mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
e91907a146
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
559 lines
19 KiB
C
559 lines
19 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* Copyright 2007-2011 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
/*
|
|
* MPC8610HPCD board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <linux/stringify.h>
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
|
|
|
|
/* video */
|
|
#define CONFIG_FSL_DIU_FB
|
|
|
|
#ifdef CONFIG_FSL_DIU_FB
|
|
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x2c000)
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_VIDEO_BMP_LOGO
|
|
#endif
|
|
|
|
#ifdef RUN_DIAG
|
|
#define CONFIG_SYS_DIAG_ADDR 0xff800000
|
|
#endif
|
|
|
|
/*
|
|
* virtual address to be used for temporary mappings. There
|
|
* should be 128k free at this VA.
|
|
*/
|
|
#define CONFIG_SYS_SCRATCH_VA 0xc0000000
|
|
|
|
#define CONFIG_PCI1 1 /* PCI controller 1 */
|
|
#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
|
|
#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
|
|
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
|
|
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
|
|
|
|
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
|
|
|
|
#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
|
|
#define CONFIG_ALTIVEC 1
|
|
|
|
/*
|
|
* L2CR setup -- make sure this is right for your board!
|
|
*/
|
|
#define CONFIG_SYS_L2
|
|
#define L2_INIT 0
|
|
#define L2_ENABLE (L2CR_L2E |0x00100000 )
|
|
|
|
#ifndef CONFIG_SYS_CLK_FREQ
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
|
|
#endif
|
|
|
|
/*
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*/
|
|
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
|
|
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
|
|
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
|
|
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
|
|
|
|
/* DDR Setup */
|
|
#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
|
|
#define CONFIG_DDR_SPD
|
|
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
|
|
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
|
|
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
|
|
#define CONFIG_VERY_BIG_RAM
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
|
|
|
|
#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
|
|
|
|
/* These are used when DDR doesn't use SPD. */
|
|
#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */
|
|
|
|
#if 0 /* TODO */
|
|
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
|
|
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
|
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
|
|
#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
|
|
#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
|
|
#define CONFIG_SYS_DDR_MODE_1 0x00480432
|
|
#define CONFIG_SYS_DDR_MODE_2 0x00000000
|
|
#define CONFIG_SYS_DDR_INTERVAL 0x06180100
|
|
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
|
|
#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
|
|
#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
|
|
#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
|
|
#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
|
|
#define CONFIG_SYS_DDR_CONTROL2 0x04400010
|
|
|
|
#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
|
|
#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
|
|
#define CONFIG_SYS_DDR_SBE 0x000f0000
|
|
|
|
#endif
|
|
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
|
|
#define CONFIG_SYS_FLASH_BASE2 0xf8000000
|
|
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */
|
|
#define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
|
|
|
|
#define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */
|
|
#define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
|
|
#if 0 /* TODO */
|
|
#define CONFIG_SYS_BR2_PRELIM 0xf0000000
|
|
#define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
|
|
#endif
|
|
#define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */
|
|
#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
|
|
|
|
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
|
|
#define PIXIS_BASE 0xe8000000 /* PIXIS registers */
|
|
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
|
|
#define PIXIS_VER 0x1 /* Board version at offset 1 */
|
|
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
|
|
#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
|
|
#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */
|
|
#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
|
|
#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/
|
|
#define PIXIS_VCTL 0x10 /* VELA Control Register */
|
|
