u-boot/doc/device-tree-bindings/video/exynos_mipi_dsi.txt
Piotr Wilczek de461c526e video:mipidsim:fdt: Add DT support for mipi dsim driver
This patch enables parsing mipi data from device tree.
Non device tree case is still supported.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:54:59 +09:00

82 lines
3.3 KiB
Text

Exynos MIPI-DSIM Controller
=========================
Required properties:
SOC specific:
compatible: should be "samsung,exynos-mipi-dsi"
reg: Base address of MIPI-DSIM IP.
Board specific:
samsung,dsim-config-e-interface: interface to be used (RGB interface
for main display or CPU interface for main or sub display).
samsung,dsim-config-e-virtual-ch: virtual channel number that main
or sub display uses.
samsung,dsim-config-e-pixel-format: pixel stream format for main
or sub display.
samsung,dsim-config-e-burst-mode: selects Burst mode in Video mode.
in Non-burst mode, RGB data area is filled with RGB data and
NULL packets, according to input bandwidth of RGB interface.
samsung,dsim-config-e-no-data-lane: data lane count used by Master.
samsung,dsim-config-e-byte-clk: select byte clock source.
It must be DSIM_PLL_OUT_DIV8.
DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported.
samsung,dsim-config-hfp: HFP disable mode.
If set, DSI master ignores HFP area in VIDEO mode.
In command mode, this variable is ignored.
samsung,dsim-config-p: P value for PMS setting.
samsung,dsim-config-m: M value for PMS setting.
samsung,dsim-config-s: S value for PMS setting.
samsung,dsim-config-pll-stable-time: the PLL Timer for stability
of the ganerated clock.
samsung,dsim-config-esc-clk: escape clock frequency for getting
the escape clock prescaler value.
samsung,dsim-config-stop-holding-cnt: the interval value between
transmitting read packet (or write "set_tear_on" command)
and BTA request. After transmitting read packet or write
"set_tear_on" command, BTA requests to D-PHY automatically.
This counter value specifies the interval between them.
samsung,dsim-config-bta-timeout: the timer for BTA. This register
specifies time out from BTA request to change the direction
with respect to Tx escape clock.
samsung,dsim-config-rx-timeout: the timer for LP Rx mode timeout.
this register specifies time out on how long RxValid deasserts,
after RxLpdt asserts with respect to Tx escape clock.
- RxValid specifies Rx data valid indicator.
- RxLpdt specifies an indicator that D-PHY is under RxLpdt mode
- RxValid and RxLpdt specifies signal from D-PHY.
samsung,dsim-device-name: name of the device.
samsung,dsim-device-id: unique device id.
samsung,dsim-device-bus_id: bus id for identifing connected bus
and this bus id should be same as id of mipi_dsim_device.
Optional properties:
samsung,dsim-device-reverse-panel: reverse panel.
Example:
mipidsi@11c80000 {
compatible = "samsung,exynos-mipi-dsi";
reg = <0x11c80000 0x5c>;
samsung,dsim-config-e-interface = <1>;
samsung,dsim-config-e-virtual-ch = <0>;
samsung,dsim-config-e-pixel-format = <7>;
samsung,dsim-config-e-burst-mode = <1>;
samsung,dsim-config-e-no-data-lane = <3>;
samsung,dsim-config-e-byte-clk = <0>;
samsung,dsim-config-hfp = <1>;
samsung,dsim-config-p = <3>;
samsung,dsim-config-m = <120>;
samsung,dsim-config-s = <1>;
samsung,dsim-config-pll-stable-time = <500>;
samsung,dsim-config-esc-clk = <20000000>;
samsung,dsim-config-stop-holding-cnt = <0x7ff>;
samsung,dsim-config-bta-timeout = <0xff>;
samsung,dsim-config-rx-timeout = <0xffff>;
samsung,dsim-device-id = <0xffffffff>;
samsung,dsim-device-bus-id = <0>;
samsung,dsim-device-reverse-panel = <1>;
};