mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 13:56:30 +00:00
a40fe217d1
The 'u-boot,i2c-transaction-bytes' device tree property provides information regarding number of bytes transferred by a device in a single transaction. This change is necessary to avoid hanging devices after soft reset. One notable example is communication with MC34708 device: 1. Reset when communicating with MC34708 via I2C. 2. The u-boot (after reboot -f) tries to setup the I2C and then calls force_idle_bus. In the same time MC34708 still has some data to be sent (as it transfers data in 24 bits chunks). 3. The force_idle_bus() is not able to make the bus idle as 8 SCL clocks may be not enough to have the full transmission. 4. We end up with I2C inconsistency with MC34708. This PMIC device requires 24+ SCL cycles to make finish any pending I2C transmission. Signed-off-by: Lukasz Majewski <lukma@denx.de>
952 lines
26 KiB
C
952 lines
26 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2009 Sergey Kubushyn <ksi@koi8.net>
|
|
* Copyright (C) 2009 - 2013 Heiko Schocher <hs@denx.de>
|
|
* Changes for multibus/multiadapter I2C support.
|
|
*
|
|
* (C) Copyright 2001
|
|
* Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
|
|
*
|
|
* The original I2C interface was
|
|
* (C) 2000 by Paolo Scaffardi (arsenio@tin.it)
|
|
* AIRVENT SAM s.p.a - RIMINI(ITALY)
|
|
* but has been changed substantially.
|
|
*/
|
|
|
|
#ifndef _I2C_H_
|
|
#define _I2C_H_
|
|
|
|
/*
|
|
* For now there are essentially two parts to this file - driver model
|
|
* here at the top, and the older code below (with CONFIG_SYS_I2C being
|
|
* most recent). The plan is to migrate everything to driver model.
|
|
* The driver model structures and API are separate as they are different
|
|
* enough as to be incompatible for compilation purposes.
|
|
*/
|
|
|
|
enum dm_i2c_chip_flags {
|
|
DM_I2C_CHIP_10BIT = 1 << 0, /* Use 10-bit addressing */
|
|
DM_I2C_CHIP_RD_ADDRESS = 1 << 1, /* Send address for each read byte */
|
|
DM_I2C_CHIP_WR_ADDRESS = 1 << 2, /* Send address for each write byte */
|
|
};
|
|
|
|
struct udevice;
|
|
/**
|
|
* struct dm_i2c_chip - information about an i2c chip
|
|
*
|
|
* An I2C chip is a device on the I2C bus. It sits at a particular address
|
|
* and normally supports 7-bit or 10-bit addressing.
|
|
*
|
|
* To obtain this structure, use dev_get_parent_platdata(dev) where dev is
|
|
* the chip to examine.
|
|
*
|
|
* @chip_addr: Chip address on bus
|
|
* @offset_len: Length of offset in bytes. A single byte offset can
|
|
* represent up to 256 bytes. A value larger than 1 may be
|
|
* needed for larger devices.
|
|
* @flags: Flags for this chip (dm_i2c_chip_flags)
|
|
* @emul: Emulator for this chip address (only used for emulation)
|
|
*/
|
|
struct dm_i2c_chip {
|
|
uint chip_addr;
|
|
uint offset_len;
|
|
uint flags;
|
|
#ifdef CONFIG_SANDBOX
|
|
struct udevice *emul;
|
|
bool test_mode;
|
|
#endif
|
|
};
|
|
|
|
/**
|
|
* struct dm_i2c_bus- information about an i2c bus
|
|
*
|
|
* An I2C bus contains 0 or more chips on it, each at its own address. The
|
|
* bus can operate at different speeds (measured in Hz, typically 100KHz
|
|
* or 400KHz).
|
|
*
|
|
* To obtain this structure, use dev_get_uclass_priv(bus) where bus is the
|
|
* I2C bus udevice.
|
|
*
|
|
* @speed_hz: Bus speed in hertz (typically 100000)
|
|
* @max_transaction_bytes: Maximal size of single I2C transfer
|
|
*/
|
|
struct dm_i2c_bus {
|
|
int speed_hz;
|
|
int max_transaction_bytes;
|
|
};
|
|
|
|
/*
|
|
* Not all of these flags are implemented in the U-Boot API
|
|
*/
|
|
enum dm_i2c_msg_flags {
|
|
I2C_M_TEN = 0x0010, /* ten-bit chip address */
|
|
I2C_M_RD = 0x0001, /* read data, from slave to master */
|
|
I2C_M_STOP = 0x8000, /* send stop after this message */
|
|
I2C_M_NOSTART = 0x4000, /* no start before this message */
|
|
I2C_M_REV_DIR_ADDR = 0x2000, /* invert polarity of R/W bit */
|
|
I2C_M_IGNORE_NAK = 0x1000, /* continue after NAK */
|
|
I2C_M_NO_RD_ACK = 0x0800, /* skip the Ack bit on reads */
|
|
I2C_M_RECV_LEN = 0x0400, /* length is first received byte */
|
|
};
|
|
|
|
/**
|
|
* struct i2c_msg - an I2C message
|
|
*
|
|
* @addr: Slave address
|
|
* @flags: Flags (see enum dm_i2c_msg_flags)
|
|
* @len: Length of buffer in bytes, may be 0 for a probe
|
|
* @buf: Buffer to send/receive, or NULL if no data
|
|
*/
|
|
struct i2c_msg {
|
|
uint addr;
|
|
uint flags;
|
|
uint len;
|
|
u8 *buf;
|
|
};
|
|
|
|
/**
|
|
* struct i2c_msg_list - a list of I2C messages
|
|
*
|
|
* This is called i2c_rdwr_ioctl_data in Linux but the name does not seem
|
|
* appropriate in U-Boot.
