mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 13:56:30 +00:00
d4d7730853
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
183 lines
4.2 KiB
ArmAsm
183 lines
4.2 KiB
ArmAsm
#define ASSEMBLY
|
|
|
|
#include <linux/config.h>
|
|
#include <config.h>
|
|
#include <asm/blackfin.h>
|
|
#include <asm/mem_init.h>
|
|
#include <asm/mach-common/bits/bootrom.h>
|
|
#include <asm/mach-common/bits/ebiu.h>
|
|
#include <asm/mach-common/bits/pll.h>
|
|
#include <asm/mach-common/bits/uart.h>
|
|
.global init_sdram;
|
|
|
|
#if (CONFIG_CCLK_DIV == 1)
|
|
#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
|
|
#endif
|
|
#if (CONFIG_CCLK_DIV == 2)
|
|
#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
|
|
#endif
|
|
#if (CONFIG_CCLK_DIV == 4)
|
|
#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
|
|
#endif
|
|
#if (CONFIG_CCLK_DIV == 8)
|
|
#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
|
|
#endif
|
|
#ifndef CONFIG_CCLK_ACT_DIV
|
|
#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
|
|
#endif
|
|
|
|
init_sdram:
|
|
[--SP] = ASTAT;
|
|
[--SP] = RETS;
|
|
[--SP] = (R7:0);
|
|
[--SP] = (P5:0);
|
|
|
|
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
|
|
p0.h = hi(SPI_BAUD);
|
|
p0.l = lo(SPI_BAUD);
|
|
r0.l = CONFIG_SPI_BAUD_INITBLOCK;
|
|
w[p0] = r0.l;
|
|
SSYNC;
|
|
#endif
|
|
|
|
/*
|
|
* PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
|
|
*/
|
|
p0.h = hi(PLL_LOCKCNT);
|
|
p0.l = lo(PLL_LOCKCNT);
|
|
r0 = 0x300(Z);
|
|
w[p0] = r0.l;
|
|
ssync;
|
|
|
|
/*
|
|
* Put SDRAM in self-refresh, incase anything is running
|
|
*/
|
|
P2.H = hi(EBIU_SDGCTL);
|
|
P2.L = lo(EBIU_SDGCTL);
|
|
R0 = [P2];
|
|
BITSET (R0, 24);
|
|
[P2] = R0;
|
|
SSYNC;
|
|
|
|
/*
|
|
* Set PLL_CTL with the value that we calculate in R0
|
|
* - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
|
|
* - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
|
|
* - [7] = output delay (add 200ps of delay to mem signals)
|
|
* - [6] = input delay (add 200ps of input delay to mem signals)
|
|
* - [5] = PDWN : 1=All Clocks off
|
|
* - [3] = STOPCK : 1=Core Clock off
|
|
* - [1] = PLL_OFF : 1=Disable Power to PLL
|
|
* - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
|
|
* all other bits set to zero
|
|
*/
|
|
|
|
r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
|
|
r0 = r0 << 9; /* Shift it over, */
|
|
r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
|
|
r0 = r1 | r0;
|
|
r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
|
|
r1 = r1 << 8; /* Shift it over */
|
|
r0 = r1 | r0; /* add them all together */
|
|
|
|
p0.h = hi(PLL_CTL);
|
|
p0.l = lo(PLL_CTL); /* Load the address */
|
|
cli r2; /* Disable interrupts */
|
|
ssync;
|
|
w[p0] = r0.l; /* Set the value */
|
|
idle; /* Wait for the PLL to stablize */
|
|
sti r2; /* Enable interrupts */
|
|
|
|
check_again:
|
|
p0.h = hi(PLL_STAT);
|
|
p0.l = lo(PLL_STAT);
|
|
R0 = W[P0](Z);
|
|
CC = BITTST(R0,5);
|
|
if ! CC jump check_again;
|
|
|
|
/* Configure SCLK & CCLK Dividers */
|
|
r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
|
|
p0.h = hi(PLL_DIV);
|
|
p0.l = lo(PLL_DIV);
|
|
w[p0] = r0.l;
|
|
ssync;
|
|
|
|
/*
|
|
* We now are running at speed, time to set the Async mem bank wait states
|
|
* This will speed up execution, since we are normally running from FLASH.
|
|
*/
|
|
|
|
p2.h = (EBIU_AMBCTL1 >> 16);
|
|
p2.l = (EBIU_AMBCTL1 & 0xFFFF);
|
|
r0.h = (AMBCTL1VAL >> 16);
|
|
r0.l = (AMBCTL1VAL & 0xFFFF);
|
|
[p2] = r0;
|
|
ssync;
|
|
|
|
p2.h = (EBIU_AMBCTL0 >> 16);
|
|
p2.l = (EBIU_AMBCTL0 & 0xFFFF);
|
|
r0.h = (AMBCTL0VAL >> 16);
|
|
r0.l = (AMBCTL0VAL & 0xFFFF);
|
|
[p2] = r0;
|
|
ssync;
|
|
|
|
p2.h = (EBIU_AMGCTL >> 16);
|
|
p2.l = (EBIU_AMGCTL & 0xffff);
|
|
r0 = AMGCTLVAL;
|
|
w[p2] = r0;
|
|
ssync;
|
|
|
|
/*
|
|
* Now, Initialize the SDRAM,
|
|
* start with the SDRAM Refresh Rate Control Register
|
|
*/
|
|
p0.l = lo(EBIU_SDRRC);
|
|
p0.h = hi(EBIU_SDRRC);
|
|
r0 = mem_SDRRC;
|
|
w[p0] = r0.l;
|
|
ssync;
|
|
|
|
/*
|
|
* SDRAM Memory Bank Control Register - bank specific parameters
|
|
*/
|
|
p0.l = (EBIU_SDBCTL & 0xFFFF);
|
|
p0.h = (EBIU_SDBCTL >> 16);
|
|
r0 = mem_SDBCTL;
|
|
w[p0] = r0.l;
|
|
ssync;
|
|
|
|
/*
|
|
* SDRAM Global Control Register - global programmable parameters
|
|
* Disable self-refresh
|
|
*/
|
|
P2.H = hi(EBIU_SDGCTL);
|
|
P2.L = lo(EBIU_SDGCTL);
|
|
R0 = [P2];
|
|
BITCLR (R0, 24);
|
|
|
|
/*
|
|
* Check if SDRAM is already powered up, if it is, enable self-refresh
|
|
*/
|
|
p0.h = hi(EBIU_SDSTAT);
|
|
p0.l = lo(EBIU_SDSTAT);
|
|
r2.l = w[p0];
|
|
cc = bittst(r2,3);
|
|
if !cc jump skip;
|
|
NOP;
|
|
BITSET (R0, 23);
|
|
skip:
|
|
[P2] = R0;
|
|
SSYNC;
|
|
|
|
/* Write in the new value in the register */
|
|
R0.L = lo(mem_SDGCTL);
|
|
R0.H = hi(mem_SDGCTL);
|
|
[P2] = R0;
|
|
SSYNC;
|
|
nop;
|
|
|
|
(P5:0) = [SP++];
|
|
(R7:0) = [SP++];
|
|
RETS = [SP++];
|
|
ASTAT = [SP++];
|
|
RTS;
|