u-boot/board/nvidia/cardhu/cardhu.c
Simon Glass b0e6ef4640 dm: i2c: tegra: Convert to driver model
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:

   - CONFIG_SYS_I2C_INIT_BOARD
   - CONFIG_I2C_MULTI_BUS
   - CONFIG_SYS_MAX_I2C_BUS
   - CONFIG_SYS_I2C_SPEED
   - CONFIG_SYS_I2C

This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1

It has not been tested on Tegra 114 as I don't have that board.

Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-12-11 13:18:44 -07:00

85 lines
1.7 KiB
C

/*
* (C) Copyright 2010-2013
* NVIDIA Corporation <www.nvidia.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <dm.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/gp_padctrl.h>
#include "pinmux-config-cardhu.h"
#include <i2c.h>
#define PMU_I2C_ADDRESS 0x2D
#define MAX_I2C_RETRY 3
/*
* Routine: pinmux_init
* Description: Do individual peripheral pinmux configs
*/
void pinmux_init(void)
{
pinmux_config_pingrp_table(tegra3_pinmux_common,
ARRAY_SIZE(tegra3_pinmux_common));
pinmux_config_pingrp_table(unused_pins_lowpower,
ARRAY_SIZE(unused_pins_lowpower));
/* Initialize any non-default pad configs (APB_MISC_GP regs) */
pinmux_config_drvgrp_table(cardhu_padctrl, ARRAY_SIZE(cardhu_padctrl));
}
#if defined(CONFIG_TEGRA_MMC)
/*
* Do I2C/PMU writes to bring up SD card bus power
*
*/
void board_sdmmc_voltage_init(void)
{
struct udevice *dev;
uchar reg, data_buffer[1];
int ret;
int i;
ret = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, &dev);
if (ret) {
debug("%s: Cannot find PMIC I2C chip\n", __func__);
return;
}
/* TPS659110: LDO5_REG = 3.3v, ACTIVE to SDMMC1 */
data_buffer[0] = 0x65;
reg = 0x32;
for (i = 0; i < MAX_I2C_RETRY; ++i) {
if (i2c_write(dev, reg, data_buffer, 1))
udelay(100);
}
/* TPS659110: GPIO7_REG = PDEN, output a 1 to EN_3V3_SYS */
data_buffer[0] = 0x09;
reg = 0x67;
for (i = 0; i < MAX_I2C_RETRY; ++i) {
if (i2c_write(dev, reg, data_buffer, 1))
udelay(100);
}
}
/*
* Routine: pin_mux_mmc
* Description: setup the MMC muxes, power rails, etc.
*/
void pin_mux_mmc(void)
{
/*
* NOTE: We don't do mmc-specific pin muxes here.
* They were done globally in pinmux_init().
*/
/* Bring up the SDIO1 power rail */
board_sdmmc_voltage_init();
}
#endif /* MMC */