mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 01:38:22 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
284 lines
7.2 KiB
C
284 lines
7.2 KiB
C
/*
|
|
* (C) Copyright 2003
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* (C) Copyright 2004
|
|
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* cpci5200.c - main board support/init for the esd cpci5200.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <mpc5xxx.h>
|
|
#include <pci.h>
|
|
#include <command.h>
|
|
#include <netdev.h>
|
|
|
|
#include "mt46v16m16-75.h"
|
|
|
|
void init_ata_reset(void);
|
|
|
|
static void sdram_start(int hi_addr)
|
|
{
|
|
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
|
|
|
|
/* unlock mode register */
|
|
*(vu_long *) MPC5XXX_SDRAM_CTRL =
|
|
SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* precharge all banks */
|
|
*(vu_long *) MPC5XXX_SDRAM_CTRL =
|
|
SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* set mode register: extended mode */
|
|
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* set mode register: reset DLL */
|
|
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* precharge all banks */
|
|
*(vu_long *) MPC5XXX_SDRAM_CTRL =
|
|
SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* auto refresh */
|
|
*(vu_long *) MPC5XXX_SDRAM_CTRL =
|
|
SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* set mode register */
|
|
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* normal operation */
|
|
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
|
|
__asm__ volatile ("sync");
|
|
}
|
|
|
|
/*
|
|
* ATTENTION: Although partially referenced initdram does NOT make real use
|
|
* use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
|
|
* is something else than 0x00000000.
|
|
*/
|
|
|
|
phys_size_t initdram(int board_type)
|
|
{
|
|
ulong dramsize = 0;
|
|
ulong test1, test2;
|
|
|
|
/* setup SDRAM chip selects */
|
|
*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
|
|
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
|
|
__asm__ volatile ("sync");
|
|
|
|
/* setup config registers */
|
|
*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
|
|
*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* set tap delay */
|
|
*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
|
|
__asm__ volatile ("sync");
|
|
|
|
/* find RAM size using SDRAM CS0 only */
|
|
sdram_start(0);
|
|
test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
|
|
sdram_start(1);
|
|
test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
|
|
|
|
if (test1 > test2) {
|
|
sdram_start(0);
|
|
dramsize = test1;
|
|
} else {
|
|
dramsize = test2;
|
|
}
|
|
|
|
/* memory smaller than 1MB is impossible */
|
|
if (dramsize < (1 << 20)) {
|
|
dramsize = 0;
|
|
}
|
|
|
|
/* set SDRAM CS0 size according to the amount of RAM found */
|
|
if (dramsize > 0) {
|
|
*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
|
|
0x13 + __builtin_ffs(dramsize >> 20) - 1;
|
|
/* let SDRAM CS1 start right after CS0 */
|
|
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
|
|
} else {
|
|
#if 0
|
|
*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
|
|
/* let SDRAM CS1 start right after CS0 */
|
|
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e; /* 2G */
|
|
#else
|
|
*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
|
|
0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
|
|
/* let SDRAM CS1 start right after CS0 */
|
|
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e; /* 2G */
|
|
#endif
|
|
}
|
|
|
|
#if 0
|
|
/* find RAM size using SDRAM CS1 only */
|
|
sdram_start(0);
|
|
get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
|
|
sdram_start(1);
|
|
get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
|
|
sdram_start(0);
|
|
#endif
|
|
/* set SDRAM CS1 size according to the amount of RAM found */
|
|
|
|
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
|
|
|
|
init_ata_reset();
|
|
return (dramsize);
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: esd CPCI5200 (cpci5200)\n");
|
|
return 0;
|
|
}
|
|
|
|
void flash_preinit(void)
|
|
{
|
|
/*
|
|
* Now, when we are in RAM, enable flash write
|
|
* access for detection process.
|
|
* Note that CS_BOOT cannot be cleared when
|
|
* executing in flash.
