mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-26 22:52:18 +00:00
4d66668300
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework. PBL initializes the internal CPC-SRAM and copy SPL(160K) to it, SPL further initializes DDR using SPD and environment and copy u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
114 lines
3 KiB
C
114 lines
3 KiB
C
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 or later as published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <hwconfig.h>
|
|
#include <asm/mmu.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
#include <asm/fsl_law.h>
|
|
#include "ddr.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
ulong ddr_freq;
|
|
|
|
if (ctrl_num > 1) {
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
|
return;
|
|
}
|
|
if (!pdimm->n_ranks)
|
|
return;
|
|
|
|
pbsp = udimms[0];
|
|
|
|
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
while (pbsp->datarate_mhz_high) {
|
|
if (pbsp->n_ranks == pdimm->n_ranks &&
|
|
(pdimm->rank_density >> 30) >= pbsp->rank_gb) {
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
goto found;
|
|
}
|
|
pbsp_highest = pbsp;
|
|
}
|
|
pbsp++;
|
|
}
|
|
|
|
if (pbsp_highest) {
|
|
printf("Error: board specific timing not found");
|
|
printf("for data rate %lu MT/s\n", ddr_freq);
|
|
printf("Trying to use the highest speed (%u) parameters\n",
|
|
pbsp_highest->datarate_mhz_high);
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
} else {
|
|
panic("DIMM is not supported by this board");
|
|
}
|
|
found:
|
|
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
|
|
"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
|
|
"wrlvl_ctrl_3 0x%x\n",
|
|
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
|
|
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
|
|
pbsp->wrlvl_ctl_3);
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 0;
|
|
/*
|
|
* Write leveling override
|
|
*/
|
|
popts->wrlvl_override = 1;
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
/*
|
|
* Rtt and Rtt_WR override
|
|
*/
|
|
popts->rtt_override = 0;
|
|
|
|
/* Enable ZQ calibration */
|
|
popts->zq_en = 1;
|
|
|
|
/* DHC_EN =1, ODT = 75 Ohm */
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
|
}
|
|
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
phys_size_t dram_size;
|
|
|
|
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
|
|
puts("Initializing....using SPD\n");
|
|
dram_size = fsl_ddr_sdram();
|
|
|
|
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
|
|
dram_size *= 0x100000;
|
|
#else
|
|
/* DDR has been initialised by first stage boot loader */
|
|
dram_size = fsl_ddr_sdram_size();
|
|
#endif
|
|
return dram_size;
|
|
}
|