u-boot/board/samsung/trats2/trats2.c
Simon Glass 7f1961018c dm: exynos: Make sure that GPIOs are requested
With driver model GPIOs must be requested before use. Make sure this is
done correctly.

(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:33 -06:00

433 lines
11 KiB
C

/*
* Copyright (c) 2013 Samsung Electronics Co., Ltd. All rights reserved.
* Sanghee Kim <sh0130.kim@samsung.com>
* Piotr Wilczek <p.wilczek@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <lcd.h>
#include <asm/gpio.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
#include <asm/arch/mipi_dsim.h>
#include <power/pmic.h>
#include <power/max77686_pmic.h>
#include <power/battery.h>
#include <power/max77693_pmic.h>
#include <power/max77693_muic.h>
#include <power/max77693_fg.h>
#include <libtizen.h>
#include <errno.h>
#include <usb.h>
#include <usb/s3c_udc.h>
#include <usb_mass_storage.h>
DECLARE_GLOBAL_DATA_PTR;
static unsigned int board_rev = -1;
static inline u32 get_model_rev(void);
static void check_hw_revision(void)
{
int modelrev = 0;
char str[12];
int i;
/*
* GPM1[1:0]: MODEL_REV[1:0]
* Don't set as pull-none for these N/C pin.
* TRM say that it may cause unexcepted state and leakage current.
* and pull-none is only for output function.
*/
for (i = 0; i < 2; i++) {
int pin = i + EXYNOS4X12_GPIO_M10;
sprintf(str, "model_rev%d", i);
gpio_request(pin, str);
gpio_cfg_pin(pin, S5P_GPIO_INPUT);
}
/* GPM1[5:2]: HW_REV[3:0] */
for (i = 0; i < 4; i++) {
int pin = i + EXYNOS4X12_GPIO_M12;
sprintf(str, "hw_rev%d", i);
gpio_request(pin, str);
gpio_cfg_pin(pin, S5P_GPIO_INPUT);
gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
}
/* GPM1[1:0]: MODEL_REV[1:0] */
for (i = 0; i < 2; i++)
modelrev |= (gpio_get_value(EXYNOS4X12_GPIO_M10 + i) << i);
/* board_rev[15:8] = model */
board_rev = modelrev << 8;
}
u32 get_board_rev(void)
{
return board_rev;
}
static inline u32 get_model_rev(void)
{
return (board_rev >> 8) & 0xff;
}
static void board_external_gpio_init(void)
{
/*
* some pins which in alive block are connected with external pull-up
* but it's default setting is pull-down.
* if that pin set as input then that floated
*/
gpio_set_pull(EXYNOS4X12_GPIO_X02, S5P_GPIO_PULL_NONE); /* PS_ALS_INT */
gpio_set_pull(EXYNOS4X12_GPIO_X04, S5P_GPIO_PULL_NONE); /* TSP_nINT */
gpio_set_pull(EXYNOS4X12_GPIO_X07, S5P_GPIO_PULL_NONE); /* AP_PMIC_IRQ*/
gpio_set_pull(EXYNOS4X12_GPIO_X15, S5P_GPIO_PULL_NONE); /* IF_PMIC_IRQ*/
gpio_set_pull(EXYNOS4X12_GPIO_X20, S5P_GPIO_PULL_NONE); /* VOL_UP */
gpio_set_pull(EXYNOS4X12_GPIO_X21, S5P_GPIO_PULL_NONE); /* VOL_DOWN */
gpio_set_pull(EXYNOS4X12_GPIO_X23, S5P_GPIO_PULL_NONE); /* FUEL_ALERT */
gpio_set_pull(EXYNOS4X12_GPIO_X24, S5P_GPIO_PULL_NONE); /* ADC_INT */
gpio_set_pull(EXYNOS4X12_GPIO_X27, S5P_GPIO_PULL_NONE); /* nPOWER */
