeveloptool wl 64 u-boot/idbspl.img
  > rkdeveloptool wl 0x4000 u-boot/u-boot.itb
  > rkdeveloptool rd

Flash the image with Rockchip miniloader(option 2)
----------------------------------------
Power on(or reset with RESET KEY) with MASKROM KEY preesed, and then:
  > rkdeveloptool db rkbin/rk33/rk3399_loader_v1.08.106.bin
  > rkdeveloptool ul rkbin/rk33/rk3399_loader_v1.08.106.bin
  > rkdeveloptool wl 0x4000 u-boot/uboot.img
  > rkdeveloptool wl 0x6000 u-boot/trust.img
  > rkdeveloptool rd

You should be able to get U-Boot log in console/UART2(baurdrate 1500000)
For more detail, please reference to:
http://opensource.rock-chips.com/wiki_Boot_option