|
|
*
|
|
* @msg: Pointer to i2c_msg array
|
|
* @nmsgs: Number of elements in the array
|
|
*/
|
|
struct i2c_msg_list {
|
|
struct i2c_msg *msgs;
|
|
uint nmsgs;
|
|
};
|
|
|
|
/**
|
|
* dm_i2c_read() - read bytes from an I2C chip
|
|
*
|
|
* To obtain an I2C device (called a 'chip') given the I2C bus address you
|
|
* can use i2c_get_chip(). To obtain a bus by bus number use
|
|
* uclass_get_device_by_seq(UCLASS_I2C, <bus number>).
|
|
*
|
|
* To set the address length of a devce use i2c_set_addr_len(). It
|
|
* defaults to 1.
|
|
*
|
|
* @dev: Chip to read from
|
|
* @offset: Offset within chip to start reading
|
|
* @buffer: Place to put data
|
|
* @len: Number of bytes to read
|
|
*
|
|
* @return 0 on success, -ve on failure
|
|
*/
|
|
int dm_i2c_read(struct udevice *dev, uint offset, uint8_t *buffer, int len);
|
|
|
|
/**
|
|
* dm_i2c_write() - write bytes to an I2C chip
|
|
*
|
|
* See notes for dm_i2c_read() above.
|
|
*
|
|
* @dev: Chip to write to
|
|
* @offset: Offset within chip to start writing
|
|
* @buffer: Buffer containing data to write
|
|
* @len: Number of bytes to write
|
|
*
|
|
* @return 0 on success, -ve on failure
|
|
*/
|
|
int dm_i2c_write(struct udevice *dev, uint offset, const uint8_t *buffer,
|
|
int len);
|
|
|
|
/**
|
|
* dm_i2c_probe() - probe a particular chip address
|
|
*
|
|
* This can be useful to check for the existence of a chip on the bus.
|
|
* It is typically implemented by writing the chip address to the bus
|
|
* and checking that the chip replies with an ACK.
|
|
*
|
|
* @bus: Bus to probe
|
|
* @chip_addr: 7-bit address to probe (10-bit and others are not supported)
|
|
* @chip_flags: Flags for the probe (see enum dm_i2c_chip_flags)
|
|
* @devp: Returns the device found, or NULL if none
|
|
* @return 0 if a chip was found at that address, -ve if not
|
|
*/
|
|
int dm_i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags,
|
|
struct udevice **devp);
|
|
|
|
/**
|
|
* dm_i2c_reg_read() - Read a value from an I2C register
|
|
*
|
|
* This reads a single value from the given address in an I2C chip
|
|
*
|
|
* @dev: Device to use for transfer
|
|
* @addr: Address to read from
|
|
* @return value read, or -ve on error
|
|
*/
|
|
int dm_i2c_reg_read(struct udevice *dev, uint offset);
|
|
|
|
/**
|
|
* dm_i2c_reg_write() - Write a value to an I2C register
|
|
*
|
|
* This writes a single value to the given address in an I2C chip
|
|
*
|
|
* @dev: Device to use for transfer
|
|
* @addr: Address to write to
|
|
* @val: Value to write (normally a byte)
|
|
* @return 0 on success, -ve on error
|
|
*/
|
|
int dm_i2c_reg_write(struct udevice *dev, uint offset, unsigned int val);
|
|
|
|
/**
|
|
* dm_i2c_xfer() - Transfer messages over I2C
|
|
*
|
|
* This transfers a raw message. It is best to use dm_i2c_reg_read/write()
|
|
* instead.