gpio_set_pull(EXYNOS4X12_GPIO_X30, S5P_GPIO_PULL_NONE); /* WPC_INT */
gpio_set_pull(EXYNOS4X12_GPIO_X35, S5P_GPIO_PULL_NONE); /* OK_KEY */
gpio_set_pull(EXYNOS4X12_GPIO_X37, S5P_GPIO_PULL_NONE); /* HDMI_HPD */
}
#ifdef CONFIG_SYS_I2C_INIT_BOARD
static void board_init_i2c(void)
{
int err;
/* I2C_7 */
err = exynos_pinmux_config(PERIPH_ID_I2C7, PINMUX_FLAG_NONE);
if (err) {
debug("I2C%d not configured\n", (I2C_7));
return;
}
/* I2C_8 */
gpio_request(EXYNOS4X12_GPIO_F14, "i2c8_clk");
gpio_request(EXYNOS4X12_GPIO_F15, "i2c8_data");
gpio_direction_output(EXYNOS4X12_GPIO_F14, 1);
gpio_direction_output(EXYNOS4X12_GPIO_F15, 1);
/* I2C_9 */
gpio_request(EXYNOS4X12_GPIO_M21, "i2c9_clk");
gpio_request(EXYNOS4X12_GPIO_M20, "i2c9_data");
gpio_direction_output(EXYNOS4X12_GPIO_M21, 1);
gpio_direction_output(EXYNOS4X12_GPIO_M20, 1);
}
#endif
#ifdef CONFIG_SYS_I2C_SOFT
int get_soft_i2c_scl_pin(void)
{
if (I2C_ADAP_HWNR)
return EXYNOS4X12_GPIO_M21; /* I2C9 */
else
return EXYNOS4X12_GPIO_F14; /* I2C8 */
}
int get_soft_i2c_sda_pin(void)
{
if (I2C_ADAP_HWNR)
return EXYNOS4X12_GPIO_M20; /* I2C9 */
else
return EXYNOS4X12_GPIO_F15; /* I2C8 */
}
#endif
int exynos_early_init_f(void)
{
board_external_gpio_init();
return 0;
}
static int pmic_init_max77686(void);
int exynos_init(void)
{
struct exynos4_power *pwr =
(struct exynos4_power *)samsung_get_base_power();
check_hw_revision();
printf("HW Revision:\t0x%04x\n", board_rev);
/*
* First bootloader on the TRATS2 platform uses
* INFORM4 and INFORM5 registers for recovery
*
* To indicate correct boot chain - those two
* registers must be cleared out
*/
writel(0, &pwr->inform4);
writel(0, &pwr->inform5);
return 0;
}
int exynos_power_init(void)
{
int chrg;
struct power_battery *pb;
struct pmic *p_chrg, *p_muic, *p_fg, *p_bat;
#ifdef CONFIG_SYS_I2C_INIT_BOARD
board_init_i2c();
#endif
pmic_init(I2C_7); /* I2C adapter 7 - bus name s3c24x0_7 */
pmic_init_max77686();
pmic_init_max77693(I2C_10); /* I2C adapter 10 - bus name soft1 */
power_muic_init(I2C_10); /* I2C adapter 10 - bus name soft1 */
power_fg_init(I2C_9); /* I2C adapter 9 - bus name soft0 */
power_bat_init(0);
p_chrg = pmic_get("MAX77693_PMIC");
if (!p_chrg) {
puts("MAX77693_PMIC: Not found\n");
return -ENODEV;
}
p_muic = pmic_get("MAX77693_MUIC");
if (!p_muic) {
puts("MAX77693_MUIC: Not found\n");
return -ENODEV;
}
p_fg = pmic_get("MAX77693_FG");
if (!p_fg) {
puts("MAX17042_FG: Not found\n");
return -ENODEV;
}
if (p_chrg->chrg->chrg_bat_present(p_chrg) == 0)
puts("No battery detected\n");
p_bat = pmic_get("BAT_TRATS2");
if (!p_bat) {
puts("BAT_TRATS2: Not found\n");
return -ENODEV;
}
p_fg->parent = p_bat;
p_chrg->parent = p_bat;
p_muic->parent = p_bat;
p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic);
