u-boot/arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts
Marek Vasut 1a6de002e5 ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-01-06 11:01:31 +01:00

93 lines
1.7 KiB
Text

// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
*/
#include "stm32mp15xx-dhcom.dtsi"
/ {
model = "DH Electronics STM32MP15xx DHCOM PicoITX";
compatible = "dh,stm32mp15xx-dhcom-picoitx", "st,stm32mp1xx";
aliases {
serial0 = &uart4;
serial1 = &usart3;
serial2 = &uart8;
};
chosen {
stdout-path = "serial0:115200n8";
};
};
&adc {
status = "disabled";
};
&dac {
status = "disabled";
};
&gpioa {
/*
* NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
* port power. This signal should be handled by USB power sequencing
* in order to turn on port power when USB bus is powered up, but so
* far there is no such functionality.
*/
usb-port-power {
gpio-hog;
gpios = <13 0>;
output-low;
line-name = "usb-port-power";
};
};
&i2c2 { /* On board-to-board connector (optional) */
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
};
&i2c5 { /* On board-to-board connector */
pinctrl-names = "default";
pinctrl-0 = <&i2c5_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
};
&usart3 {
pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>;
status = "okay";
};
&uart8 {
pinctrl-names = "default";
pinctrl-0 = <&uart8_pins_a>;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};