u-boot/board/freescale/imx8mn_evk/spl.c
Ye Li 98bcdf1635 imx8mn: Add low drive mode support for DDR4/LPDDR4 EVK
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00

167 lines
3.5 KiB
C

/*
* Copyright 2018-2019 NXP
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <hang.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mn_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/arch/ddr.h>
#include <dm/uclass.h>
#include <dm/device.h>
#include <dm/uclass-internal.h>
#include <dm/device-internal.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <fsl_esdhc_imx.h>
#include <mmc.h>
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
return BOOT_DEVICE_BOOTROM;
}
void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
void spl_board_init(void)
{
struct udevice *dev;
int ret;
puts("Normal Boot\n");
ret = uclass_get_device_by_name(UCLASS_CLK,
"clock-controller@30380000",
&dev);
if (ret < 0)
printf("Failed to find clock node. Check device tree\n");
}
#if CONFIG_IS_ENABLED(DM_PMIC_PCA9450)
int power_init_board(void)
{
struct udevice *dev;
int ret;
ret = pmic_get("pca9450@25", &dev);
if (ret == -ENODEV) {
puts("No pca9450@25\n");
return 0;
}
if (ret != 0)
return ret;
/* BUCKxOUT_DVS0/1 control BUCK123 output */
pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29);
#ifdef CONFIG_IMX8MN_LOW_DRIVE_MODE
/* Set VDD_SOC/VDD_DRAM to 0.8v for low drive mode */
pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x10);
#else
/* increase VDD_SOC/VDD_DRAM to typical value 0.95V before first DRAM access */
pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1C);
#endif
/* Set DVS1 to 0.85v for suspend */
/* Enable DVS control through PMIC_STBY_REQ and set B1_ENMODE=1 (ON by PMIC_ON_REQ=H) */
pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14);
pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59);
/* set VDD_SNVS_0V8 from default 0.85V */
pmic_reg_write(dev, PCA9450_LDO2CTRL, 0xC0);
/* enable LDO4 to 1.2v */
pmic_reg_write(dev, PCA9450_LDO4CTRL, 0x44);
/* set WDOG_B_CFG to cold reset */
pmic_reg_write(dev, PCA9450_RESET_CTRL, 0xA1);
return 0;
}
#endif
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
static iomux_v3_cfg_t const uart_pads[] = {
IMX8MN_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
IMX8MN_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MN_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
int board_early_init_f(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
return 0;
}
void board_init_f(ulong dummy)
{
int ret;
arch_cpu_init();
init_uart_clk(1);
board_early_init_f();
timer_init();
preloader_console_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
ret = spl_init();
if (ret) {
debug("spl_init() failed: %d\n", ret);
hang();
}
enable_tzc380();
/* DDR initialization */
spl_dram_init();
board_init_r(NULL, 0);
}