u-boot/board/freescale/p2020ds/ddr.c
York Sun 8d9207c792 Fix parameters to support RDIMM for P2020DS
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-31 11:23:04 -05:00

128 lines
3.6 KiB
C

/*
* Copyright 2008-2009 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
static void get_spd(generic_spd_eeprom_t *spd, unsigned char i2c_address)
{
i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
}
unsigned int fsl_ddr_get_mem_data_rate(void)
{
return get_ddr_freq(0);
}
void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
unsigned int ctrl_num)
{
unsigned int i;
unsigned int i2c_address = 0;
for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
if (ctrl_num == 0 && i == 0)
i2c_address = SPD_EEPROM_ADDRESS1;
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
typedef struct {
u32 datarate_mhz_low;
u32 datarate_mhz_high;
u32 n_ranks;
u32 clk_adjust;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
} board_specific_parameters_t;
/* ranges for parameters:
* wr_data_delay = 0-6
* clk adjust = 0-8
* cpo 2-0x1E (30)
*/
const board_specific_parameters_t board_specific_parameters[][20] = {
{
/* memory controller 0 */
/* lo| hi| num| clk| cpo|wrdata|2T */
/* mhz| mhz|ranks|adjst| | delay| */
#ifdef CONFIG_FSL_DDR2
{ 0, 333, 2, 4, 0x1f, 2, 0},
{334, 400, 2, 4, 0x1f, 2, 0},
{401, 549, 2, 4, 0x1f, 2, 0},
{550, 680, 2, 4, 0x1f, 3, 0},
{681, 850, 2, 4, 0x1f, 4, 0},
{ 0, 333, 1, 4, 0x1f, 2, 0},
{334, 400, 1, 4, 0x1f, 2, 0},
{401, 549, 1, 4, 0x1f, 2, 0},
{550, 680, 1, 4, 0x1f, 3, 0},
{681, 850, 1, 4, 0x1f, 4, 0}
#else
{ 0, 850, 2, 6, 0x1f, 4, 0},
{ 0, 850, 1, 4, 0x1f, 4, 0}
#endif
},
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const board_specific_parameters_t *pbsp =
&(board_specific_parameters[ctrl_num][0]);
u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
sizeof(board_specific_parameters[0][0]);
u32 i;
ulong ddr_freq;
/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
* that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
* there are two dimms in the controller, set odt_rd_cfg to 3 and
* odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 1;
}
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
for (i = 0; i < num_params; i++) {
if (ddr_freq >= pbsp->datarate_mhz_low &&
ddr_freq <= pbsp->datarate_mhz_high &&
pdimm->n_ranks == pbsp->n_ranks) {
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay = pbsp->write_data_delay;
popts->twoT_en = pbsp->force_2T;
}
pbsp++;
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
popts->wrlvl_en = 1;
/* Write leveling override */
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xa;
popts->wrlvl_start = 0x8;
/* Rtt and Rtt_WR override */
popts->rtt_override = 1;
popts->rtt_override_value = DDR3_RTT_120_OHM;
popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
}