mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-15 01:17:39 +00:00
750d7ddf2c
Add Serial Download Protocol support as it is a useful method to load flash.bin to RAM and run it via 'uuu'. With this patch, it is possible to start both U-Boot SPL and U-Boot proper using the following 'uuu'command: $ uuu -brun spl flash.bin Based on a patch from Marek Vasut for the imx8mm-mx8menlo board. Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO to reduce its size. Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
150 lines
1.5 KiB
Text
150 lines
1.5 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2019, 2021 NXP
|
|
*/
|
|
|
|
#include "imx8mm-u-boot.dtsi"
|
|
|
|
/ {
|
|
wdt-reboot {
|
|
compatible = "wdt-reboot";
|
|
wdt = <&wdog1>;
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
firmware {
|
|
optee {
|
|
compatible = "linaro,optee-tz";
|
|
method = "smc";
|
|
};
|
|
};
|
|
};
|
|
|
|
&aips4 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
®_usdhc2_vmmc {
|
|
u-boot,off-on-delay-us = <20000>;
|
|
};
|
|
|
|
&pinctrl_reg_usdhc2_vmmc {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2_gpio {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio4 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio5 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&crypto {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&sec_jr0 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&sec_jr1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&sec_jr2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usbmisc1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usbphynop1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usbotg1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc2 {
|
|
u-boot,dm-spl;
|
|
sd-uhs-sdr104;
|
|
sd-uhs-ddr50;
|
|
fsl,signal-voltage-switch-extra-delay-ms = <8>;
|
|
};
|
|
|
|
&usdhc3 {
|
|
u-boot,dm-spl;
|
|
mmc-hs400-1_8v;
|
|
mmc-hs400-enhanced-strobe;
|
|
};
|
|
|
|
&i2c1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators} {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_i2c1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_pmic {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_wdog {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&fec1 {
|
|
phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&wdog1 {
|
|
u-boot,dm-spl;
|
|
};
|