mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-28 15:41:40 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
127 lines
3.1 KiB
C
127 lines
3.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2007-2013
|
|
* Stelian Pop <stelian.pop@leadtechdesign.com>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
* Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com>
|
|
* Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_matrix.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm-generic/gpio.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
static void usb_a9263_nand_hw_init(void)
|
|
{
|
|
unsigned long csa;
|
|
at91_smc_t *smc = (at91_smc_t *)ATMEL_BASE_SMC0;
|
|
at91_matrix_t *matrix = (at91_matrix_t *)ATMEL_BASE_MATRIX;
|
|
|
|
/* Enable CS3 */
|
|
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
|
|
writel(csa, &matrix->csa[0]);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
|
|
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
|
|
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
|
|
&smc->cs[3].pulse);
|
|
|
|
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
|
|
&smc->cs[3].cycle);
|
|
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
AT91_SMC_MODE_DBW_8 |
|
|
AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode);
|
|
|
|
at91_periph_clk_enable(ATMEL_ID_PIOA);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOCDE);
|
|
|
|
/* Configure RDY/BSY */
|
|
gpio_request(CONFIG_SYS_NAND_READY_PIN, "NAND ready/busy");
|
|
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
|
|
|
|
/* Enable NandFlash */
|
|
gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "NAND enable");
|
|
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACB
|
|
static void usb_a9263_macb_hw_init(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_EMAC);
|
|
|
|
/*
|
|
* Disable pull-up on:
|
|
* RXDV (PC25) => PHY normal mode (not Test mode)
|
|
* ERX0 (PE25) => PHY ADDR0
|
|
* ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
|
|
*
|
|
* PHY has internal weak pull-up/pull-down
|
|
*/
|
|
gpio_request(GPIO_PIN_PC(25), "PHY mode");
|
|
gpio_direction_input(GPIO_PIN_PC(25));
|
|
|
|
gpio_request(GPIO_PIN_PE(25), "PHY ADDR0");
|
|
gpio_direction_input(GPIO_PIN_PE(25));
|
|
|
|
gpio_request(GPIO_PIN_PE(26), "PHY ADDR1");
|
|
gpio_direction_input(GPIO_PIN_PE(26));
|
|
|
|
at91_phy_reset();
|
|
|
|
/* It will set proper pinmux for ports PC25, PE25-26 */
|
|
at91_macb_hw_init();
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
usb_a9263_nand_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_MACB
|
|
usb_a9263_macb_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_USB_OHCI_NEW
|
|
at91_uhp_hw_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
int rc = 0;
|
|
|
|
#ifdef CONFIG_MACB
|
|
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x0001);
|
|
#endif
|
|
return rc;
|
|
}
|