mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 09:30:10 +00:00
bc2d40ca10
In the earlier patches, the SPL/TPL fraamework was introduced. For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The SPL was loaded by the code from the internal on-chip ROM. The SPL initializes the DDR according to the SPD and loads the final uboot image into DDR, then jump to the DDR to begin execution. For NAND booting way, the nand SPL has size limitation on some board(e.g. P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD and loads the final uboot image into DDR,then jump to the DDR to begin execution. This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL. Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to execute, so the section .resetvec is no longer needed. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
141 lines
3.3 KiB
C
141 lines
3.3 KiB
C
/*
|
|
* Copyright 2013 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <ns16550.h>
|
|
#include <malloc.h>
|
|
#include <mmc.h>
|
|
#include <nand.h>
|
|
#include <i2c.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <spi_flash.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define SYSCLK_MASK 0x00200000
|
|
#define BOARDREV_MASK 0x10100000
|
|
|
|
#define SYSCLK_66 66666666
|
|
#define SYSCLK_100 100000000
|
|
|
|
unsigned long get_board_sys_clk(ulong dummy)
|
|
{
|
|
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
|
|
u32 val_gpdat, sysclk_gpio;
|
|
|
|
val_gpdat = in_be32(&pgpio->gpdat);
|
|
sysclk_gpio = val_gpdat & SYSCLK_MASK;
|
|
|
|
if (sysclk_gpio == 0)
|
|
return SYSCLK_66;
|
|
else
|
|
return SYSCLK_100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
phys_size_t get_effective_memsize(void)
|
|
{
|
|
return CONFIG_SYS_L2_SIZE;
|
|
}
|
|
|
|
void board_init_f(ulong bootflag)
|
|
{
|
|
u32 plat_ratio, bus_clk;
|
|
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
|
|
|
|
console_init_f();
|
|
|
|
/* Set pmuxcr to allow both i2c1 and i2c2 */
|
|
setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
|
|
setbits_be32(&gur->pmuxcr,
|
|
in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
|
|
|
|
/* Read back the register to synchronize the write. */
|
|
in_be32(&gur->pmuxcr);
|
|
|
|
#ifdef CONFIG_SPL_SPI_BOOT
|
|
clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
|
|
#endif
|
|
|
|
/* initialize selected port with appropriate baud rate */
|
|
plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
|
|
plat_ratio >>= 1;
|
|
bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
|
|
gd->bus_clk = bus_clk;
|
|
|
|
NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
|
|
bus_clk / 16 / CONFIG_BAUDRATE);
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
puts("\nSD boot...\n");
|
|
#elif defined(CONFIG_SPL_SPI_BOOT)
|
|
puts("\nSPI Flash boot...\n");
|
|
#endif
|
|
|
|
/* copy code to RAM and jump to it - this should not return */
|
|
/* NOTE - code has to be copied out of NAND buffer before
|
|
* other blocks can be read.
|
|
*/
|
|
relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
|
|
}
|
|
|
|
void board_init_r(gd_t *gd, ulong dest_addr)
|
|
{
|
|
/* Pointer is writable since we allocated a register for it */
|
|
gd = (gd_t *)CONFIG_SPL_GD_ADDR;
|
|
bd_t *bd;
|
|
|
|
memset(gd, 0, sizeof(gd_t));
|
|
bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
|
|
memset(bd, 0, sizeof(bd_t));
|
|
gd->bd = bd;
|
|
bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
|
|
bd->bi_memsize = CONFIG_SYS_L2_SIZE;
|
|
|
|
probecpu();
|
|
get_clocks();
|
|
mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
|
|
CONFIG_SPL_RELOC_MALLOC_SIZE);
|
|
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
mmc_initialize(bd);
|
|
#endif
|
|
/* relocate environment function pointers etc. */
|
|
#ifdef CONFIG_SPL_NAND_BOOT
|
|
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
#ifdef CONFIG_SPL_NAND_BOOT
|
|
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
#ifdef CONFIG_SPL_SPI_BOOT
|
|
spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
|
|
gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
|
|
gd->env_valid = 1;
|
|
|
|
gd->ram_size = initdram(0);
|
|
#ifdef CONFIG_SPL_NAND_BOOT
|
|
puts("Tertiary program loader running in sram...");
|
|
#else
|
|
puts("Second program loader running in sram...\n");
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
mmc_boot();
|
|
#elif defined(CONFIG_SPL_SPI_BOOT)
|
|
spi_boot();
|
|
#elif defined(CONFIG_SPL_NAND_BOOT)
|
|
nand_boot();
|
|
#endif
|
|
}
|