u-boot/board/freescale/t104xrdb/ddr.h
Priyanka Jain 96ac18c9cc powerpc/t104xrdb: Update DDR initialization related settings
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2014-03-07 14:53:48 -08:00

78 lines
1.9 KiB
C

/*
* Copyright 2013 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __DDR_H__
#define __DDR_H__
dimm_params_t ddr_raw_timing = {
.n_ranks = 2,
.rank_density = 2147483648u,
.capacity = 4294967296u,
.primary_sdram_width = 64,
.ec_sdram_width = 8,
.registered_dimm = 0,
.mirrored_dimm = 0,
.n_row_addr = 15,
.n_col_addr = 10,
.n_banks_per_sdram_device = 8,
.edc_config = 2, /* ECC */
.burst_lengths_bitmask = 0x0c,
.tckmin_x_ps = 1071,
.caslat_x = 0xfe << 4, /* 5,6,7,8,9,10,11 */
.taa_ps = 13125,
.twr_ps = 15000,
.trcd_ps = 13125,
.trrd_ps = 6000,
.trp_ps = 13125,
.tras_ps = 34000,
.trc_ps = 48125,
.trfc_ps = 260000,
.twtr_ps = 7500,
.trtp_ps = 7500,
.refresh_rate_ps = 7800000,
.tfaw_ps = 35000,
};
struct board_specific_parameters {
u32 n_ranks;
u32 datarate_mhz_high;
u32 rank_gb;
u32 clk_adjust;
u32 wrlvl_start;
u32 wrlvl_ctl_2;
u32 wrlvl_ctl_3;
};
/*
* These tables contain all valid speeds we want to override with board
* specific parameters. datarate_mhz_high values need to be in ascending order
* for each n_ranks group.
*/
static const struct board_specific_parameters udimm0[] = {
/*
* memory controller 0
* num| hi| rank| clk| wrlvl | wrlvl
* ranks| mhz| GB |adjst| start | ctl2
*/
{2, 833, 4, 4, 6, 0x06060607, 0x08080807},
{2, 833, 0, 4, 6, 0x06060607, 0x08080807},
{2, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09},
{2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09},
{2, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A},
{2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A},
{1, 833, 4, 4, 6, 0x06060607, 0x08080807},
{1, 833, 0, 4, 6, 0x06060607, 0x08080807},
{1, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09},
{1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09},
{1, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A},
{1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A},
{}
};
static const struct board_specific_parameters *udimms[] = {
udimm0,
};
#endif