|
|
*
|
|
* @dev: Device to use for transfer
|
|
* @msg: List of messages to transfer
|
|
* @nmsgs: Number of messages to transfer
|
|
* @return 0 on success, -ve on error
|
|
*/
|
|
int dm_i2c_xfer(struct udevice *dev, struct i2c_msg *msg, int nmsgs);
|
|
|
|
/**
|
|
* dm_i2c_set_bus_speed() - set the speed of a bus
|
|
*
|
|
* @bus: Bus to adjust
|
|
* @speed: Requested speed in Hz
|
|
* @return 0 if OK, -EINVAL for invalid values
|
|
*/
|
|
int dm_i2c_set_bus_speed(struct udevice *bus, unsigned int speed);
|
|
|
|
/**
|
|
* dm_i2c_get_bus_speed() - get the speed of a bus
|
|
*
|
|
* @bus: Bus to check
|
|
* @return speed of selected I2C bus in Hz, -ve on error
|
|
*/
|
|
int dm_i2c_get_bus_speed(struct udevice *bus);
|
|
|
|
/**
|
|
* i2c_set_chip_flags() - set flags for a chip
|
|
*
|
|
* Typically addresses are 7 bits, but for 10-bit addresses you should set
|
|
* flags to DM_I2C_CHIP_10BIT. All accesses will then use 10-bit addressing.
|
|
*
|
|
* @dev: Chip to adjust
|
|
* @flags: New flags
|
|
* @return 0 if OK, -EINVAL if value is unsupported, other -ve value on error
|
|
*/
|
|
int i2c_set_chip_flags(struct udevice *dev, uint flags);
|
|
|
|
/**
|
|
* i2c_get_chip_flags() - get flags for a chip
|
|
*
|
|
* @dev: Chip to check
|
|
* @flagsp: Place to put flags
|
|
* @return 0 if OK, other -ve value on error
|
|
*/
|
|
int i2c_get_chip_flags(struct udevice *dev, uint *flagsp);
|
|
|
|
/**
|
|
* i2c_set_offset_len() - set the offset length for a chip
|
|
*
|
|
* The offset used to access a chip may be up to 4 bytes long. Typically it
|
|
* is only 1 byte, which is enough for chips with 256 bytes of memory or
|
|
* registers. The default value is 1, but you can call this function to
|
|
* change it.
|
|
*
|
|
* @offset_len: New offset length value (typically 1 or 2)
|
|
*/
|
|
int i2c_set_chip_offset_len(struct udevice *dev, uint offset_len);
|
|
|
|
/**
|
|
* i2c_get_offset_len() - get the offset length for a chip
|
|
*
|
|
* @return: Current offset length value (typically 1 or 2)
|
|
*/
|
|
int i2c_get_chip_offset_len(struct udevice *dev);
|
|
|
|
/**
|
|
* i2c_deblock() - recover a bus that is in an unknown state
|
|
*
|
|
* See the deblock() method in 'struct dm_i2c_ops' for full information
|
|
*
|
|
* @bus: Bus to recover
|
|
* @return 0 if OK, -ve on error
|
|
*/
|
|
int i2c_deblock(struct udevice *bus);
|
|
|
|
#ifdef CONFIG_DM_I2C_COMPAT
|
|
/**
|
|
* i2c_probe() - Compatibility function for driver model
|
|
*
|
|
* Calls dm_i2c_probe() on the current bus
|
|
*/
|
|
int i2c_probe(uint8_t chip_addr);
|
|
|
|
/**
|
|
* i2c_read() - Compatibility function for driver model
|
|
*
|
|
* Calls dm_i2c_read() with the device corresponding to @chip_addr, and offset
|
|
* set to @addr. @alen must match the current setting for the device.
|
|
*/
|
|
int i2c_read(uint8_t chip_addr, unsigned int addr, int alen, uint8_t *buffer,
|
|
int len);
|
|
|
|
/**
|
|
* i2c_write() - Compatibility function for driver model
|
|
*
|
|
* Calls dm_i2c_write() with the device corresponding to @chip_addr, and offset
|
|
* set to @addr. @alen must match the current setting for the device.
|
|
*/
|
|
int i2c_write(uint8_t chip_addr, unsigned int addr, int alen, uint8_t *buffer,
|
|
int len);
|
|
|
|
/**
|
|
* i2c_get_bus_num_fdt() - Compatibility function for driver model
|
|
*
|
|
* @return the bus number associated with the given device tree node
|
|
*/
|
|
int i2c_get_bus_num_fdt(int node);
|
|
|
|
/**
|
|
* i2c_get_bus_num() - Compatibility function for driver model
|
|
*
|
|
* @return the 'current' bus number
|
|
*/
|
|
unsigned int i2c_get_bus_num(void);
|
|
|
|
/**
|
|
* i2c_set_bus_num() - Compatibility function for driver model
|
|
*
|
|
* Sets the 'current' bus
|
|
*/
|
|
int i2c_set_bus_num(unsigned int bus);
|
|
|
|
static inline void I2C_SET_BUS(unsigned int bus)
|
|
{
|
|
i2c_set_bus_num(bus);
|
|
}
|
|
|
|
static inline unsigned int I2C_GET_BUS(void)
|
|
{
|
|
return i2c_get_bus_num();
|
|
}
|
|
|
|
/**
|
|
* i2c_init() - Compatibility function for driver model
|
|
*
|
|
* This function does nothing.