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
|
|
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
|
|
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
|
|
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
|
|
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
|
|
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
|
|
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
|
|
#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xC0 /* Reset altbank mask */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#else
|
|
#undef CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#if defined(CONFIG_SYS_RAMBOOT)
|
|
#undef CONFIG_SPD_EEPROM
|
|
#define CONFIG_SYS_SDRAM_SIZE 256
|
|
#endif
|
|
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#ifndef CONFIG_SYS_INIT_RAM_LOCK
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
|
|
#else
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
|
|
#endif
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
|
|
|
|
/* Serial Port */
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
|
|
|
|
/* maximum size of the flat tree (8K) */
|
|
#define OF_FLAT_TREE_MAX_SIZE 8192
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
|
|
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
|
|
#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS
|
|
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI1_IO_BUS 0x0000000
|
|
#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
|
|
#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
|
|
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
/* controller 1, Base address 0xa000 */
|
|
#define CONFIG_SYS_PCIE1_NAME "ULI"
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
/* controller 2, Base Address 0x9000 */
|
|
#define CONFIG_SYS_PCIE2_NAME "Slot 1"
|
|
#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 /* reuse mem LAW */
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
#if defined(CONFIG_PCI)
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
|
|
#define CONFIG_ULI526X
|
|
|
|
/************************************************************
|
|
* USB support
|
|
************************************************************/
|
|
#define CONFIG_PCI_OHCI 1
|
|
#define CONFIG_USB_OHCI_NEW 1
|
|
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
|
|
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
|
|
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
|
|
|
|
#if !defined(CONFIG_PCI_PNP)
|
|
#define PCI_ENET0_IOADDR 0xe0000000
|
|
#define PCI_ENET0_MEMADDR 0xe0000000
|
|
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
|
|
#endif
|
|
|
|
#ifdef CONFIG_SCSI_AHCI
|
|
#define CONFIG_SATA_ULI5288
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
|
|
#endif
|
|
|
|
#endif /* CONFIG_PCI */
|
|
|
|
/*
|
|
* BAT0 2G Cacheable, non-guarded
|
|
* 0x0000_0000 2G DDR
|
|
*/
|
|
#define CONFIG_SYS_DBAT0L (BATL_PP_RW)
|
|
#define CONFIG_SYS_IBAT0L (BATL_PP_RW)
|
|
|
|
/*
|
|
* BAT1 1G Cache-inhibited, guarded
|
|
* 0x8000_0000 256M PCI-1 Memory
|
|
* 0xa000_0000 256M PCI-Express 1 Memory
|
|
* 0x9000_0000 256M PCI-Express 2 Memory
|
|
*/
|
|
|
|
#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
|
|
|
|
/*
|
|
* BAT2 16M Cache-inhibited, guarded
|
|
* 0xe100_0000 1M PCI-1 I/O
|
|
*/
|
|
|
|
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
|
|
|
|
/*
|
|
* BAT3 4M Cache-inhibited, guarded
|
|
* 0xe000_0000 4M CCSR
|
|
*/
|
|
|
|
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
|
|
|
|
#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
|
|
| BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
|
|
| BATU_BL_1M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
|
|
| BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
|
|
#endif
|
|
|
|
/*
|
|
* BAT4 32M Cache-inhibited, guarded
|
|
* 0xe200_0000 1M PCI-Express 2 I/O
|
|
* 0xe300_0000 1M PCI-Express 1 I/O
|
|
*/
|
|
|
|
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
|
|
|
|
/*
|
|
* BAT5 128K Cacheable, non-guarded
|
|
* 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
|
|
*/
|
|
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
|
|
#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
|
|
|
|
/*
|
|
* BAT6 256M Cache-inhibited, guarded
|
|
* 0xf000_0000 256M FLASH
|
|
*/
|
|
#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
|
|
|
|
/* Map the last 1M of flash where we're running from reset */
|
|
#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
|
|
| BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
|
|
|
|
/*
|
|
* BAT7 4M Cache-inhibited, guarded
|
|
* 0xe800_0000 4M PIXIS
|
|
*/
|
|
#define CONFIG_SYS_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
