mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 13:44:29 +00:00
a0dbc1314c
Tegra186 build are currently dealt with in very special ways, which is because Tegra186 is fundamentally different in many respects. It is no longer necessary to do many of the low-level programming because early boot firmware will already have taken care of it. Unfortunately, separating Tegra186 builds from the rest in this way makes it difficult to share code with prior generations of Tegra. With all of the low-level programming code behind Kconfig guards, the build for Tegra186 can again be unified. As a side-effect, and partial reason for this change, other Tegra SoC generations can now make use of the code that deals with taking over a boot from earlier bootloaders. This used to be nvtboot, but has been replaced by cboot nowadays. Rename the files and functions related to this to avoid confusion. The implemented protocols are unchanged. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
54 lines
1.3 KiB
C
54 lines
1.3 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (c) 2016, NVIDIA CORPORATION
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include "../p2571/max77620_init.h"
|
|
|
|
void pin_mux_mmc(void)
|
|
{
|
|
struct udevice *dev;
|
|
uchar val;
|
|
int ret;
|
|
|
|
/* Turn on MAX77620 LDO3 to 3.3V for SD card power */
|
|
debug("%s: Set LDO3 for VDDIO_SDMMC_AP power to 3.3V\n", __func__);
|
|
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
|
return;
|
|
}
|
|
/* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
|
val = 0xF2;
|
|
ret = dm_i2c_write(dev, MAX77620_CNFG1_L3_REG, &val, 1);
|
|
if (ret) {
|
|
printf("i2c_write 0 0x3c 0x27 failed: %d\n", ret);
|
|
return;
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_PCI_TEGRA
|
|
int tegra_pcie_board_init(void)
|
|
{
|
|
struct udevice *dev;
|
|
uchar val;
|
|
int ret;
|
|
|
|
/* Turn on MAX77620 LDO7 to 1.05V for PEX power */
|
|
debug("%s: Set LDO7 for PEX power to 1.05V\n", __func__);
|
|
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
|
return -1;
|
|
}
|
|
/* 0xC5 for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
|
val = 0xC5;
|
|
ret = dm_i2c_write(dev, MAX77620_CNFG1_L7_REG, &val, 1);
|
|
if (ret)
|
|
printf("i2c_write 0 0x3c 0x31 failed: %d\n", ret);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|