u-boot/board/solidrun/clearfog/clearfog.c
Marek Behún 90bcc3d38d driver/ddr: Add support for setting timing in hws_topology_map
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.

This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
  HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
                    from the number of CSs
  HWS_TIM_1T      - enforce 1t
  HWS_TIM_2T      - enforce 2t

This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-07-12 06:56:48 +02:00

161 lines
4.4 KiB
C

/*
* Copyright (C) 2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
#include <../serdes/a38x/high_speed_env_spec.h>
DECLARE_GLOBAL_DATA_PTR;
#define ETH_PHY_CTRL_REG 0
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
/*
* Those values and defines are taken from the Marvell U-Boot version
* "u-boot-2013.01-15t1-clearfog"
*/
#define BOARD_GPP_OUT_ENA_LOW 0xffffffff
#define BOARD_GPP_OUT_ENA_MID 0xffffffff
#define BOARD_GPP_OUT_VAL_LOW 0x0
#define BOARD_GPP_OUT_VAL_MID 0x0
#define BOARD_GPP_POL_LOW 0x0
#define BOARD_GPP_POL_MID 0x0
/* IO expander on Marvell GP board includes e.g. fan enabling */
struct marvell_io_exp {
u8 chip;
u8 addr;
u8 val;
};
static struct marvell_io_exp io_exp[] = {
{ 0x20, 2, 0x40 }, /* Deassert both mini pcie reset signals */
{ 0x20, 6, 0xf9 },
{ 0x20, 2, 0x46 }, /* rst signals and ena USB3 current limiter */
{ 0x20, 6, 0xb9 },
{ 0x20, 3, 0x00 }, /* Set SFP_TX_DIS to zero */
{ 0x20, 7, 0xbf }, /* Drive SFP_TX_DIS to zero */
};
static struct serdes_map board_serdes_map[] = {
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
};
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
{
*serdes_map_array = board_serdes_map;
*count = ARRAY_SIZE(board_serdes_map);
return 0;
}
/*
* Define the DDR layout / topology here in the board file. This will
* be used by the DDR3 init code in the SPL U-Boot version to configure
* the DDR3 controller.
*/
static struct hws_topology_map board_topology_map = {
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
{ { { {0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0} },
SPEED_BIN_DDR_1600K, /* speed_bin */
BUS_WIDTH_16, /* memory_width */
MEM_4G, /* mem_size */
DDR_FREQ_800, /* frequency */
0, 0, /* cas_l cas_wl */
HWS_TEMP_LOW, /* temperature */
HWS_TIM_DEFAULT} }, /* timing */
5, /* Num Of Bus Per Interface*/
BUS_MASK_32BIT /* Busses mask */
};
struct hws_topology_map *ddr3_get_topology_map(void)
{
/* Return the board topology as defined in the board code */
return &board_topology_map;
}
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
writel(0x10400011, MVEBU_MPP_BASE + 0x08);
writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
writel(0x44400002, MVEBU_MPP_BASE + 0x10);
writel(0x41144004, MVEBU_MPP_BASE + 0x14);
writel(0x40333333, MVEBU_MPP_BASE + 0x18);
writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
/* Set GPP Out value */
writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
/* Set GPP Polarity */
writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
/* Set GPP Out Enable */
writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
return 0;
}
int board_init(void)
{
int i;
/* Address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
/* Toggle GPIO41 to reset onboard switch and phy */
clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9));
/* GPIO 19 on ClearFog rev 2.1 controls the uSOM onboard phy reset */
clrbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
clrbits_le32(MVEBU_GPIO0_BASE + 0x4, BIT(19));
mdelay(1);
setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
mdelay(10);
/* Init I2C IO expanders */
for (i = 0; i < ARRAY_SIZE(io_exp); i++)
i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
return 0;
}
int checkboard(void)
{
puts("Board: SolidRun ClearFog\n");
return 0;
}
int board_eth_init(bd_t *bis)
{
cpu_eth_init(bis); /* Built in controller(s) come first */
return pci_eth_init(bis);
}