pb = p_bat->pbat;
chrg = p_muic->chrg->chrg_type(p_muic);
debug("CHARGER TYPE: %d\n", chrg);
if (!p_chrg->chrg->chrg_bat_present(p_chrg)) {
puts("No battery detected\n");
return 0;
}
p_fg->fg->fg_battery_check(p_fg, p_bat);
if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
puts("CHARGE Battery !\n");
return 0;
}
#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
int ret = 0;
unsigned int val;
struct pmic *p, *p_pmic, *p_muic;
p_pmic = pmic_get("MAX77686_PMIC");
if (!p_pmic)
return -ENODEV;
if (pmic_probe(p_pmic))
return -1;
p_muic = pmic_get("MAX77693_MUIC");
if (!p_muic)
return -ENODEV;
if (pmic_probe(p_muic))
return -1;
if (on) {
ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON);
if (ret)
return -1;
p = pmic_get("MAX77693_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return -1;
/* SAFEOUT */
ret = pmic_reg_read(p, MAX77693_SAFEOUT, &val);
if (ret)
return -1;
val |= MAX77693_ENSAFEOUT1;
ret = pmic_reg_write(p, MAX77693_SAFEOUT, val);
if (ret)
return -1;
/* PATH: USB */
ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
MAX77693_MUIC_CTRL1_DN1DP2);
} else {
ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM);
if (ret)
return -1;
/* PATH: UART */
ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
MAX77693_MUIC_CTRL1_UT1UR2);
}
if (ret)
return -1;
return 0;
}
struct s3c_plat_otg_data s5pc210_otg_data = {
.phy_control = s5pc210_phy_control,
.regs_phy = EXYNOS4X12_USBPHY_BASE,
.regs_otg = EXYNOS4X12_USBOTG_BASE,
.usb_phy_ctrl = EXYNOS4X12_USBPHY_CONTROL,
.usb_flags = PHY0_SLEEP,
};
int board_usb_init(int index, enum usb_init_type init)
{
debug("USB_udc_probe\n");
return s3c_udc_probe(&s5pc210_otg_data);
}
int g_dnl_board_usb_cable_connected(void)
{
struct pmic *muic = pmic_get("MAX77693_MUIC");
if (!muic)
return 0;
return !!muic->chrg->chrg_type(muic);
}
#endif
static int pmic_init_max77686(void)
{
struct pmic *p = pmic_get("MAX77686_PMIC");
if (pmic_probe(p))
return -1;
/* BUCK/LDO Output Voltage */
max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 VTF_2.8V */
max77686_set_ldo_voltage(p, 23, 3300000); /* LDO23 TSP_AVDD_3.3V*/
max77686_set_ldo_voltage(p, 24, 1800000); /* LDO24 TSP_VDD_1.8V */
/* BUCK/LDO Output Mode */
max77686_set_buck_mode(p, 1, OPMODE_STANDBY); /* BUCK1 VMIF_1.1V_AP */
max77686_set_buck_mode(p, 2, OPMODE_ON); /* BUCK2 VARM_1.0V_AP */
max77686_set_buck_mode(p, 3, OPMODE_ON); /* BUCK3 VINT_1.0V_AP */
max77686_set_buck_mode(p, 4, OPMODE_ON); /* BUCK4 VG3D_1.0V_AP */
max77686_set_buck_mode(p, 5, OPMODE_ON); /* BUCK5 VMEM_1.2V_AP */
max77686_set_buck_mode(p, 6, OPMODE_ON); /* BUCK6 VCC_SUB_1.35V*/
max77686_set_buck_mode(p, 7, OPMODE_ON); /* BUCK7 VCC_SUB_2.0V */
max77686_set_buck_mode(p, 8, OPMODE_OFF); /* VMEM_VDDF_2.85V */
