u-boot/include/configs/PATI.h
Simon Glass a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00

250 lines
8.8 KiB
C

/*
* (C) Copyright 2003
* Denis Peter d.peter@mpl.ch
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* File: PATI.h
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_MPC555 1 /* This is an MPC555 CPU */
#define CONFIG_PATI 1 /* ...On a PATI board */
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
/* Serial Console Configuration */
#define CONFIG_5xx_CONS_SCI1
#undef CONFIG_5xx_CONS_SCI2
#define CONFIG_BAUDRATE 9600
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IRQ
#define CONFIG_BOOTCOMMAND "" /* autoboot command */
#define CONFIG_BOOTARGS "" /* */
#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */
/*
* Miscellaneous configurable options
*/
#define CONFIG_PREBOOT
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00010000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00A00000 /* 10 MB in SRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 }
/***********************************************************************
* Last Stage Init
***********************************************************************/
#define CONFIG_LAST_STAGE_INIT
/*
* Low Level Configuration Settings
*/
/*
* Internal Memory Mapped (This is not the IMMR content)
*/
#define CONFIG_SYS_IMMR 0x01C00000 /* Physical start adress of internal memory map */
/*
* Definitions for initial stack pointer and data area
*/
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_IMMR + 0x03fa000) /* Physical start adress of inital stack */
/*
* Start addresses for the final memory configuration
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
#define CONFIG_SYS_FLASH_BASE 0xffC00000 /* External flash */
#define PCI_BASE 0x03000000 /* PCI Base (CS2) */
#define PCI_CONFIG_BASE 0x04000000 /* PCI & PLD (CS3) */
#define PLD_CONFIG_BASE 0x04001000 /* PLD (CS3) */
#define CONFIG_SYS_MONITOR_BASE 0xFFF00000
/* CONFIG_SYS_FLASH_BASE */ /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */
/* This adress is given to the linker with -Ttext to */
/* locate the text section at this adress. */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 192 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_RESET_ADDRESS (PLD_CONFIG_BASE + 0x10) /* Adress which causes reset */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_FLASH_SHOW_PROGRESS 45
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 128
#define CONFIG_ENV_IS_IN_EEPROM
#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_OFFSET 0
#define CONFIG_ENV_SIZE 2048
#endif
#undef CONFIG_ENV_IS_IN_FLASH
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 0x00002000 /* Set whole sector as env */
#define CONFIG_ENV_OFFSET ((0 - CONFIG_SYS_FLASH_BASE) - CONFIG_ENV_SIZE) /* Environment starts at this adress */
#endif
#define CONFIG_SPI 1
#define CONFIG_SYS_SPI_CS_USED 0x09 /* CS0 and CS3 are used */
#define CONFIG_SYS_SPI_CS_BASE 0x08 /* CS3 is active low */
#define CONFIG_SYS_SPI_CS_ACT 0x00 /* CS3 is active low */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* SW Watchdog freeze
*/
#undef CONFIG_WATCHDOG
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF00
#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \
SCCR_COM01 | SCCR_DFNL000 | SCCR_DFNH000)
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration
*-----------------------------------------------------------------------
* Data show cycle
*/
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register
*-----------------------------------------------------------------------
* Set all bits to 40 Mhz
*
*/
#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0)
/*-----------------------------------------------------------------------
* UMCR - UIMB Module Configuration Register
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
/*-----------------------------------------------------------------------
* ICTRL - I-Bus Support Control Register
*/
#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
/*-----------------------------------------------------------------------
* USIU - Memory Controller Register
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16 | BR_SETA)
#define CONFIG_SYS_OR0_PRELIM (0xffc00000) /* SCY is not used if external TA is set */
/* SDRAM */
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA)
#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FF) /* SCY is not used if external TA is set */
/* PCI */
#define CONFIG_SYS_BR2_PRELIM (PCI_BASE | BR_V | BR_PS_32 | BR_SETA)
#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF)
/* config registers: */
#define CONFIG_SYS_BR3_PRELIM (PCI_CONFIG_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA)
#define CONFIG_SYS_OR3_PRELIM (0xffff0000)
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */
/*-----------------------------------------------------------------------
* DER - Timer Decrementer
*-----------------------------------------------------------------------
* Initialise to zero
*/
#define CONFIG_SYS_DER 0x00000000
#endif /* __CONFIG_H */