|
|
*/
|
|
void i2c_init(int speed, int slaveaddr);
|
|
|
|
/**
|
|
* board_i2c_init() - Compatibility function for driver model
|
|
*
|
|
* @param blob Device tree blbo
|
|
* @return the number of I2C bus
|
|
*/
|
|
void board_i2c_init(const void *blob);
|
|
|
|
/*
|
|
* Compatibility functions for driver model.
|
|
*/
|
|
uint8_t i2c_reg_read(uint8_t addr, uint8_t reg);
|
|
void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val);
|
|
|
|
#endif
|
|
|
|
/**
|
|
* struct dm_i2c_ops - driver operations for I2C uclass
|
|
*
|
|
* Drivers should support these operations unless otherwise noted. These
|
|
* operations are intended to be used by uclass code, not directly from
|
|
* other code.
|
|
*/
|
|
struct dm_i2c_ops {
|
|
/**
|
|
* xfer() - transfer a list of I2C messages
|
|
*
|
|
* @bus: Bus to read from
|
|
* @msg: List of messages to transfer
|
|
* @nmsgs: Number of messages in the list
|
|
* @return 0 if OK, -EREMOTEIO if the slave did not ACK a byte,
|
|
* -ECOMM if the speed cannot be supported, -EPROTO if the chip
|
|
* flags cannot be supported, other -ve value on some other error
|
|
*/
|
|
int (*xfer)(struct udevice *bus, struct i2c_msg *msg, int nmsgs);
|
|
|
|
/**
|
|
* probe_chip() - probe for the presense of a chip address
|
|
*
|
|
* This function is optional. If omitted, the uclass will send a zero
|
|
* length message instead.
|
|
*
|
|
* @bus: Bus to probe
|
|
* @chip_addr: Chip address to probe
|
|
* @chip_flags: Probe flags (enum dm_i2c_chip_flags)
|
|
* @return 0 if chip was found, -EREMOTEIO if not, -ENOSYS to fall back
|
|
* to default probem other -ve value on error
|
|
*/
|
|
int (*probe_chip)(struct udevice *bus, uint chip_addr, uint chip_flags);
|
|
|
|
/**
|
|
* set_bus_speed() - set the speed of a bus (optional)
|
|
*
|
|
* The bus speed value will be updated by the uclass if this function
|
|
* does not return an error. This method is optional - if it is not
|
|
* provided then the driver can read the speed from
|
|
* dev_get_uclass_priv(bus)->speed_hz
|
|
*
|
|
* @bus: Bus to adjust
|
|
* @speed: Requested speed in Hz
|
|
* @return 0 if OK, -EINVAL for invalid values
|
|
*/
|
|
int (*set_bus_speed)(struct udevice *bus, unsigned int speed);
|
|
|
|
/**
|
|
* get_bus_speed() - get the speed of a bus (optional)
|
|
*
|
|
* Normally this can be provided by the uclass, but if you want your
|
|
* driver to check the bus speed by looking at the hardware, you can
|
|
* implement that here. This method is optional. This method would
|
|
* normally be expected to return dev_get_uclass_priv(bus)->speed_hz.
|
|
*
|
|
* @bus: Bus to check
|
|
* @return speed of selected I2C bus in Hz, -ve on error
|
|
*/
|
|
int (*get_bus_speed)(struct udevice *bus);
|
|
|
|
/**
|
|
* set_flags() - set the flags for a chip (optional)
|
|
*
|
|
* This is generally implemented by the uclass, but drivers can
|
|
* check the value to ensure that unsupported options are not used.
|
|
* This method is optional. If provided, this method will always be
|
|
* called when the flags change.
|
|
*
|
|
* @dev: Chip to adjust
|
|
* @flags: New flags value
|
|
* @return 0 if OK, -EINVAL if value is unsupported
|
|
*/
|
|
int (*set_flags)(struct udevice *dev, uint flags);
|
|
|
|
/**
|
|
* deblock() - recover a bus that is in an unknown state
|
|
*
|
|
* I2C is a synchronous protocol and resets of the processor in the
|
|
* middle of an access can block the I2C Bus until a powerdown of
|
|
* the full unit is done. This is because slaves can be stuck
|
|
* waiting for addition bus transitions for a transaction that will
|
|
* never complete. Resetting the I2C master does not help. The only
|
|
* way is to force the bus through a series of transitions to make
|
|
* sure that all slaves are done with the transaction. This method
|
|
* performs this 'deblocking' if support by the driver.
|
|
*
|
|
* This method is optional.
|
|
*/
|
|
int (*deblock)(struct udevice *bus);
|
|
};
|
|
|
|
#define i2c_get_ops(dev) ((struct dm_i2c_ops *)(dev)->driver->ops)
|
|
|
|
/**
|
|
* struct i2c_mux_ops - operations for an I2C mux
|
|
*
|
|
* The current mux state is expected to be stored in the mux itself since
|
|
* it is the only thing that knows how to make things work. The mux can
|
|
* record the current state and then avoid switching unless it is necessary.
|
|
* So select() can be skipped if the mux is already in the correct state.