max77686_set_buck_mode(p, 9, OPMODE_OFF); /* CAM_ISP_CORE_1.2V*/
max77686_set_ldo_mode(p, 1, OPMODE_LPM); /* LDO1 VALIVE_1.0V_AP*/
max77686_set_ldo_mode(p, 2, OPMODE_STANDBY); /* LDO2 VM1M2_1.2V_AP */
max77686_set_ldo_mode(p, 3, OPMODE_LPM); /* LDO3 VCC_1.8V_AP */
max77686_set_ldo_mode(p, 4, OPMODE_LPM); /* LDO4 VCC_2.8V_AP */
max77686_set_ldo_mode(p, 5, OPMODE_OFF); /* LDO5_VCC_1.8V_IO */
max77686_set_ldo_mode(p, 6, OPMODE_STANDBY); /* LDO6 VMPLL_1.0V_AP */
max77686_set_ldo_mode(p, 7, OPMODE_STANDBY); /* LDO7 VPLL_1.0V_AP */
max77686_set_ldo_mode(p, 8, OPMODE_LPM); /* LDO8 VMIPI_1.0V_AP */
max77686_set_ldo_mode(p, 9, OPMODE_OFF); /* CAM_ISP_MIPI_1.2*/
max77686_set_ldo_mode(p, 10, OPMODE_LPM); /* LDO10 VMIPI_1.8V_AP*/
max77686_set_ldo_mode(p, 11, OPMODE_STANDBY); /* LDO11 VABB1_1.8V_AP*/
max77686_set_ldo_mode(p, 12, OPMODE_LPM); /* LDO12 VUOTG_3.0V_AP*/
max77686_set_ldo_mode(p, 13, OPMODE_OFF); /* LDO13 VC2C_1.8V_AP */
max77686_set_ldo_mode(p, 14, OPMODE_STANDBY); /* VABB02_1.8V_AP */
max77686_set_ldo_mode(p, 15, OPMODE_STANDBY); /* LDO15 VHSIC_1.0V_AP*/
max77686_set_ldo_mode(p, 16, OPMODE_STANDBY); /* LDO16 VHSIC_1.8V_AP*/
max77686_set_ldo_mode(p, 17, OPMODE_OFF); /* CAM_SENSOR_CORE_1.2*/
max77686_set_ldo_mode(p, 18, OPMODE_OFF); /* CAM_ISP_SEN_IO_1.8V*/
max77686_set_ldo_mode(p, 19, OPMODE_OFF); /* LDO19 VT_CAM_1.8V */
max77686_set_ldo_mode(p, 20, OPMODE_ON); /* LDO20 VDDQ_PRE_1.8V*/
max77686_set_ldo_mode(p, 21, OPMODE_OFF); /* LDO21 VTF_2.8V */
max77686_set_ldo_mode(p, 22, OPMODE_OFF); /* LDO22 VMEM_VDD_2.8V*/
max77686_set_ldo_mode(p, 23, OPMODE_OFF); /* LDO23 TSP_AVDD_3.3V*/
max77686_set_ldo_mode(p, 24, OPMODE_OFF); /* LDO24 TSP_VDD_1.8V */
max77686_set_ldo_mode(p, 25, OPMODE_OFF); /* LDO25 VCC_3.3V_LCD */
max77686_set_ldo_mode(p, 26, OPMODE_OFF); /*LDO26 VCC_3.0V_MOTOR*/
return 0;
}
/*
* LCD
*/
#ifdef CONFIG_LCD
int mipi_power(void)
{
struct pmic *p = pmic_get("MAX77686_PMIC");
/* LDO8 VMIPI_1.0V_AP */
max77686_set_ldo_mode(p, 8, OPMODE_ON);
/* LDO10 VMIPI_1.8V_AP */
max77686_set_ldo_mode(p, 10, OPMODE_ON);
return 0;
}
void exynos_lcd_power_on(void)
{
struct pmic *p = pmic_get("MAX77686_PMIC");
/* LCD_2.2V_EN: GPC0[1] */
gpio_request(EXYNOS4X12_GPIO_C01, "lcd_2v2_en");
gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4X12_GPIO_C01, 1);
/* LDO25 VCC_3.1V_LCD */
pmic_probe(p);
max77686_set_ldo_voltage(p, 25, 3100000);
max77686_set_ldo_mode(p, 25, OPMODE_LPM);
}
void exynos_reset_lcd(void)
{
/* reset lcd */
gpio_request(EXYNOS4X12_GPIO_F21, "lcd_reset");
gpio_direction_output(EXYNOS4X12_GPIO_F21, 0);
udelay(10);
gpio_set_value(EXYNOS4X12_GPIO_F21, 1);
}
void exynos_lcd_misc_init(vidinfo_t *vid)
{
#ifdef CONFIG_TIZEN
get_tizen_logo_info(vid);
#endif
#ifdef CONFIG_S6E8AX0
s6e8ax0_init();
#endif
}
#endif /* LCD */