mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 00:47:26 +00:00
d98f191aff
Currently, U-Boot ignores the BBT stored in the last 4 blocks of NAND flash because the NAND_BBT_USE_FLASH flag is not set. This leads to two issues: * U-Boot silently uses a memory-only BBT which is initialized with all blocks marked as good. This means, actual bad blocks are marked good and U-Boot might try writing to or reading from them. * The BBT in flash, which will be created once Linux boots up, is not off limits for a driver ontop, like UBI. While it does not seem to consistently produce an error, sometimes UBI will fail to attach because the BBT blocks obviously don't contain valid UBI data. To fix this, this patch sets the CONFIG_SYS_NAND_USE_FLASH_BBT option, which is used in ./drivers/mtd/nand/raw/mxs_nand.c to decide whether a BBT in flash is used. Signed-off-by: Harald Seiler <hws@denx.de>
99 lines
2.6 KiB
C
99 lines
2.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) Stefano Babic <sbabic@denx.de>
|
|
*/
|
|
|
|
|
|
#ifndef __PCM058_CONFIG_H
|
|
#define __PCM058_CONFIG_H
|
|
|
|
#ifdef CONFIG_SPL
|
|
#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
|
|
#include "imx6_spl.h"
|
|
#endif
|
|
|
|
#include "mx6_common.h"
|
|
|
|
/* Thermal */
|
|
#define CONFIG_IMX_THERMAL
|
|
|
|
/* Serial */
|
|
#define CONFIG_MXC_UART
|
|
#define CONFIG_MXC_UART_BASE UART2_BASE
|
|
#define CONSOLE_DEV "ttymxc1"
|
|
|
|
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
|
|
|
|
/* Early setup */
|
|
|
|
|
|
/* Size of malloc() pool */
|
|
#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
|
|
|
|
/* Ethernet */
|
|
#define CONFIG_FEC_MXC
|
|
#define IMX_FEC_BASE ENET_BASE_ADDR
|
|
#define CONFIG_FEC_XCV_TYPE RGMII
|
|
#define CONFIG_ETHPRIME "FEC"
|
|
#define CONFIG_FEC_MXC_PHYADDR 3
|
|
|
|
/* SPI Flash */
|
|
#define CONFIG_SF_DEFAULT_BUS 0
|
|
#define CONFIG_SF_DEFAULT_CS 0
|
|
#define CONFIG_SF_DEFAULT_SPEED 20000000
|
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
/* Enable NAND support */
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x40000000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
#define CONFIG_SYS_NAND_USE_FLASH_BBT
|
|
#endif
|
|
|
|
/* DMA stuff, needed for GPMI/MXS NAND support */
|
|
|
|
/* Filesystem support */
|
|
|
|
/* Physical Memory Map */
|
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
/* MMC Configs */
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 1
|
|
|
|
/* Environment organization */
|
|
#define CONFIG_ENV_SIZE (16 * 1024)
|
|
#define CONFIG_ENV_OFFSET (1024 * SZ_1K)
|
|
#define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
|
|
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
|
|
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
|
|
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
|
|
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
|
|
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
|
|
CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_NAND
|
|
#define CONFIG_ENV_OFFSET (0x1E0000)
|
|
#define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
|
|
#endif
|
|
|
|
#endif
|