|
|
* Also deselect() can be made a nop if required.
|
|
*/
|
|
struct i2c_mux_ops {
|
|
/**
|
|
* select() - select one of of I2C buses attached to a mux
|
|
*
|
|
* This will be called when there is no bus currently selected by the
|
|
* mux. This method does not need to deselect the old bus since
|
|
* deselect() will be already have been called if necessary.
|
|
*
|
|
* @mux: Mux device
|
|
* @bus: I2C bus to select
|
|
* @channel: Channel number correponding to the bus to select
|
|
* @return 0 if OK, -ve on error
|
|
*/
|
|
int (*select)(struct udevice *mux, struct udevice *bus, uint channel);
|
|
|
|
/**
|
|
* deselect() - select one of of I2C buses attached to a mux
|
|
*
|
|
* This is used to deselect the currently selected I2C bus.
|
|
*
|
|
* @mux: Mux device
|
|
* @bus: I2C bus to deselect
|
|
* @channel: Channel number correponding to the bus to deselect
|
|
* @return 0 if OK, -ve on error
|
|
*/
|
|
int (*deselect)(struct udevice *mux, struct udevice *bus, uint channel);
|
|
};
|
|
|
|
#define i2c_mux_get_ops(dev) ((struct i2c_mux_ops *)(dev)->driver->ops)
|
|
|
|
/**
|
|
* i2c_get_chip() - get a device to use to access a chip on a bus
|
|
*
|
|
* This returns the device for the given chip address. The device can then
|
|
* be used with calls to i2c_read(), i2c_write(), i2c_probe(), etc.
|
|
*
|
|
* @bus: Bus to examine
|
|
* @chip_addr: Chip address for the new device
|
|
* @offset_len: Length of a register offset in bytes (normally 1)
|
|
* @devp: Returns pointer to new device if found or -ENODEV if not
|
|
* found
|
|
*/
|
|
int i2c_get_chip(struct udevice *bus, uint chip_addr, uint offset_len,
|
|
struct udevice **devp);
|
|
|
|
/**
|
|
* i2c_get_chip_for_busnum() - get a device to use to access a chip on
|
|
* a bus number
|
|
*
|
|
* This returns the device for the given chip address on a particular bus
|
|
* number.
|
|
*
|
|
* @busnum: Bus number to examine
|
|
* @chip_addr: Chip address for the new device
|
|
* @offset_len: Length of a register offset in bytes (normally 1)
|
|
* @devp: Returns pointer to new device if found or -ENODEV if not
|
|
* found
|
|
*/
|
|
int i2c_get_chip_for_busnum(int busnum, int chip_addr, uint offset_len,
|
|
struct udevice **devp);
|
|
|
|
/**
|
|
* i2c_chip_ofdata_to_platdata() - Decode standard I2C platform data
|
|
*
|
|
* This decodes the chip address from a device tree node and puts it into
|
|
* its dm_i2c_chip structure. This should be called in your driver's
|
|
* ofdata_to_platdata() method.
|
|
*
|
|
* @blob: Device tree blob
|
|
* @node: Node offset to read from
|
|
* @spi: Place to put the decoded information
|
|
*/
|
|
int i2c_chip_ofdata_to_platdata(struct udevice *dev, struct dm_i2c_chip *chip);
|
|
|
|
/**
|
|
* i2c_dump_msgs() - Dump a list of I2C messages
|
|
*
|
|
* This may be useful for debugging.
|
|
*
|
|
* @msg: Message list to dump
|
|
* @nmsgs: Number of messages
|
|
*/
|
|
void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs);
|
|
|
|
/**
|
|
* i2c_emul_find() - Find an emulator for an i2c sandbox device
|
|
*
|
|
* This looks at the device's 'emul' phandle
|
|
*
|
|
* @dev: Device to find an emulator for
|
|
* @emulp: Returns the associated emulator, if found *
|
|
* @return 0 if OK, -ENOENT or -ENODEV if not found
|
|
*/
|
|
int i2c_emul_find(struct udevice *dev, struct udevice **emulp);
|
|
|
|
/**
|
|
* i2c_emul_get_device() - Find the device being emulated
|
|
*
|
|
* Given an emulator this returns the associated device
|
|
*
|
|
* @emul: Emulator for the device
|
|
* @return device that @emul is emulating
|
|
*/
|
|
struct udevice *i2c_emul_get_device(struct udevice *emul);
|
|
|
|
#ifndef CONFIG_DM_I2C
|
|
|
|
/*
|
|
* WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING
|
|
*
|
|
* The implementation MUST NOT use static or global variables if the
|
|
* I2C routines are used to read SDRAM configuration information
|
|
* because this is done before the memories are initialized. Limited
|
|
* use of stack-based variables are OK (the initial stack size is
|
|
* limited).
|
|
*
|
|
* WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING
|
|
*/
|
|
|
|
/*
|
|
* Configuration items.
