u-boot/board/freescale/m5249evb/m5249evb.c
Becky Bruce 9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00

113 lines
3.2 KiB
C

/*
* (C) Copyright 2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <malloc.h>
#include <asm/immap.h>
/* Prototypes */
int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
int checkboard (void) {
ulong val;
uchar val8;
puts ("Board: ");
puts("Freescale M5249EVB");
val8 = ((uchar)~((uchar)mbar2_readLong(MCFSIM_GPIO1_READ) >> 4)) & 0xf;
printf(" (Switch=%1X)\n", val8);
/*
* Set LED on
*/
val = mbar2_readLong(MCFSIM_GPIO1_OUT) & ~CFG_GPIO1_LED;
mbar2_writeLong(MCFSIM_GPIO1_OUT, val); /* Set LED on */
return 0;
};
phys_size_t initdram (int board_type) {
unsigned long junk = 0xa5a59696;
/*
* Note:
* RC = ([(RefreshTime/#rows) / (1/BusClk)] / 16) - 1
*/
#ifdef CFG_FAST_CLK
/*
* Busclk=70MHz, RefreshTime=64ms, #rows=4096 (4K)
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=39
*/
mbar_writeShort(MCFSIM_DCR, 0x8239);
#elif CFG_PLL_BYPASS
/*
* Busclk=5.6448MHz, RefreshTime=64ms, #rows=8192 (8K)
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=02
*/
mbar_writeShort(MCFSIM_DCR, 0x8202);
#else
/*
* Busclk=36MHz, RefreshTime=64ms, #rows=4096 (4K)
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=22 (562 bus clock cycles)
*/
mbar_writeShort(MCFSIM_DCR, 0x8222);
#endif
/*
* SDRAM starts at 0x0000_0000, CASL=10, CBM=010, PS=10 (16bit port),
* PM=1 (continuous page mode)
*/
/* RE=0 (keep auto-refresh disabled while setting up registers) */
mbar_writeLong(MCFSIM_DACR0, 0x00003324);
/* BAM=007c (bits 22,21 are bank selects; 256kB blocks) */
mbar_writeLong(MCFSIM_DMR0, 0x01fc0001);
/** Precharge sequence **/
mbar_writeLong(MCFSIM_DACR0, 0x0000332c); /* Set DACR0[IP] (bit 3) */
*((volatile unsigned long *) 0x00) = junk; /* write to a memory location to init. precharge */
udelay(0x10); /* Allow several Precharge cycles */
/** Refresh Sequence **/
mbar_writeLong(MCFSIM_DACR0, 0x0000b324); /* Enable the refresh bit, DACR0[RE] (bit 15) */
udelay(0x7d0); /* Allow gobs of refresh cycles */
/** Mode Register initialization **/
mbar_writeLong(MCFSIM_DACR0, 0x0000b364); /* Enable DACR0[IMRS] (bit 6); RE remains enabled */
*((volatile unsigned long *) 0x800) = junk; /* Access RAM to initialize the mode register */
return CFG_SDRAM_SIZE * 1024 * 1024;
};
int testdram (void) {
/* TODO: XXX XXX XXX */
printf ("DRAM test not implemented!\n");
return (0);
}