#define CONFIG_WATCHDOG /* watchdog enabled */
|
|
#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/
|
|
#define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_IPADDR 192.168.1.100
|
|
|
|
#define CONFIG_HOSTNAME "unknown"
|
|
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin
|
|
|
|
#define CONFIG_SERVERIP 192.168.1.1
|
|
#define CONFIG_GATEWAYIP 192.168.1.1
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
|
|
/* default location for tftp and bootm */
|
|
#define CONFIG_LOADADDR 0x10000000
|
|
|
|
#if defined(CONFIG_PCI1)
|
|
#define PCI_ENV \
|
|
"pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
|
|
"echo e;md ${a}e00 9\0" \
|
|
"pci1regs=setenv a e0008; run pcireg\0" \
|
|
"pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
|
|
"pci d.w $b.0 56 1\0" \
|
|
"pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
|
|
"pci w.w $b.0 56 ffff\0" \
|
|
"pci1err=setenv a e0008; run pcierr\0" \
|
|
"pci1errc=setenv a e0008; run pcierrc\0"
|
|
#else
|
|
#define PCI_ENV ""
|
|
#endif
|
|
|
|
#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
|
|
#define PCIE_ENV \
|
|
"pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
|
|
"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
|
|
"pcie1regs=setenv a e000a; run pciereg\0" \
|
|
"pcie2regs=setenv a e0009; run pciereg\0" \
|
|
"pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
|
|
"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
|
|
"pci d $b.0 130 1\0" \
|
|
"pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
|
|
"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
|
|
"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
|
|
"pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
|
|
"pcie1err=setenv a e000a; run pcieerr\0" \
|
|
"pcie2err=setenv a e0009; run pcieerr\0" \
|
|
"pcie1errc=setenv a e000a; run pcieerrc\0" \
|
|
"pcie2errc=setenv a e0009; run pcieerrc\0"
|
|
#else
|
|
#define PCIE_ENV ""
|
|
#endif
|
|
|
|
#define DMA_ENV \
|
|
"dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
|
|
"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
|
|
"dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
|
|
"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
|
|
"dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
|
|
"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
|
|
"dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
|
|
"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
|
|
|
|
#ifdef ENV_DEBUG
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
|
"tftpflash=tftpboot $loadaddr $uboot; " \
|
|
"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
|
|
" +$filesize; " \
|
|
"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
|
|
" +$filesize; " \
|
|
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
|
|
" $filesize; " \
|
|
"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
|
|
" +$filesize; " \
|
|
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
|
|
" $filesize\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=0x18000000\0" \
|
|
"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
|
|
"fdtaddr=0x17c00000\0" \
|
|
"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
|
|
"bdev=sda3\0" \
|
|
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
|
|
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
|
|
"maxcpus=1" \
|
|
"eoi=mw e00400b0 0\0" \
|
|
"iack=md e00400a0 1\0" \
|
|
"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
|
|
"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
|
|
"md ${a}f00 5\0" \
|
|
"ddr1regs=setenv a e0002; run ddrreg\0" \
|
|
"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
|
|
"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
|
|
"md ${a}e60 1; md ${a}ef0 1d\0" \
|
|
"guregs=setenv a e00e0; run gureg\0" \
|
|
"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
|
|
"mcmregs=setenv a e0001; run mcmreg\0" \
|
|
"diuregs=md e002c000 1d\0" \
|
|
"dium=mw e002c01c\0" \
|
|
"diuerr=md e002c014 1\0" \
|
|
"pmregs=md e00e1000 2b\0" \
|
|
"lawregs=md e0000c08 4b\0" \
|
|
"lbcregs=md e0005000 36\0" \
|
|
"dma0regs=md e0021100 12\0" \
|
|
"dma1regs=md e0021180 12\0" \
|
|
"dma2regs=md e0021200 12\0" \
|
|
"dma3regs=md e0021280 12\0" \
|
|
PCI_ENV \
|
|
PCIE_ENV \
|
|
DMA_ENV
|
|
#else
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=0x18000000\0" \
|
|
"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
|
|
"fdtaddr=0x17c00000\0" \
|
|
"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
|
|
"bdev=sda3\0"
|
|
#endif
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"setenv bootargs root=/dev/$bdev rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#endif /* __CONFIG_H */
|