u-boot/include/configs/highbank.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

66 lines
1.7 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2010-2011 Calxeda, Inc.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
#define CONFIG_SYS_TIMER_RATE (150000000/256)
#define CONFIG_SYS_TIMER_COUNTER (0xFFF34000 + 0x4)
#define CONFIG_SYS_TIMER_COUNTS_DOWN
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
#define CONFIG_PL011_CLOCK 150000000
#define CONFIG_PL01x_PORTS { (void *)(0xFFF36000) }
#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 5
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_CALXEDA_XGMAC
/*
* Command line configuration.
*/
#define CONFIG_BOOT_RETRY_TIME -1
#define CONFIG_RESET_TO_RETRY
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR 0x800000
#define CONFIG_SYS_64BIT_LBA
/*-----------------------------------------------------------------------
* Physical Memory Map
* The DRAM is already setup, so do not touch the DT node later.
*/
#define PHYS_SDRAM_1_SIZE (4089 << 20)
#define CONFIG_SYS_MEMTEST_START 0x100000
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1_SIZE - 0x100000)
/* Environment data setup
*/
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfff88000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE 0x8000 /* NVRAM size */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_INIT_SP_ADDR 0x01000000
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif