Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-10 23:24:38 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/wandboard
History
Igor Opaniuk 2147a16983 dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO 
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.

CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.

All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
     's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +

Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-21 06:08:00 +01:00
..
Kconfig mx6: remove SYS_SOC from board Kconfig 2015-09-13 10:37:29 +02:00
MAINTAINERS imx6: wandboard: add device tree 2019-04-13 20:30:09 +02:00
Makefile wandboard: Rework Makefile to prevent spl.o from being built 2019-06-11 10:42:48 +02:00
README arm: wandboard: move CONFIG_MXC_UART to defconfig 2020-06-22 17:43:31 +02:00
spl.c treewide: convert bd_t to struct bd_info by coccinelle 2020-07-17 09:30:13 -04:00
wandboard.c dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO 2021-02-21 06:08:00 +01:00

README 

U-Boot for Wandboard
--------------------

This file contains information for the port of U-Boot to the Wandboard.

Wandboard is a development board that has three variants based on the following
SoCs: mx6 quad, mx6 quad plus, mx6 dual lite and mx6 solo.

For more details about Wandboard, please refer to:
http://www.wandboard.org/

Building U-Boot for Wandboard
-----------------------------

To build U-Boot for the Wandboard:

$ make wandboard_config
$ make

Flashing U-Boot into the SD card
--------------------------------

- After the 'make' command completes, the generated 'SPL' binary must be
flashed into the SD card;

$ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync

(Note - the SD card node may vary, so adjust this as needed).

- Flash the u-boot.img image into the SD card:

sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync

- Insert the SD card into the slot located in the bottom of the board (same side
as the mx6 processor)

- Connect the serial cable to the host PC

- Power up the board and U-Boot messages will appear in the serial console.

Debug UART
----------

The following settings provide a debug UART for the Wandboard:

CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_MXC=y
CONFIG_DEBUG_UART_BASE=0x02020000
CONFIG_DEBUG_UART_CLOCK=80000000