mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 05:42:58 +00:00
d92cb66236
A number of platforms are still defining CONFIG_SYS_BAUDRATE_TABLE to the fallback default of "{ 9600, 19200, 38400, 57600, 115200 }", but with varying whitespace, or were introduced after the default fallback was added. Use the default table here. Signed-off-by: Tom Rini <trini@konsulko.com>
208 lines
6.2 KiB
C
208 lines
6.2 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2017 NXP
|
|
* Copyright (C) 2014 Freescale Semiconductor
|
|
*/
|
|
|
|
#ifndef __LS2_COMMON_H
|
|
#define __LS2_COMMON_H
|
|
|
|
#define CONFIG_REMAKE_ELF
|
|
|
|
#include <asm/arch/stream_id_lsch3.h>
|
|
#include <asm/arch/config.h>
|
|
|
|
/* Link Definitions */
|
|
#ifdef CONFIG_TFABOOT
|
|
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
|
|
#else
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
|
|
#endif
|
|
|
|
/* We need architecture specific misc initializations */
|
|
|
|
/* Link Definitions */
|
|
|
|
#ifndef CONFIG_SYS_FSL_DDR4
|
|
#define CONFIG_SYS_DDR_RAW_TIMING
|
|
#endif
|
|
|
|
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
|
|
|
|
#define CONFIG_VERY_BIG_RAM
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
|
|
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
|
|
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
|
|
|
|
/*
|
|
* SMP Definitinos
|
|
*/
|
|
#define CPU_RELEASE_ADDR secondary_boot_addr
|
|
|
|
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
|
|
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
|
|
#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
|
|
/*
|
|
* DDR controller use 0 as the base address for binding.
|
|
* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
|
|
*/
|
|
#define CONFIG_SYS_DP_DDR_BASE_PHY 0
|
|
#define CONFIG_DP_DDR_CTRL 2
|
|
#define CONFIG_DP_DDR_NUM_CTRLS 1
|
|
#endif
|
|
|
|
/* Generic Timer Definitions */
|
|
/*
|
|
* This is not an accurate number. It is used in start.S. The frequency
|
|
* will be udpated later when get_bus_freq(0) is available.
|
|
*/
|
|
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
|
|
|
|
/* GPIO */
|
|
#ifdef CONFIG_DM_GPIO
|
|
#ifndef CONFIG_MPC8XXX_GPIO
|
|
#define CONFIG_MPC8XXX_GPIO
|
|
#endif
|
|
#endif
|
|
|
|
/* I2C */
|
|
|
|
/* Serial Port */
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
|
|
|
|
/* IFC */
|
|
#define CONFIG_FSL_IFC
|
|
|
|
/*
|
|
* During booting, IFC is mapped at the region of 0x30000000.
|
|
* But this region is limited to 256MB. To accommodate NOR, promjet
|
|
* and FPGA. This region is divided as below:
|
|
* 0x30000000 - 0x37ffffff : 128MB : NOR flash
|
|
* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
|
|
* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
|
|
*
|
|
* To accommodate bigger NOR flash and other devices, we will map IFC
|
|
* chip selects to as below:
|
|
* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
|
|
* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
|
|
* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
|
|
* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
|
|
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
|
|
*
|
|
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
|
|
* CONFIG_SYS_FLASH_BASE has the final address (core view)
|
|
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
|
|
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
|
|
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
|
|
*/
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
|
|
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
|
|
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
|
|
|
|
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
|
|
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
|
|
|
|
#ifndef __ASSEMBLY__
|
|
unsigned long long get_qixis_addr(void);
|
|
#endif
|
|
#define QIXIS_BASE get_qixis_addr()
|
|
#define QIXIS_BASE_PHYS 0x20000000
|
|
#define QIXIS_BASE_PHYS_EARLY 0xC000000
|
|
#define QIXIS_STAT_PRES1 0xb
|
|
#define QIXIS_SDID_MASK 0x07
|
|
#define QIXIS_ESDHC_NO_ADAPTER 0x7
|
|
|
|
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
|
|
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
|
|
|
|
/* MC firmware */
|
|
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
|
|
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
|
|
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
|
|
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
|
|
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
|
|
/* For LS2085A */
|
|
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
|
|
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
|
|
|
|
/* Define phy_reset function to boot the MC based on mcinitcmd.
|
|
* This happens late enough to properly fixup u-boot env MAC addresses.
|
|
*/
|
|
#define CONFIG_RESET_PHY_R
|
|
|
|
/*
|
|
* Carve out a DDR region which will not be used by u-boot/Linux
|
|
*
|
|
* It will be used by MC and Debug Server. The MC region must be
|
|
* 512MB aligned, so the min size to hide is 512MB.
|
|
*/
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
|
|
#endif
|
|
|
|
/* Miscellaneous configurable options */
|
|
|
|
/* Physical Memory Map */
|
|
/* fixme: these need to be checked against the board */
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
|
|
|
#define CONFIG_HWCONFIG
|
|
#define HWCONFIG_BUFFER_SIZE 128
|
|
|
|
/* Initial environment variables */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x80100000\0" \
|
|
"kernel_addr=0x100000\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x581000000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"console=ttyAMA0,38400n8\0" \
|
|
"mcinitcmd=fsl_mc start mc 0x580a00000" \
|
|
" 0x580e00000 \0"
|
|
|
|
#ifndef CONFIG_TFABOOT
|
|
#ifdef CONFIG_SD_BOOT
|
|
#define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\
|
|
" fsl_mc apply dpl 0x80200000 &&" \
|
|
" mmc read $kernel_load $kernel_start" \
|
|
" $kernel_size && bootm $kernel_load"
|
|
#else
|
|
#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
|
|
" cp.b $kernel_start $kernel_load" \
|
|
" $kernel_size && bootm $kernel_load"
|
|
#endif
|
|
#endif
|
|
|
|
/* Monitor Command Prompt */
|
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 64 /* max command args */
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
|
|
#define CONFIG_SPL_MAX_SIZE 0x16000
|
|
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
|
|
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
|
|
#endif
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
|
|
#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
|
|
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
#include <asm/arch/soc.h>
|
|
|
|
#endif /* __LS2_COMMON_H */
|