mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-29 14:33:08 +00:00
42c9a494f1
Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value
of either 0x00040000 or 0x00000000.
CONFIG_SYS_LBC_MRTPR always has the value 0x20000000.
CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board.
CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000).
To simplify the configuration files, hardcode the setting of these
values for mpc83xx.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
390 lines
11 KiB
C
390 lines
11 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2007 Freescale Semiconductor, Inc.
|
|
* Dave Liu <daveliu@freescale.com>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1 /* E300 family */
|
|
|
|
/*
|
|
* IP blocks clock configuration
|
|
*/
|
|
#define CONFIG_SYS_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */
|
|
#define CONFIG_SYS_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */
|
|
#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */
|
|
|
|
/*
|
|
* System IO Config
|
|
*/
|
|
#define CONFIG_SYS_SICRH 0x00000000
|
|
#define CONFIG_SYS_SICRL 0x00000000
|
|
|
|
/*
|
|
* Output Buffer Impedance
|
|
*/
|
|
#define CONFIG_SYS_OBIR 0x31100000
|
|
|
|
#define CONFIG_HWCONFIG
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
|
|
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
|
#define CONFIG_SYS_83XX_DDR_USES_CS0
|
|
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
|
|
| DDRCDR_ODT \
|
|
| DDRCDR_Q_DRN)
|
|
/* 0x80080001 */ /* ODT 150ohm on SoC */
|
|
|
|
#undef CONFIG_DDR_ECC /* support DDR ECC function */
|
|
#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
|
|
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
|
|
#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
|
|
|
|
#if defined(CONFIG_SPD_EEPROM)
|
|
#define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */
|
|
#else
|
|
/*
|
|
* Manually set up DDR parameters
|
|
* WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
|
|
* consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
|
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 512 /* MB */
|
|
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
|
|
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
|
| CSCONFIG_ODT_RD_NEVER /* ODT_RD to none */ \
|
|
| CSCONFIG_ODT_WR_ONLY_CURRENT /* ODT_WR to CSn */ \
|
|
| CSCONFIG_ROW_BIT_14 \
|
|
| CSCONFIG_COL_BIT_10)
|
|
/* 0x80010202 */
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
|
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
|
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
|
| (0 << TIMING_CFG0_RRT_SHIFT) \
|
|
| (0 << TIMING_CFG0_WWT_SHIFT) \
|
|
| (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
|
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
|
/* 0x00620802 */
|
|
#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
|
|
| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
|
| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
|
|
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
|
|
| (13 << TIMING_CFG1_REFREC_SHIFT) \
|
|
| (3 << TIMING_CFG1_WRREC_SHIFT) \
|
|
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
|
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
|
/* 0x3935d322 */
|
|
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
|
| (6 << TIMING_CFG2_CPO_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
|
| (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
|
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
|
| (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
|
/* 0x131088c8 */
|
|
#define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
|
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
|
/* 0x03E00100 */
|
|
#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
|
|
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
|
|
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
|
|
| (0x1432 << SDRAM_MODE_SD_SHIFT))
|
|
/* ODT 150ohm CL=3, AL=1 on SDRAM */
|
|
#define CONFIG_SYS_DDR_MODE2 0x00000000
|
|
#endif
|
|
|
|
/*
|
|
* Memory test
|
|
*/
|
|
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
|
|
#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00140000
|
|
|
|
/*
|
|
* The reserved memory
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#else
|
|
#undef CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Initial RAM Base Address Setup
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
#define CONFIG_FSL_ELBC 1
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
|
|
#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */
|
|
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
|
|
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
/*
|
|
* BCSR on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_BCSR 0xF8000000
|
|
/* Access window base at BCSR base */
|
|
|
|
/*
|
|
* NAND Flash on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_NAND_FSL_ELBC 1
|
|
|
|
#define CONFIG_SYS_NAND_BASE 0xE0600000
|
|
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
|
|
|
|
/*
|
|
* Config on-board RTC
|
|
*/
|
|
#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
|
|
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
|
|
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
|
|
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
|
|
#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
|
|
#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
|
|
|
|
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
|
|
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
|
|
|
|
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
|
|
#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
|
|
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000
|
|
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
|
|
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
|
|
|
|
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
|
|
#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
|
|
#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000
|
|
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
|
|
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
#ifndef __ASSEMBLY__
|
|
extern int board_pci_host_broken(void);
|
|
#endif
|
|
#define CONFIG_PCIE
|
|
#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */
|
|
|
|
#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */
|
|
#define CONFIG_USB_EHCI_FSL
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
#undef CONFIG_EEPRO100
|
|
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
|
#endif /* CONFIG_PCI */
|
|
|
|
/*
|
|
* TSEC
|
|
*/
|
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
|
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
|
|
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
|
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
|
|
|
|
/*
|
|
* TSEC ethernet configuration
|
|
*/
|
|
#define CONFIG_TSEC1 1
|
|
#define CONFIG_TSEC1_NAME "eTSEC0"
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "eTSEC1"
|
|
#define TSEC1_PHY_ADDR 2
|
|
#define TSEC2_PHY_ADDR 3
|
|
#define TSEC1_PHY_ADDR_SGMII 8
|
|
#define TSEC2_PHY_ADDR_SGMII 4
|
|
#define TSEC1_PHYIDX 0
|
|
#define TSEC2_PHYIDX 0
|
|
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
|
|
/* Options are: TSEC[0-1] */
|
|
#define CONFIG_ETHPRIME "eTSEC1"
|
|
|
|
/* SERDES */
|
|
#define CONFIG_FSL_SERDES
|
|
#define CONFIG_FSL_SERDES1 0xe3000
|
|
#define CONFIG_FSL_SERDES2 0xe3100
|
|
|
|
/*
|
|
* SATA
|
|
*/
|
|
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
|
#define CONFIG_SATA1
|
|
#define CONFIG_SYS_SATA1_OFFSET 0x18000
|
|
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
|
|
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
|
#define CONFIG_SATA2
|
|
#define CONFIG_SYS_SATA2_OFFSET 0x19000
|
|
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
|
|
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
|
|
|
#ifdef CONFIG_FSL_SATA
|
|
#define CONFIG_LBA48
|
|
#endif
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#ifndef CONFIG_SYS_RAMBOOT
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#else
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#ifdef CONFIG_MMC
|
|
#define CONFIG_FSL_ESDHC_PIN_MUX
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
|
|
#endif
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 256 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#if defined(CONFIG_TSEC_ENET)
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_HAS_ETH1
|
|
#endif
|
|
|
|
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=1000000\0" \
|
|
"ramdiskfile=ramfs.83xx\0" \
|
|
"fdtaddr=780000\0" \
|
|
"fdtfile=mpc8379_mds.dtb\0" \
|
|
""
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
|
|
"$netdev:off " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
|
|
|
|
#endif /* __CONFIG_H */
|