Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-14 17:07:38 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/include/configs/MPC8610HPCD.h
Jon Loeliger 1a247ba7fa Merge commit 'wd/master'
2008-06-06 10:48:31 -05:00

684 lines
21 KiB
C
Raw Blame History

/*
* Copyright 2007 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
/*
* MPC8610HPCD board configuration file
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_MPC86xx 1 /* MPC86xx */
#define CONFIG_MPC8610 1 /* MPC8610 specific */
#define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */
#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */
/* video */
#undef CONFIG_VIDEO
#if defined(CONFIG_VIDEO)
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#endif
#ifdef RUN_DIAG
#define CFG_DIAG_ADDR 0xff800000
#endif
#define CFG_RESET_ADDRESS 0xfff00100
#define CONFIG_PCI 1 /* Enable PCI/PCIE*/
#define CONFIG_PCI1 1 /* PCI controler 1 */
#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
#undef CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
#define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */
#define CONFIG_ALTIVEC 1
/*
* L2CR setup -- make sure this is right for your board!
*/
#define CFG_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E |0x00100000 )
#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
#define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000)
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
#if defined(CONFIG_SPD_EEPROM)
/*
* Determine DDR configuration from I2C interface.
*/
#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
#else
/*
* Manually set up DDR1 parameters
*/
#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
#if 0 /* TODO */
#define CFG_DDR_CS0_BNDS 0x0000000F
#define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
#define CFG_DDR_TIMING_3 0x00000000
#define CFG_DDR_TIMING_0 0x00260802
#define CFG_DDR_TIMING_1 0x3935d322
#define CFG_DDR_TIMING_2 0x14904cc8
#define CFG_DDR_MODE_1 0x00480432
#define CFG_DDR_MODE_2 0x00000000
#define CFG_DDR_INTERVAL 0x06180100
#define CFG_DDR_DATA_INIT 0xdeadbeef
#define CFG_DDR_CLK_CTRL 0x03800000
#define CFG_DDR_OCD_CTRL 0x00000000
#define CFG_DDR_OCD_STATUS 0x00000000
#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
#define CFG_DDR_CONTROL2 0x04400010
#define CFG_DDR_ERR_INT_EN 0x00000000
#define CFG_DDR_ERR_DIS 0x00000000
#define CFG_DDR_SBE 0x000f0000
/* Not used in fixed_sdram function */
#define CFG_DDR_MODE 0x00000022
#define CFG_DDR_CS1_BNDS 0x00000000
#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
#endif
#endif
#define CFG_ID_EEPROM
#ifdef CFG_ID_EEPROM
#define CONFIG_ID_EEPROM
#endif
#define ID_EEPROM_ADDR 0x57
#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
#define CFG_FLASH_BASE2 0xf8000000
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
#define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */
#define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
#define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */
#define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
#if 0 /* TODO */
#define CFG_BR2_PRELIM 0xf0000000
#define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
#endif
#define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */
#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xe8000000 /* PIXIS registers */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */
#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/
#define PIXIS_VCTL 0x10 /* VELA Control Register */
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
#define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef CFG_RAMBOOT
#endif
#if defined(CFG_RAMBOOT)
#undef CONFIG_SPD_EEPROM
#define CFG_SDRAM_SIZE 256
#endif
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#ifndef CFG_INIT_RAM_LOCK
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#else
#define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
#endif
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
#define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/*
* Pass open firmware flat tree to kernel
*/
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
#define CFG_64BIT_VSPRINTF 1
#define CFG_64BIT_STRTOUL 1
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe1000000
#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
/* PCI view of System Memory */
#define CFG_PCI_MEMORY_BUS 0x00000000
#define CFG_PCI_MEMORY_PHYS 0x00000000
#define CFG_PCI_MEMORY_SIZE 0x80000000
/* For RTL8139 */
#define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
#define _IO_BASE 0x00000000
/* controller 1, Base address 0xa000 */
#define CFG_PCIE1_MEM_BASE 0xa0000000
#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCIE1_IO_BASE 0x00000000
#define CFG_PCIE1_IO_PHYS 0xe3000000
#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
/* controller 2, Base Address 0x9000 */
#define CFG_PCIE2_MEM_BASE 0x90000000
#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */
#define CFG_PCIE2_IO_PHYS 0xe2000000
#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_NET_MULTI
#define CONFIG_CMD_NET
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_CMD_REGINFO
#define CONFIG_ULI526X
