mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 09:30:10 +00:00
3e48d37f48
AM62 StarterKit (SK) board is a low cost, small form factor board designed for TI’s AM625 SoC. It supports the following interfaces: * 2 GB DDR4 RAM * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode * x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display * x1 Headphone Jack * x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port * x1 UHS-1 capable µSD card slot * 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837 * 512 Mbit OSPI flash * x4 UART through UART-USB bridge * XDS110 for onboard JTAG debug using USB * Temperature sensors, user push buttons and LEDs * 40-pin User Expansion Connector * 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO) * 20-pin header for Programmable Realtime Unit (PRU) IO pins * 15-pin CSI header Add basic support for AM62-SK. To keep the changes to minimum. Only UART And SD are supported at the moment. This should serve as good example for adding new board support based on AM62x SoC Schematics: https://www.ti.com/lit/zip/sprr448 Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
140 lines
3.3 KiB
Text
140 lines
3.3 KiB
Text
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* AM625 SK dts file for R5 SPL
|
|
* Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
|
|
*/
|
|
|
|
#include "k3-am625-sk.dts"
|
|
#include "k3-am62x-sk-ddr4-1600MTs.dtsi"
|
|
#include "k3-am62-ddr.dtsi"
|
|
|
|
#include "k3-am625-sk-u-boot.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
remoteproc0 = &sysctrler;
|
|
remoteproc1 = &a53_0;
|
|
serial0 = &wkup_uart0;
|
|
serial3 = &main_uart1;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial2:115200n8";
|
|
tick-timer = &timer1;
|
|
};
|
|
|
|
memory@80000000 {
|
|
device_type = "memory";
|
|
/* 2G RAM */
|
|
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
|
|
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
ranges;
|
|
|
|
secure_ddr: optee@9e800000 {
|
|
reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
|
|
alignment = <0x1000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
a53_0: a53@0 {
|
|
compatible = "ti,am654-rproc";
|
|
reg = <0x00 0x00a90000 0x00 0x10>;
|
|
power-domains = <&k3_pds 61 TI_SCI_PD_EXCLUSIVE>,
|
|
<&k3_pds 135 TI_SCI_PD_EXCLUSIVE>;
|
|
resets = <&k3_reset 135 0>;
|
|
clocks = <&k3_clks 61 0>;
|
|
assigned-clocks = <&k3_clks 61 0>, <&k3_clks 135 0>;
|
|
assigned-clock-parents = <&k3_clks 61 2>;
|
|
assigned-clock-rates = <200000000>, <1200000000>;
|
|
ti,sci = <&dmsc>;
|
|
ti,sci-proc-id = <32>;
|
|
ti,sci-host-id = <10>;
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
dm_tifs: dm-tifs {
|
|
compatible = "ti,j721e-dm-sci";
|
|
ti,host-id = <36>;
|
|
ti,secure-host;
|
|
mbox-names = "rx", "tx";
|
|
mboxes= <&secure_proxy_main 22>,
|
|
<&secure_proxy_main 23>;
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&dmsc {
|
|
mboxes= <&secure_proxy_main 0>,
|
|
<&secure_proxy_main 1>,
|
|
<&secure_proxy_main 0>;
|
|
mbox-names = "rx", "tx", "notify";
|
|
ti,host-id = <35>;
|
|
ti,secure-host;
|
|
};
|
|
|
|
&cbass_main {
|
|
sa3_secproxy: secproxy@44880000 {
|
|
u-boot,dm-spl;
|
|
compatible = "ti,am654-secure-proxy";
|
|
#mbox-cells = <1>;
|
|
reg-names = "rt", "scfg", "target_data";
|
|
reg = <0x00 0x44880000 0x00 0x20000>,
|
|
<0x0 0x44860000 0x0 0x20000>,
|
|
<0x0 0x43600000 0x0 0x10000>;
|
|
};
|
|
|
|
sysctrler: sysctrler {
|
|
compatible = "ti,am654-system-controller";
|
|
mboxes= <&secure_proxy_main 1>, <&secure_proxy_main 0>, <&sa3_secproxy 0>;
|
|
mbox-names = "tx", "rx", "boot_notify";
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&mcu_pmx0 {
|
|
u-boot,dm-spl;
|
|
wkup_uart0_pins_default: wkup-uart0-pins-default {
|
|
pinctrl-single,pins = <
|
|
AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6) WKUP_UART0_CTSn */
|
|
AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4) WKUP_UART0_RTSn */
|
|
AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4) WKUP_UART0_RXD */
|
|
AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5) WKUP_UART0_TXD */
|
|
>;
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&main_pmx0 {
|
|
u-boot,dm-spl;
|
|
main_uart1_pins_default: main-uart1-pins-default {
|
|
pinctrl-single,pins = <
|
|
AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
|
|
AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
|
|
AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
|
|
AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
|
|
>;
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
/* WKUP UART0 is used for DM firmware logs */
|
|
&wkup_uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wkup_uart0_pins_default>;
|
|
status = "okay";
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
/* Main UART1 is used for TIFS firmware logs */
|
|
&main_uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&main_uart1_pins_default>;
|
|
status = "okay";
|
|
u-boot,dm-spl;
|
|
};
|