mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-28 15:41:40 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
138 lines
3.3 KiB
C
138 lines
3.3 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2017 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
#include <log.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/global_data.h>
|
|
#include "ddr.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#if defined(CONFIG_VID) && (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
|
|
static void fsl_ddr_setup_0v9_volt(memctl_options_t *popts)
|
|
{
|
|
int vdd;
|
|
|
|
vdd = get_core_volt_from_fuse();
|
|
/* Nothing to do for silicons doesn't support VID */
|
|
if (vdd < 0)
|
|
return;
|
|
|
|
if (vdd == 900) {
|
|
popts->ddr_cdr1 |= DDR_CDR1_V0PT9_EN;
|
|
debug("VID: configure DDR to support 900 mV\n");
|
|
}
|
|
}
|
|
#endif
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
ulong ddr_freq;
|
|
|
|
if (ctrl_num > 1) {
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
|
return;
|
|
}
|
|
if (!pdimm->n_ranks)
|
|
return;
|
|
|
|
/*
|
|
* we use identical timing for all slots. If needed, change the code
|
|
* to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
|
|
*/
|
|
pbsp = udimms[0];
|
|
|
|
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
while (pbsp->datarate_mhz_high) {
|
|
if (pbsp->n_ranks == pdimm->n_ranks) {
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
goto found;
|
|
}
|
|
pbsp_highest = pbsp;
|
|
}
|
|
pbsp++;
|
|
}
|
|
|
|
if (pbsp_highest) {
|
|
printf("Error: board specific timing not found for %lu MT/s\n",
|
|
ddr_freq);
|
|
printf("Trying to use the highest speed (%u) parameters\n",
|
|
pbsp_highest->datarate_mhz_high);
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
} else {
|
|
panic("DIMM is not supported by this board");
|
|
}
|
|
found:
|
|
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
|
|
"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
|
|
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
|
|
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
|
|
pbsp->wrlvl_ctl_3);
|
|
|
|
|
|
|
|
popts->half_strength_driver_enable = 0;
|
|
/*
|
|
* Write leveling override
|
|
*/
|
|
popts->wrlvl_override = 1;
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
|
|
/* Enable ZQ calibration */
|
|
popts->zq_en = 1;
|
|
|
|
/* Enable DDR hashing */
|
|
popts->addr_hash = 1;
|
|
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
|
|
#if defined(CONFIG_VID) && (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
|
|
fsl_ddr_setup_0v9_volt(popts);
|
|
#endif
|
|
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
|
|
DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
|
|
}
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
int fsl_initdram(void)
|
|
{
|
|
gd->ram_size = tfa_get_dram_size();
|
|
|
|
if (!gd->ram_size)
|
|
gd->ram_size = fsl_ddr_sdram_size();
|
|
|
|
return 0;
|
|
}
|
|
#else
|
|
int fsl_initdram(void)
|
|
{
|
|
puts("Initializing DDR....using SPD\n");
|
|
|
|
#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
|
|
gd->ram_size = fsl_ddr_sdram_size();
|
|
#else
|
|
gd->ram_size = fsl_ddr_sdram();
|
|
#endif
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_TFABOOT */
|