#ifdef CONFIG_ULI526X
#define CONFIG_ETHADDR 00:E0:0C:00:00:01
#endif
/************************************************************
* USB support
************************************************************/
#define CONFIG_PCI_OHCI 1
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_KEYBOARD 1
#define CFG_DEVICE_DEREGISTER
#define CFG_USB_EVENT_POLL 1
#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#define CFG_OHCI_SWAP_REG_ACCESS 1
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
#define CFG_SCSI_MAX_SCSI_ID 4
#define CFG_SCSI_MAX_LUN 1
#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
#endif
#endif /* CONFIG_PCI */
/*
* BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
*/
#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
#define CFG_IBAT0U CFG_DBAT0U
/*
* BAT1 1G Cache-inhibited, guarded
* 0x8000_0000 256M PCI-1 Memory
* 0xa000_0000 256M PCI-Express 1 Memory
* 0x9000_0000 256M PCI-Express 2 Memory
*/
#define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT1U CFG_DBAT1U
/*
* BAT2 16M Cache-inhibited, guarded
* 0xe100_0000 1M PCI-1 I/O
*/
#define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
#define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT2U CFG_DBAT2U
/*
* BAT3 32M Cache-inhibited, guarded
* 0xe200_0000 1M PCI-Express 2 I/O
* 0xe300_0000 1M PCI-Express 1 I/O
*/
#define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT3U CFG_DBAT3U
/*
* BAT4 4M Cache-inhibited, guarded
* 0xe000_0000 4M CCSR
*/
#define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
#define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT4U CFG_DBAT4U
/*
* BAT5 128K Cacheable, non-guarded
* 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CFG_IBAT5L CFG_DBAT5L
#define CFG_IBAT5U CFG_DBAT5U
/*
* BAT6 256M Cache-inhibited, guarded
* 0xf000_0000 256M FLASH
*/
#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_IBAT6U CFG_DBAT6U
/*
* BAT7 4M Cache-inhibited, guarded
* 0xe800_0000 4M PIXIS
*/
#define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
#define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT7U CFG_DBAT7U
/*
* Environment
*/
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
#define CFG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
#endif
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_USB
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*DIU Configuration*/
#define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#define CONFIG_IPADDR 192.168.1.100
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#if defined(CONFIG_PCI1)
#define PCI_ENV \
"pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
"echo e;md ${a}e00 9\0" \
"pci1regs=setenv a e0008; run pcireg\0" \
"pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
"pci d.w $b.0 56 1\0" \
"pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
"pci w.w $b.0 56 ffff\0" \
"pci1err=setenv a e0008; run pcierr\0" \
"pci1errc=setenv a e0008; run pcierrc\0"
#else
#define PCI_ENV ""
#endif
#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
#define PCIE_ENV \
"pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
"pcie1regs=setenv a e000a; run pciereg\0" \
"pcie2regs=setenv a e0009; run pciereg\0" \
"pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
"pci d $b.0 130 1\0" \
"pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
"pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
"pcie1err=setenv a e000a; run pcieerr\0" \
"pcie2err=setenv a e0009; run pcieerr\0" \
"pcie1errc=setenv a e000a; run pcieerrc\0" \
"pcie2errc=setenv a e0009; run pcieerrc\0"
#else
#define PCIE_ENV ""
#endif
#define DMA_ENV \
"dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
"dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
"dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
"dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
#ifdef ENV_DEBUG
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " MK_STR(TEXT_BASE) " +$filesize; " \
"erase " MK_STR(TEXT_BASE) " +$filesize; " \
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
"bdev=sda3\0" \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
"maxcpus=1" \
"eoi=mw e00400b0 0\0" \
"iack=md e00400a0 1\0" \
"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
"md ${a}f00 5\0" \
"ddr1regs=setenv a e0002; run ddrreg\0" \
"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
"md ${a}e60 1; md ${a}ef0 1d\0" \
"guregs=setenv a e00e0; run gureg\0" \
"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
"mcmregs=setenv a e0001; run mcmreg\0" \
"diuregs=md e002c000 1d\0" \
"dium=mw e002c01c\0" \
"diuerr=md e002c014 1\0" \
"othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \
"monitor=0-DVI\0" \
"pmregs=md e00e1000 2b\0" \
"lawregs=md e0000c08 4b\0" \
"lbcregs=md e0005000 36\0" \
"dma0regs=md e0021100 12\0" \
"dma1regs=md e0021180 12\0" \
"dma2regs=md e0021200 12\0" \
"dma3regs=md e0021280 12\0" \
PCI_ENV \
PCIE_ENV \
DMA_ENV
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
"bdev=sda3\0" \
"othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\
"monitor=0-DVI\0"
#endif
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#endif /* __CONFIG_H */
Reference in a new issue View git blame Copy permalink