mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
a187559e3d
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
127 lines
5.3 KiB
Text
127 lines
5.3 KiB
Text
|
|
|
|
U-Boot for Wind River SBC834x Boards
|
|
====================================
|
|
|
|
|
|
The Wind River SBC834x board is a 6U form factor (not CPCI) reference
|
|
design that uses the MPC8347E or MPC8349E processor. U-Boot support
|
|
for this board is heavily based on the existing U-Boot support for
|
|
Freescale MPC8349 reference boards.
|
|
|
|
Support has been primarily tested on the SBC8349 version of the board,
|
|
although earlier versions were also tested on the SBC8347. The primary
|
|
difference in the two is the level of PCI functionality.
|
|
|
|
http://www.windriver.com/products/OCD/SBC8347E_49E/
|
|
|
|
|
|
Flash Details:
|
|
==============
|
|
|
|
The flash type is intel 28F640Jx (4096x16) [one device]. Base address
|
|
is 0xFF80_0000 which is also where the Hardware Reset Configuration
|
|
Word (HRCW) is stored. Caution should be used to not reset the
|
|
board without having a valid HRCW in place (i.e. erased flash) as
|
|
then a Wind River ICE will be required to restore the HRCW and flash
|
|
image.
|
|
|
|
|
|
Restoring a corrupted or missing flash image:
|
|
=============================================
|
|
|
|
Note that U-Boot versions up to and including 2009.06 had essentially
|
|
two copies of U-Boot in flash; one at the very beginning, which set
|
|
the HRCW, and one at the very end, which was the image that was run.
|
|
As of this point in time, the two have been combined into just one
|
|
at the beginning of flash, which provides both the HRCW, and the image
|
|
that is executed. This frees up the remainder of flash for other uses.
|
|
Use of the U-Boot command "fli" will indicate what parts are in use.
|
|
Details for storing U-Boot to flash using a Wind River ICE can be found
|
|
on page 19 of the board manual (request ERG-00328-001). The following
|
|
is a summary of that information:
|
|
|
|
- Connect ICE and establish connection to it from WorkBench/OCD.
|
|
- Ensure you have background mode (BKM) in the OCD terminal window.
|
|
- Select the appropriate flash type (listed above)
|
|
- Prepare a U-Boot image by using the Wind River Convert utility;
|
|
by using "Convert and Add file" on the ELF file from your build.
|
|
Convert from FF80_0000 to FFFF_FFFF (or to FF83_FFFF if you are
|
|
trying to preserve your old environment settings and user flash).
|
|
- Set the start address of the erase/flash process to FF80_0000
|
|
- Set the target RAM required to 64kB.
|
|
- Select sectors for erasing (see note on environment below)
|
|
- Select Erase and Reprogram.
|
|
|
|
Note that some versions of the register files used with Workbench
|
|
would zero some TSEC registers, which inhibits ethernet operation
|
|
by U-Boot when this register file is played to the target. Using
|
|
"INN" in the OCD terminal window instead of "IN" before the "GO"
|
|
will not play the register file, and allow U-Boot to use the TSEC
|
|
interface while executed from the ICE "GO" command.
|
|
|
|
Alternatively, you can locate the register file which will be named
|
|
WRS_SBC8349_PCT00328001.reg or similar) and "REM" out all the lines
|
|
beginning with "SCGA TSEC1" and "SCGA TSEC2". This allows you to
|
|
use all the remaining register file content.
|
|
|
|
If you wish to preserve your prior U-Boot environment settings,
|
|
then convert (and erase to) 0xFF83FFFF instead of 0xFFFFFFFF.
|
|
The size for converting (and erasing) must be at least as large
|
|
as u-boot.bin.
|
|
|
|
|
|
Updating U-Boot with U-Boot:
|
|
============================
|
|
|
|
This procedure is very similar to other boards that have U-Boot installed.
|
|
Assuming that the network has been configured, and that the new u-boot.bin
|
|
has been copied to the TFTP server, the commands are:
|
|
|
|
tftp 200000 u-boot.bin
|
|
protect off all
|
|
erase ff800000 ff83ffff
|
|
cp.b 200000 ff800000 40000
|
|
protect on all
|
|
|
|
You may wish to do a "md ff800000 20" operation as a prefix and postfix
|
|
to the above steps to inspect/compare the HRCW before/after as an extra
|
|
safety check before resetting the board upon completion of the reflash.
|
|
|
|
PCI:
|
|
====
|
|
|
|
There are three configuration choices:
|
|
sbc8349_config
|
|
sbc8349_PCI_33_config
|
|
sbc8349_PCI_66_config
|
|
|
|
The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
|
|
will be left empty (M66EN high), and so the board will operate with
|
|
a base clock of 66MHz. Note that you need both PCI enabled in U-Boot
|
|
and linux in order to have functional PCI under linux. The only
|
|
reason for choosing to not enable PCI would be if you had a very
|
|
early (rev 1.0) CPU with possible PCI issues.
|
|
|
|
The second enables PCI support and builds for a 33MHz clock rate. Note
|
|
that if a 33MHz 32bit card is inserted in the slot, then the whole board
|
|
will clock down to a 33MHz base clock instead of the default 66MHz. This
|
|
will change the baud clocks and mess up your serial console output if you
|
|
were previously running at 66MHz. If you want to use a 33MHz PCI card,
|
|
then you should build a U-Boot with sbc8349_PCI_33_config and store this
|
|
to flash prior to powering down the board and inserting the 33MHz PCI
|
|
card.
|
|
|
|
The third option builds PCI support in, and leaves the clocking at the
|
|
default 66MHz. This has been tested with an intel PCI-X e1000 card.
|
|
This is also the appropriate choice for people with a recent (non 1.0)
|
|
CPU who currently have the PCI slot physically empty, but intend to
|
|
possibly add a PCI-X card at a later date.
|
|
|
|
=> pci
|
|
Scanning PCI devices on bus 0
|
|
BusDevFun VendorId DeviceId Device Class Sub-Class
|
|
_____________________________________________________________
|
|
00.00.00 0x1957 0x0080 Processor 0x20
|
|
00.11.00 0x8086 0x1026 Network controller 0x00
|
|
=>
|