|
|
*/
|
|
#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */
|
|
|
|
#if !defined(CONFIG_SYS_I2C_MAX_HOPS)
|
|
/* no muxes used bus = i2c adapters */
|
|
#define CONFIG_SYS_I2C_DIRECT_BUS 1
|
|
#define CONFIG_SYS_I2C_MAX_HOPS 0
|
|
#define CONFIG_SYS_NUM_I2C_BUSES ll_entry_count(struct i2c_adapter, i2c)
|
|
#else
|
|
/* we use i2c muxes */
|
|
#undef CONFIG_SYS_I2C_DIRECT_BUS
|
|
#endif
|
|
|
|
/* define the I2C bus number for RTC and DTT if not already done */
|
|
#if !defined(CONFIG_SYS_RTC_BUS_NUM)
|
|
#define CONFIG_SYS_RTC_BUS_NUM 0
|
|
#endif
|
|
#if !defined(CONFIG_SYS_SPD_BUS_NUM)
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
#endif
|
|
|
|
struct i2c_adapter {
|
|
void (*init)(struct i2c_adapter *adap, int speed,
|
|
int slaveaddr);
|
|
int (*probe)(struct i2c_adapter *adap, uint8_t chip);
|
|
int (*read)(struct i2c_adapter *adap, uint8_t chip,
|
|
uint addr, int alen, uint8_t *buffer,
|
|
int len);
|
|
int (*write)(struct i2c_adapter *adap, uint8_t chip,
|
|
uint addr, int alen, uint8_t *buffer,
|
|
int len);
|
|
uint (*set_bus_speed)(struct i2c_adapter *adap,
|
|
uint speed);
|
|
int speed;
|
|
int waitdelay;
|
|
int slaveaddr;
|
|
int init_done;
|
|
int hwadapnr;
|
|
char *name;
|
|
};
|
|
|
|
#define U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \
|
|
_set_speed, _speed, _slaveaddr, _hwadapnr, _name) \
|
|
{ \
|
|
.init = _init, \
|
|
.probe = _probe, \
|
|
.read = _read, \
|
|
.write = _write, \
|
|
.set_bus_speed = _set_speed, \
|
|
.speed = _speed, \
|
|
.slaveaddr = _slaveaddr, \
|
|
.init_done = 0, \
|
|
.hwadapnr = _hwadapnr, \
|
|
.name = #_name \
|
|
};
|
|
|
|
#define U_BOOT_I2C_ADAP_COMPLETE(_name, _init, _probe, _read, _write, \
|
|
_set_speed, _speed, _slaveaddr, _hwadapnr) \
|
|
ll_entry_declare(struct i2c_adapter, _name, i2c) = \
|
|
U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \
|
|
_set_speed, _speed, _slaveaddr, _hwadapnr, _name);
|
|
|
|
struct i2c_adapter *i2c_get_adapter(int index);
|
|
|
|
#ifndef CONFIG_SYS_I2C_DIRECT_BUS
|
|
struct i2c_mux {
|
|
int id;
|
|
char name[16];
|
|
};
|
|
|
|
struct i2c_next_hop {
|
|
struct i2c_mux mux;
|
|
uint8_t chip;
|
|
uint8_t channel;
|
|
};
|
|
|
|
struct i2c_bus_hose {
|
|
int adapter;
|
|
struct i2c_next_hop next_hop[CONFIG_SYS_I2C_MAX_HOPS];
|
|
};
|
|
#define I2C_NULL_HOP {{-1, ""}, 0, 0}
|
|
extern struct i2c_bus_hose i2c_bus[];
|
|
|
|
#define I2C_ADAPTER(bus) i2c_bus[bus].adapter
|
|
#else
|
|
#define I2C_ADAPTER(bus) bus
|
|
#endif
|
|
#define I2C_BUS gd->cur_i2c_bus
|
|
|
|
#define I2C_ADAP_NR(bus) i2c_get_adapter(I2C_ADAPTER(bus))
|
|
#define I2C_ADAP I2C_ADAP_NR(gd->cur_i2c_bus)
|
|
#define I2C_ADAP_HWNR (I2C_ADAP->hwadapnr)
|
|
|
|
#ifndef CONFIG_SYS_I2C_DIRECT_BUS
|
|
#define I2C_MUX_PCA9540_ID 1
|
|
#define I2C_MUX_PCA9540 {I2C_MUX_PCA9540_ID, "PCA9540B"}
|
|
#define I2C_MUX_PCA9542_ID 2
|
|
#define I2C_MUX_PCA9542 {I2C_MUX_PCA9542_ID, "PCA9542A"}
|
|
#define I2C_MUX_PCA9544_ID 3
|
|
#define I2C_MUX_PCA9544 {I2C_MUX_PCA9544_ID, "PCA9544A"}
|
|
#define I2C_MUX_PCA9547_ID 4
|
|
#define I2C_MUX_PCA9547 {I2C_MUX_PCA9547_ID, "PCA9547A"}
|
|
#define I2C_MUX_PCA9548_ID 5
|
|
#define I2C_MUX_PCA9548 {I2C_MUX_PCA9548_ID, "PCA9548"}
|
|
#endif
|
|
|
|
#ifndef I2C_SOFT_DECLARATIONS
|
|
# if (defined(CONFIG_AT91RM9200) || \
|
|
defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9261) || \
|
|
defined(CONFIG_AT91SAM9263))
|
|
# define I2C_SOFT_DECLARATIONS at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIOA;
|
|
# else
|
|
# define I2C_SOFT_DECLARATIONS
|
|
# endif
|
|
#endif
|
|
|
|
/*
|
|
* Many boards/controllers/drivers don't support an I2C slave interface so
|
|
* provide a default slave address for them for use in common code. A real
|
|
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
|
|
* support a slave interface.
|
|
*/
|
|
#ifndef CONFIG_SYS_I2C_SLAVE
|
|
#define CONFIG_SYS_I2C_SLAVE 0xfe
|
|
#endif
|
|
|
|
/*
|
|
* Initialization, must be called once on start up, may be called
|
|
* repeatedly to change the speed and slave addresses.
|
|
*/
|
|
#ifdef CONFIG_SYS_I2C_EARLY_INIT
|
|
void i2c_early_init_f(void);
|
|
#endif
|
|
void i2c_init(int speed, int slaveaddr);
|
|
void i2c_init_board(void);
|
|
|
|
#ifdef CONFIG_SYS_I2C
|
|
/*
|
|
* i2c_get_bus_num:
|
|
*
|
|
* Returns index of currently active I2C bus. Zero-based.
|
|
*/
|
|
unsigned int i2c_get_bus_num(void);
|
|
|
|
/*
|
|
* i2c_set_bus_num:
|
|
*
|
|
* Change the active I2C bus. Subsequent read/write calls will
|
|
* go to this one.
|
|
*
|
|
* bus - bus index, zero based
|
|
*
|
|
* Returns: 0 on success, not 0 on failure
|
|
*
|
|
*/
|
|
int i2c_set_bus_num(unsigned int bus);
|
|
|
|
/*
|
|
* i2c_init_all():
|
|
*
|
|
* Initializes all I2C adapters in the system. All i2c_adap structures must
|
|
* be initialized beforehead with function pointers and data, including
|
|
* speed and slaveaddr. Returns 0 on success, non-0 on failure.
|
|
*/
|
|
void i2c_init_all(void);
|
|
|
|
/*
|
|
* Probe the given I2C chip address. Returns 0 if a chip responded,
|
|
* not 0 on failure.
|
|
*/
|
|
int i2c_probe(uint8_t chip);
|
|
|
|
/*
|
|
* Read/Write interface:
|
|
* chip: I2C chip address, range 0..127
|
|
* addr: Memory (register) address within the chip
|
|
* alen: Number of bytes to use for addr (typically 1, 2 for larger
|
|
* memories, 0 for register type devices with only one
|
|
* register)
|
|
* buffer: Where to read/write the data
|
|
* len: How many bytes to read/write
|
|
*
|
|
* Returns: 0 on success, not 0 on failure
|
|
*/
|
|
int i2c_read(uint8_t chip, unsigned int addr, int alen,
|
|
uint8_t *buffer, int len);
|
|
|
|
int i2c_write(uint8_t chip, unsigned int addr, int alen,
|
|
uint8_t *buffer, int len);
|
|
|
|
/*
|
|
* Utility routines to read/write registers.
|
|
*/
|
|
uint8_t i2c_reg_read(uint8_t addr, uint8_t reg);
|
|
|
|
void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val);
|
|
|
|
/*
|
|
* i2c_set_bus_speed:
|
|
*
|
|
* Change the speed of the active I2C bus
|
|
*
|
|
* speed - bus speed in Hz
|
|
*
|
|
* Returns: new bus speed
|
|
*
|
|
*/
|
|
unsigned int i2c_set_bus_speed(unsigned int speed);
|
|
|
|
/*
|
|
* i2c_get_bus_speed:
|
|
*
|
|
* Returns speed of currently active I2C bus in Hz
|
|
*/
|
|
|
|
unsigned int i2c_get_bus_speed(void);
|
|
|
|
#else
|
|
|
|
/*
|
|
* Probe the given I2C chip address. Returns 0 if a chip responded,
|
|
* not 0 on failure.
|
|
*/
|
|
int i2c_probe(uchar chip);
|
|
|
|
/*
|
|
* Read/Write interface:
|
|
* chip: I2C chip address, range 0..127
|
|
* addr: Memory (register) address within the chip
|
|
* alen: Number of bytes to use for addr (typically 1, 2 for larger
|
|
* memories, 0 for register type devices with only one
|
|
* register)
|
|
* buffer: Where to read/write the data
|
|
* len: How many bytes to read/write
|
|
*
|
|
* Returns: 0 on success, not 0 on failure
|
|
*/
|
|
int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len);
|
|
int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len);
|
|
|
|
/*
|
|
* Utility routines to read/write registers.
