u-boot/include/configs/mx6sabre_common.h
Ye.Li 6c920ee910 mx6: mx6sabre common: Enable i.MX thermal DM driver
Enable i.MX thermal DM driver to mx6sabre_common.h file. Since the
thermal is used in init_sequence_f, so define the CONFIG_SYS_MALLOC_F_LEN
to support DM driver using in pre relocation phase.

Additional, thermal driver depends on ocotp, make sure to enable
CONFIG_MXC_OCOTP when CONFIG_IMX6_THERMAL is selected.

Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
2014-11-21 15:30:12 +01:00

285 lines
7.4 KiB
C

/*
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale i.MX6Q SabreSD board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __MX6QSABRE_COMMON_CONFIG_H
#define __MX6QSABRE_COMMON_CONFIG_H
#define CONFIG_MX6
#include "mx6_common.h"
#include <linux/sizes.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#include <asm/arch/imx-regs.h>
#include <asm/imx-common/gpio.h>
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_DM
#define CONFIG_DM_THERMAL
#define CONFIG_SYS_MALLOC_F_LEN (1 << 10)
#define CONFIG_IMX6_THERMAL
#define CONFIG_SYS_GENERIC_BOARD
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART
#define CONFIG_CMD_FUSE
#if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX6_THERMAL)
#define CONFIG_MXC_OCOTP
#endif
/* MMC Configs */
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 1
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_CMD_SF
#ifdef CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/* Command definition */
#include <config_cmd_default.h>
#define CONFIG_CMD_BMODE
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_SETEXPR
#undef CONFIG_CMD_IMLS
#define CONFIG_BOOTDELAY 1
#define CONFIG_LOADADDR 0x12000000
#define CONFIG_SYS_TEXT_BASE 0x17800000
#ifdef CONFIG_SUPPORT_EMMC_BOOT
#define EMMC_ENV \
"emmcdev=2\0" \
"update_emmc_firmware=" \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
"if mmc dev ${emmcdev} && " \
"mmc open ${emmcdev} 1; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"mmc close ${emmcdev} 1; " \
"fi; " \
"fi\0"
#else
#define EMMC_ENV ""
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr=0x18000000\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
"console=" CONFIG_CONSOLE_DEV "\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=1\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"update_sd_firmware=" \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if mmc dev ${mmcdev}; then " \
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
EMMC_ENV \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
"if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"fi; " \
"else run netboot; fi"
#define CONFIG_ARP_TIMEOUT 200UL
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
#define CONFIG_STACKSIZE (128 * 1024)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_IS_IN_MMC
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_ENV_OFFSET (8 * 64 * 1024)
#endif
#define CONFIG_OF_LIBFDT
#ifndef CONFIG_SYS_DCACHE_OFF
#define CONFIG_CMD_CACHE
#endif
/* Framebuffer */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
#endif /* __MX6QSABRE_COMMON_CONFIG_H */