mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-27 05:23:34 +00:00
873960c89e
Cloned from the Linux driver v4.2.0-rc2. Plus some patches from Antoine Tenart enabling controller initialization and ONFI timing support: http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html Please note that this driver needs the Linux NAND subsystem sync to v4.1 from Scott to be applied: https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html Otherwise it will not compile. Tested on the Marvell Armada XP DB-MV784MP-GP eval board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Antoine Tenart <antoine.tenart@free-electrons.com> Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Scott Wood <scottwood@freescale.com>
64 lines
2 KiB
C
64 lines
2 KiB
C
#ifndef __ASM_ARCH_PXA3XX_NAND_H
|
|
#define __ASM_ARCH_PXA3XX_NAND_H
|
|
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/partitions.h>
|
|
|
|
struct pxa3xx_nand_timing {
|
|
unsigned int tCH; /* Enable signal hold time */
|
|
unsigned int tCS; /* Enable signal setup time */
|
|
unsigned int tWH; /* ND_nWE high duration */
|
|
unsigned int tWP; /* ND_nWE pulse time */
|
|
unsigned int tRH; /* ND_nRE high duration */
|
|
unsigned int tRP; /* ND_nRE pulse width */
|
|
unsigned int tR; /* ND_nWE high to ND_nRE low for read */
|
|
unsigned int tWHR; /* ND_nWE high to ND_nRE low for status read */
|
|
unsigned int tAR; /* ND_ALE low to ND_nRE low delay */
|
|
};
|
|
|
|
struct pxa3xx_nand_flash {
|
|
uint32_t chip_id;
|
|
unsigned int flash_width; /* Width of Flash memory (DWIDTH_M) */
|
|
unsigned int dfc_width; /* Width of flash controller(DWIDTH_C) */
|
|
struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
|
|
};
|
|
|
|
/*
|
|
* Current pxa3xx_nand controller has two chip select which
|
|
* both be workable.
|
|
*
|
|
* Notice should be taken that:
|
|
* When you want to use this feature, you should not enable the
|
|
* keep configuration feature, for two chip select could be
|
|
* attached with different nand chip. The different page size
|
|
* and timing requirement make the keep configuration impossible.
|
|
*/
|
|
|
|
/* The max num of chip select current support */
|
|
#define NUM_CHIP_SELECT (2)
|
|
struct pxa3xx_nand_platform_data {
|
|
/* the data flash bus is shared between the Static Memory
|
|
* Controller and the Data Flash Controller, the arbiter
|
|
* controls the ownership of the bus
|
|
*/
|
|
int enable_arbiter;
|
|
|
|
/* allow platform code to keep OBM/bootloader defined NFC config */
|
|
int keep_config;
|
|
|
|
/* indicate how many chip selects will be used */
|
|
int num_cs;
|
|
|
|
/* use an flash-based bad block table */
|
|
bool flash_bbt;
|
|
|
|
/* requested ECC strength and ECC step size */
|
|
int ecc_strength, ecc_step_size;
|
|
|
|
const struct mtd_partition *parts[NUM_CHIP_SELECT];
|
|
unsigned int nr_parts[NUM_CHIP_SELECT];
|
|
|
|
const struct pxa3xx_nand_flash *flash;
|
|
size_t num_flash;
|
|
};
|
|
#endif /* __ASM_ARCH_PXA3XX_NAND_H */
|