|
|
*/
|
|
*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
|
|
}
|
|
|
|
void flash_afterinit(ulong size)
|
|
{
|
|
if (size == 0x02000000) {
|
|
/* adjust mapping */
|
|
*(vu_long *) MPC5XXX_BOOTCS_START =
|
|
*(vu_long *) MPC5XXX_CS0_START =
|
|
START_REG(CONFIG_SYS_BOOTCS_START | size);
|
|
*(vu_long *) MPC5XXX_BOOTCS_STOP =
|
|
*(vu_long *) MPC5XXX_CS0_STOP =
|
|
STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_PCI
|
|
static struct pci_controller hose;
|
|
|
|
extern void pci_mpc5xxx_init(struct pci_controller *);
|
|
|
|
void pci_init_board(void) {
|
|
pci_mpc5xxx_init(&hose);
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET)
|
|
|
|
void init_ide_reset(void)
|
|
{
|
|
debug("init_ide_reset\n");
|
|
|
|
/* Configure PSC1_4 as GPIO output for ATA reset */
|
|
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
|
|
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
|
|
}
|
|
|
|
void ide_set_reset(int idereset)
|
|
{
|
|
debug("ide_reset(%d)\n", idereset);
|
|
|
|
if (idereset) {
|
|
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
|
|
} else {
|
|
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#define MPC5XXX_SIMPLEIO_GPIO_ENABLE (MPC5XXX_GPIO + 0x0004)
|
|
#define MPC5XXX_SIMPLEIO_GPIO_DIR (MPC5XXX_GPIO + 0x000C)
|
|
#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x0010)
|
|
#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT (MPC5XXX_GPIO + 0x0014)
|
|
|
|
#define MPC5XXX_INTERRUPT_GPIO_ENABLE (MPC5XXX_GPIO + 0x0020)
|
|
#define MPC5XXX_INTERRUPT_GPIO_DIR (MPC5XXX_GPIO + 0x0028)
|
|
#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
|
|
#define MPC5XXX_INTERRUPT_GPIO_STATUS (MPC5XXX_GPIO + 0x003C)
|
|
|
|
#define GPIO_WU6 0x40000000UL
|
|
#define GPIO_USB0 0x00010000UL
|
|
#define GPIO_USB9 0x08000000UL
|
|
#define GPIO_USB9S 0x00080000UL
|
|
|
|
void init_ata_reset(void)
|
|
{
|
|
debug("init_ata_reset\n");
|
|
|
|
/* Configure GPIO_WU6 as GPIO output for ATA reset */
|
|
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
|
|
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
|
|
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
|
|
__asm__ volatile ("sync");
|
|
|
|
*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
|
|
*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
|
|
*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
|
|
__asm__ volatile ("sync");
|
|
|
|
*(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
|
|
*(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
|
|
__asm__ volatile ("sync");
|
|
|
|
if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
|
|
*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
|
|
__asm__ volatile ("sync");
|
|
}
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
return pci_eth_init(bis);
|
|
}
|
|
|
|
int do_writepci(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
|
|
{
|
|
unsigned int addr;
|
|
unsigned int size;
|
|
int i;
|
|
volatile unsigned long *ptr;
|
|
|
|
addr = simple_strtol(argv[1], NULL, 16);
|
|
size = simple_strtol(argv[2], NULL, 16);
|
|
|
|
printf("\nWriting at addr %08x, size %08x.\n", addr, size);
|
|
|
|
while (1) {
|
|
ptr = (volatile unsigned long *)addr;
|
|
for (i = 0; i < (size >> 2); i++) {
|
|
*ptr++ = i;
|
|
}
|
|
|
|
/* Abort if ctrl-c was pressed */
|
|
if (ctrlc()) {
|
|
puts("\nAbort\n");
|
|
return 0;
|
|
}
|
|
putc('.');
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
U_BOOT_CMD(writepci, 3, 1, do_writepci,
|
|
"Write some data to pcibus",
|
|
"<addr> <size>\n"
|
|
""
|
|
);
|