u-boot/include/configs/usb_a9263.h
Nikita Kiryanov 181bd9dc61 kconfig: add config option for shell prompt
Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
  entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
  CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
  right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
  CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
  files. This results in a streamlined default value across platforms, and
  includes the following files: spear-common, sunxi-common, mv-common,
  ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
  not updated in their respective defconfig files under the assumption that
  since they did not explicitly define a value, they're fine with whatever
  the default is.
- On the other hand, boards that relied on a value defined in some
  <boards>_common.h file such as woodburn_common, rpi-common,
  bur_am335x_common, ls2085a_common, siemens_am33x_common, and
  omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
  assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-13 07:19:33 -04:00

157 lines
4.1 KiB
C

/*
* (C) Copyright 2007-2013
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
* Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com>
* Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
*
* Settings for Calao USB-A9263 board
*
* U-Boot image has to be less than 200704 bytes, otherwise at91bootstrap
* installed on board will not be able to load it properly.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/hardware.h>
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_MACH_TYPE MACH_TYPE_USB_A9263
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_OF_LIBFDT
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_SYS_TEXT_BASE 0x23f00000
/*
* Hardware drivers
*/
#define CONFIG_AT91_GPIO
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NAND
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE 0x04000000
#define CONFIG_SYS_INIT_SP_ADDR \
(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
#define CONFIG_HAS_DATAFLASH
#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000
#define AT91_SPI_CLK 8000000
#define DATAFLASH_TCSS (0x1a << 16)
#define DATAFLASH_TCHS (0x1 << 24)
/* no NOR flash */
#define CONFIG_SYS_NO_FLASH
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22)
#endif
#define MTDPARTS_DEFAULT \
"mtdparts=atmel_nand:16m(kernel)ro,120m(root1),-(root2)"
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
/* bootstrap + u-boot + env in dataflash on CS0 */
#define CONFIG_ENV_IS_IN_DATAFLASH
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x4000)
#define CONFIG_ENV_OFFSET 0x2000
#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_BOOTCOMMAND "nboot 21000000 0"
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"root=/dev/mtdblock1 " \
"mtdparts=" MTDPARTS_DEFAULT " " \
"rw rootfstype=jffs2"
#define CONFIG_EXTRA_ENV_SETTINGS \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
#endif