|
|
*/
|
|
static inline u8 i2c_reg_read(u8 addr, u8 reg)
|
|
{
|
|
u8 buf;
|
|
|
|
#ifdef DEBUG
|
|
printf("%s: addr=0x%02x, reg=0x%02x\n", __func__, addr, reg);
|
|
#endif
|
|
|
|
i2c_read(addr, reg, 1, &buf, 1);
|
|
|
|
return buf;
|
|
}
|
|
|
|
static inline void i2c_reg_write(u8 addr, u8 reg, u8 val)
|
|
{
|
|
#ifdef DEBUG
|
|
printf("%s: addr=0x%02x, reg=0x%02x, val=0x%02x\n",
|
|
__func__, addr, reg, val);
|
|
#endif
|
|
|
|
i2c_write(addr, reg, 1, &val, 1);
|
|
}
|
|
|
|
/*
|
|
* Functions for setting the current I2C bus and its speed
|
|
*/
|
|
|
|
/*
|
|
* i2c_set_bus_num:
|
|
*
|
|
* Change the active I2C bus. Subsequent read/write calls will
|
|
* go to this one.
|
|
*
|
|
* bus - bus index, zero based
|
|
*
|
|
* Returns: 0 on success, not 0 on failure
|
|
*
|
|
*/
|
|
int i2c_set_bus_num(unsigned int bus);
|
|
|
|
/*
|
|
* i2c_get_bus_num:
|
|
*
|
|
* Returns index of currently active I2C bus. Zero-based.
|
|
*/
|
|
|
|
unsigned int i2c_get_bus_num(void);
|
|
|
|
/*
|
|
* i2c_set_bus_speed:
|
|
*
|
|
* Change the speed of the active I2C bus
|
|
*
|
|
* speed - bus speed in Hz
|
|
*
|
|
* Returns: 0 on success, not 0 on failure
|
|
*
|
|
*/
|
|
int i2c_set_bus_speed(unsigned int);
|
|
|
|
/*
|
|
* i2c_get_bus_speed:
|
|
*
|
|
* Returns speed of currently active I2C bus in Hz
|
|
*/
|
|
|
|
unsigned int i2c_get_bus_speed(void);
|
|
#endif /* CONFIG_SYS_I2C */
|
|
|
|
/*
|
|
* only for backwardcompatibility, should go away if we switched
|
|
* completely to new multibus support.
|
|
*/
|
|
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS)
|
|
# if !defined(CONFIG_SYS_MAX_I2C_BUS)
|
|
# define CONFIG_SYS_MAX_I2C_BUS 2
|
|
# endif
|
|
# define I2C_MULTI_BUS 1
|
|
#else
|
|
# define CONFIG_SYS_MAX_I2C_BUS 1
|
|
# define I2C_MULTI_BUS 0
|
|
#endif
|
|
|
|
/* NOTE: These two functions MUST be always_inline to avoid code growth! */
|
|
static inline unsigned int I2C_GET_BUS(void) __attribute__((always_inline));
|
|
static inline unsigned int I2C_GET_BUS(void)
|
|
{
|
|
return I2C_MULTI_BUS ? i2c_get_bus_num() : 0;
|
|
}
|
|
|
|
static inline void I2C_SET_BUS(unsigned int bus) __attribute__((always_inline));
|
|
static inline void I2C_SET_BUS(unsigned int bus)
|
|
{
|
|
if (I2C_MULTI_BUS)
|
|
i2c_set_bus_num(bus);
|
|
}
|
|
|
|
/* Multi I2C definitions */
|
|
enum {
|
|
I2C_0, I2C_1, I2C_2, I2C_3, I2C_4, I2C_5, I2C_6, I2C_7,
|
|
I2C_8, I2C_9, I2C_10,
|
|
};
|
|
|
|
/**
|
|
* Get FDT values for i2c bus.
|
|
*
|
|
* @param blob Device tree blbo
|
|
* @return the number of I2C bus
|
|
*/
|
|
void board_i2c_init(const void *blob);
|
|
|
|
/**
|
|
* Find the I2C bus number by given a FDT I2C node.
|
|
*
|
|
* @param blob Device tree blbo
|
|
* @param node FDT I2C node to find
|
|
* @return the number of I2C bus (zero based), or -1 on error
|
|
*/
|
|
int i2c_get_bus_num_fdt(int node);
|
|
|
|
/**
|
|
* Reset the I2C bus represented by the given a FDT I2C node.
|
|
*
|
|
* @param blob Device tree blbo
|
|
* @param node FDT I2C node to find
|
|
* @return 0 if port was reset, -1 if not found
|
|
*/
|
|
int i2c_reset_port_fdt(const void *blob, int node);
|
|
|
|
#endif /* !CONFIG_DM_I2C */
|
|
|
|
#endif /* _I2C_H_ */
|