mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-15 15:53:02 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
144 lines
3.3 KiB
C
144 lines
3.3 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright 2011 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <hwconfig.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/mmu.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
#include <asm/fsl_law.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
struct board_specific_parameters {
|
|
u32 n_ranks;
|
|
u32 datarate_mhz_high;
|
|
u32 clk_adjust;
|
|
u32 wrlvl_start;
|
|
u32 cpo;
|
|
u32 write_data_delay;
|
|
u32 force_2t;
|
|
};
|
|
|
|
/*
|
|
* This table contains all valid speeds we want to override with board
|
|
* specific parameters. datarate_mhz_high values need to be in ascending order
|
|
* for each n_ranks group.
|
|
*
|
|
* ranges for parameters:
|
|
* wr_data_delay = 0-6
|
|
* clk adjust = 0-8
|
|
* cpo 2-0x1E (30)
|
|
*/
|
|
static const struct board_specific_parameters dimm0[] = {
|
|
/*
|
|
* memory controller 0
|
|
* num| hi| clk| wrlvl | cpo |wrdata|2T
|
|
* ranks| mhz|adjst| start | delay|
|
|
*/
|
|
{2, 750, 3, 5, 0xff, 2, 0},
|
|
{2, 1250, 4, 6, 0xff, 2, 0},
|
|
{2, 1350, 5, 7, 0xff, 2, 0},
|
|
{2, 1666, 5, 8, 0xff, 2, 0},
|
|
{}
|
|
};
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
ulong ddr_freq;
|
|
|
|
if (ctrl_num) {
|
|
printf("Wrong parameter for controller number %d", ctrl_num);
|
|
return;
|
|
}
|
|
if (!pdimm->n_ranks)
|
|
return;
|
|
|
|
pbsp = dimm0;
|
|
|
|
/*
|
|
* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
while (pbsp->datarate_mhz_high) {
|
|
if (pbsp->n_ranks == pdimm->n_ranks) {
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
popts->cpo_override = pbsp->cpo;
|
|
popts->write_data_delay =
|
|
pbsp->write_data_delay;
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
popts->twot_en = pbsp->force_2t;
|
|
goto found;
|
|
}
|
|
pbsp_highest = pbsp;
|
|
}
|
|
pbsp++;
|
|
}
|
|
|
|
if (pbsp_highest) {
|
|
printf("Error: board specific timing not found "
|
|
"for data rate %lu MT/s!\n"
|
|
"Trying to use the highest speed (%u) parameters\n",
|
|
ddr_freq, pbsp_highest->datarate_mhz_high);
|
|
popts->cpo_override = pbsp_highest->cpo;
|
|
popts->write_data_delay = pbsp_highest->write_data_delay;
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
popts->twot_en = pbsp_highest->force_2t;
|
|
} else {
|
|
panic("DIMM is not supported by this board");
|
|
}
|
|
|
|
found:
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 0;
|
|
/* Write leveling override */
|
|
popts->wrlvl_override = 1;
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
/* Rtt and Rtt_WR override */
|
|
popts->rtt_override = 0;
|
|
|
|
/* Enable ZQ calibration */
|
|
popts->zq_en = 1;
|
|
|
|
/* DHC_EN =1, ODT = 60 Ohm */
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
phys_size_t dram_size = 0;
|
|
|
|
puts("Initializing....");
|
|
|
|
if (fsl_use_spd()) {
|
|
puts("using SPD\n");
|
|
dram_size = fsl_ddr_sdram();
|
|
} else {
|
|
puts("no SPD and fixed parameters\n");
|
|
return -ENXIO;
|
|
}
|
|
|
|
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
|
|
dram_size *= 0x100000;
|
|
|
|
debug(" DDR: ");
|
|
gd->ram_size = dram_size;
|
|
|
|
return 0;
|
|
}
|