Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-29 16:10:58 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/cpu/mpc83xx/cpu_init.c
Dave Liu 9be39a67c9 mpc83xx: Add support for the display of reset status 
83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10 01:12:03 -05:00

295 lines
8.2 KiB
C
Raw Blame History

/*
* Copyright (C) 2004-2006 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <mpc83xx.h>
#include <ioports.h>
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_QE
extern qe_iop_conf_t qe_iop_conf_tab[];
extern void qe_config_iopin(u8 port, u8 pin, int dir,
int open_drain, int assign);
extern void qe_init(uint qe_base);
extern void qe_reset(void);
static void config_qe_ioports(void)
{
u8 port, pin;
int dir, open_drain, assign;
int i;
for (i = 0; qe_iop_conf_tab[i].assign != QE_IOP_TAB_END; i++) {
port = qe_iop_conf_tab[i].port;
pin = qe_iop_conf_tab[i].pin;
dir = qe_iop_conf_tab[i].dir;
open_drain = qe_iop_conf_tab[i].open_drain;
assign = qe_iop_conf_tab[i].assign;
qe_config_iopin(port, pin, dir, open_drain, assign);
}
}
#endif
/*
* Breathe some life into the CPU...
*
* Set up the memory map,
* initialize a bunch of registers,
* initialize the UPM's
*/
void cpu_init_f (volatile immap_t * im)
{
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET);
/* Clear initial global data */
memset ((void *) gd, 0, sizeof (gd_t));
/* system performance tweaking */
#ifdef CFG_ACR_PIPE_DEP
/* Arbiter pipeline depth */
im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) |
(CFG_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT);
#endif
#ifdef CFG_SPCR_TSEC1EP
/* TSEC1 Emergency priority */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) | (CFG_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
#endif
#ifdef CFG_SPCR_TSEC2EP
/* TSEC2 Emergency priority */
im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) | (CFG_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC1CM
/* TSEC1 clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) | (CFG_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC2CM
/* TSEC2 & I2C1 clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) | (CFG_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC1ON
/* TSEC1 clock switch */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) | (CFG_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC2ON
/* TSEC2 clock switch */
im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) | (CFG_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
#endif
#ifdef CFG_SCCR_USBMPHCM
/* USB MPH clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) | (CFG_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
#endif
#ifdef CFG_SCCR_PCICM
/* PCI & DMA clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) | (CFG_SCCR_PCICM << SCCR_PCICM_SHIFT);
#endif
#ifdef CFG_SCCR_USBDRCM
/* USB DR clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) | (CFG_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
#endif
#ifdef CFG_SCCR_ENCCM
/* Encryption clock mode */
im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) | (CFG_SCCR_ENCCM << SCCR_PCICM_SHIFT);
#endif
#ifdef CFG_ACR_RPTCNT
/* Arbiter repeat count */
im->arbiter.acr = ((im->arbiter.acr & ~(ACR_RPTCNT)) | (CFG_ACR_RPTCNT << ACR_RPTCNT_SHIFT));
#endif
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
gd->reset_status = im->reset.rsr;
im->reset.rsr = ~(RSR_RES);
/*
* RMR - Reset Mode Register
* contains checkstop reset enable (4.6.1.4)
*/
im->reset.rmr = (RMR_CSRE & (1<<RMR_CSRE_SHIFT));
/* LCRR - Clock Ratio Register (10.3.1.16) */
im->lbus.lcrr = CFG_LCRR;
/* Enable Time Base & Decrimenter ( so we will have udelay() )*/
im->sysconf.spcr |= SPCR_TBEN;
/* System General Purpose Register */
#ifdef CFG_SICRH
im->sysconf.sicrh = CFG_SICRH;
#endif
#ifdef CFG_SICRL
im->sysconf.sicrl = CFG_SICRL;
#endif
/* DDR control driver register */
#ifdef CFG_DDRCDR
