u-boot/board/qi/qi_lb60/qi_lb60.c
Xiangfu Liu 3c945542da MIPS: Jz4740: Add qi_lb60 board support
Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:

http://en.qi-hardware.com/wiki/Ben_NanoNote
http://en.qi-hardware.com/wiki/Main_Page
http://en.wikipedia.org/wiki/Qi_hardware

This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.

About USB boot tool
-------------------

Jz4740 is one of the XBurst processors with USB boot functionality
supported.  The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.

USB boot tool is available to the public at Ingenic website.  Also
there is an alternative Debian package named xburst-tools.

Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-10-12 23:28:49 +09:00

104 lines
2.1 KiB
C

/*
* Authors: Xiangfu Liu <xiangfu@sharism.cc>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 3 of the License, or (at your option) any later version.
*/
#include <common.h>
#include <asm/io.h>
#include <asm/jz4740.h>
DECLARE_GLOBAL_DATA_PTR;
static void gpio_init(void)
{
unsigned int i;
/* Initialize NAND Flash Pins */
__gpio_as_nand();
/* Initialize SDRAM pins */
__gpio_as_sdram_16bit_4720();
/* Initialize LCD pins */
__gpio_as_lcd_18bit();
/* Initialize MSC pins */
__gpio_as_msc();
/* Initialize Other pins */
for (i = 0; i < 7; i++) {
__gpio_as_input(GPIO_KEYIN_BASE + i);
__gpio_enable_pull(GPIO_KEYIN_BASE + i);
}
for (i = 0; i < 8; i++) {
__gpio_as_output(GPIO_KEYOUT_BASE + i);
__gpio_clear_pin(GPIO_KEYOUT_BASE + i);
}
__gpio_as_input(GPIO_KEYIN_8);
__gpio_enable_pull(GPIO_KEYIN_8);
/* enable the TP4, TP5 as UART0 */
__gpio_jtag_to_uart0();
__gpio_as_output(GPIO_AUDIO_POP);
__gpio_set_pin(GPIO_AUDIO_POP);
__gpio_as_output(GPIO_LCD_CS);
__gpio_clear_pin(GPIO_LCD_CS);
__gpio_as_output(GPIO_AMP_EN);
__gpio_clear_pin(GPIO_AMP_EN);
__gpio_as_output(GPIO_SDPW_EN);
__gpio_disable_pull(GPIO_SDPW_EN);
__gpio_clear_pin(GPIO_SDPW_EN);
__gpio_as_input(GPIO_SD_DETECT);
__gpio_disable_pull(GPIO_SD_DETECT);
__gpio_as_input(GPIO_USB_DETECT);
__gpio_enable_pull(GPIO_USB_DETECT);
}
static void cpm_init(void)
{
struct jz4740_cpm *cpm = (struct jz4740_cpm *)JZ4740_CPM_BASE;
uint32_t reg = readw(&cpm->clkgr);
reg |= CPM_CLKGR_IPU |
CPM_CLKGR_CIM |
CPM_CLKGR_I2C |
CPM_CLKGR_SSI |
CPM_CLKGR_UART1 |
CPM_CLKGR_SADC |
CPM_CLKGR_UHC |
CPM_CLKGR_UDC |
CPM_CLKGR_AIC1;
writew(reg, &cpm->clkgr);
}
int board_early_init_f(void)
{
gpio_init();
cpm_init();
calc_clocks(); /* calc the clocks */
rtc_init(); /* init rtc on any reset */
return 0;
}
/* U-Boot common routines */
int checkboard(void)
{
printf("Board: Qi LB60 (Ingenic XBurst Jz4740 SoC, Speed %ld MHz)\n",
gd->cpu_clk / 1000000);
return 0;
}