im->sysconf.ddrcdr = CFG_DDRCDR;
#endif
#ifdef CONFIG_QE
/* Config QE ioports */
config_qe_ioports();
#endif
/*
* Memory Controller:
*/
/* Map banks 0 and 1 to the FLASH banks 0 and 1 at preliminary
* addresses - these have to be modified later when FLASH size
* has been determined
*/
#if defined(CFG_BR0_PRELIM) \
&& defined(CFG_OR0_PRELIM) \
&& defined(CFG_LBLAWBAR0_PRELIM) \
&& defined(CFG_LBLAWAR0_PRELIM)
im->lbus.bank[0].br = CFG_BR0_PRELIM;
im->lbus.bank[0].or = CFG_OR0_PRELIM;
im->sysconf.lblaw[0].bar = CFG_LBLAWBAR0_PRELIM;
im->sysconf.lblaw[0].ar = CFG_LBLAWAR0_PRELIM;
#else
#error CFG_BR0_PRELIM, CFG_OR0_PRELIM, CFG_LBLAWBAR0_PRELIM & CFG_LBLAWAR0_PRELIM must be defined
#endif
#if defined(CFG_BR1_PRELIM) && defined(CFG_OR1_PRELIM)
im->lbus.bank[1].br = CFG_BR1_PRELIM;
im->lbus.bank[1].or = CFG_OR1_PRELIM;
#endif
#if defined(CFG_LBLAWBAR1_PRELIM) && defined(CFG_LBLAWAR1_PRELIM)
im->sysconf.lblaw[1].bar = CFG_LBLAWBAR1_PRELIM;
im->sysconf.lblaw[1].ar = CFG_LBLAWAR1_PRELIM;
#endif
#if defined(CFG_BR2_PRELIM) && defined(CFG_OR2_PRELIM)
im->lbus.bank[2].br = CFG_BR2_PRELIM;
im->lbus.bank[2].or = CFG_OR2_PRELIM;
#endif
#if defined(CFG_LBLAWBAR2_PRELIM) && defined(CFG_LBLAWAR2_PRELIM)
im->sysconf.lblaw[2].bar = CFG_LBLAWBAR2_PRELIM;
im->sysconf.lblaw[2].ar = CFG_LBLAWAR2_PRELIM;
#endif
#if defined(CFG_BR3_PRELIM) && defined(CFG_OR3_PRELIM)
im->lbus.bank[3].br = CFG_BR3_PRELIM;
im->lbus.bank[3].or = CFG_OR3_PRELIM;
#endif
#if defined(CFG_LBLAWBAR3_PRELIM) && defined(CFG_LBLAWAR3_PRELIM)
im->sysconf.lblaw[3].bar = CFG_LBLAWBAR3_PRELIM;
im->sysconf.lblaw[3].ar = CFG_LBLAWAR3_PRELIM;
#endif
#if defined(CFG_BR4_PRELIM) && defined(CFG_OR4_PRELIM)
im->lbus.bank[4].br = CFG_BR4_PRELIM;
im->lbus.bank[4].or = CFG_OR4_PRELIM;
#endif
#if defined(CFG_LBLAWBAR4_PRELIM) && defined(CFG_LBLAWAR4_PRELIM)
im->sysconf.lblaw[4].bar = CFG_LBLAWBAR4_PRELIM;
im->sysconf.lblaw[4].ar = CFG_LBLAWAR4_PRELIM;
#endif
#if defined(CFG_BR5_PRELIM) && defined(CFG_OR5_PRELIM)
im->lbus.bank[5].br = CFG_BR5_PRELIM;
im->lbus.bank[5].or = CFG_OR5_PRELIM;
#endif
#if defined(CFG_LBLAWBAR5_PRELIM) && defined(CFG_LBLAWAR5_PRELIM)
im->sysconf.lblaw[5].bar = CFG_LBLAWBAR5_PRELIM;
im->sysconf.lblaw[5].ar = CFG_LBLAWAR5_PRELIM;
#endif
#if defined(CFG_BR6_PRELIM) && defined(CFG_OR6_PRELIM)
im->lbus.bank[6].br = CFG_BR6_PRELIM;
im->lbus.bank[6].or = CFG_OR6_PRELIM;
#endif
#if defined(CFG_LBLAWBAR6_PRELIM) && defined(CFG_LBLAWAR6_PRELIM)
im->sysconf.lblaw[6].bar = CFG_LBLAWBAR6_PRELIM;
im->sysconf.lblaw[6].ar = CFG_LBLAWAR6_PRELIM;
#endif
#if defined(CFG_BR7_PRELIM) && defined(CFG_OR7_PRELIM)
im->lbus.bank[7].br = CFG_BR7_PRELIM;
im->lbus.bank[7].or = CFG_OR7_PRELIM;
#endif
#if defined(CFG_LBLAWBAR7_PRELIM) && defined(CFG_LBLAWAR7_PRELIM)
im->sysconf.lblaw[7].bar = CFG_LBLAWBAR7_PRELIM;
im->sysconf.lblaw[7].ar = CFG_LBLAWAR7_PRELIM;
#endif
#ifdef CFG_GPIO1_PRELIM
im->gpio[0].dir = CFG_GPIO1_DIR;
im->gpio[0].dat = CFG_GPIO1_DAT;
#endif
#ifdef CFG_GPIO2_PRELIM
im->gpio[1].dir = CFG_GPIO2_DIR;
im->gpio[1].dat = CFG_GPIO2_DAT;
#endif
}
int cpu_init_r (void)
{
#ifdef CONFIG_QE
uint qe_base = CFG_IMMR + 0x00100000; /* QE immr base */
qe_init(qe_base);
qe_reset();
#endif
return 0;
}
/*
* Figure out the cause of the reset
*/
int prt_83xx_rsr(void)
{
static struct {
ulong mask;
char *desc;
} bits[] = {
{
RSR_SWSR, "Software Soft"}, {
RSR_SWHR, "Software Hard"}, {
RSR_JSRS, "JTAG Soft"}, {
RSR_CSHR, "Check Stop"}, {
RSR_SWRS, "Software Watchdog"}, {
RSR_BMRS, "Bus Monitor"}, {
RSR_SRS, "External/Internal Soft"}, {
RSR_HRS, "External/Internal Hard"}
};
static int n = sizeof bits / sizeof bits[0];
ulong rsr = gd->reset_status;
int i;
char *sep;
puts("Reset Status:");
sep = " ";
for (i = 0; i < n; i++)
if (rsr & bits[i].mask) {
printf("%s%s", sep, bits[i].desc);
sep = ", ";
}
puts("\n\n");
return 0;
}
Reference in a new issue View git blame Copy permalink