mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
09f3ca3dd5
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
484 lines
13 KiB
C
484 lines
13 KiB
C
/*
|
|
* (C) Copyright 2003-2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* (C) Copyright 2005-2007
|
|
* Modified for InterControl digsyMTC MPC5200 board by
|
|
* Frank Bodammer, GCD Hard- & Software GmbH,
|
|
* frank.bodammer@gcd-solutions.de
|
|
*
|
|
* (C) Copyright 2009 Semihalf
|
|
* Optimized for digsyMTC by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
|
|
#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
|
|
#define CONFIG_DIGSY_MTC 1 /* ... on InterControl digsyMTC board */
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
|
|
/*
|
|
* Valid values for CONFIG_SYS_TEXT_BASE are:
|
|
* 0xFFF00000 boot high (standard configuration)
|
|
* 0xFE000000 boot low
|
|
* 0x00100000 boot from RAM (for testing only)
|
|
*/
|
|
#ifndef CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32
|
|
|
|
/*
|
|
* Serial console configuration
|
|
*/
|
|
#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 */
|
|
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{ 9600, 19200, 38400, 57600, 115200, 230400 }
|
|
|
|
/*
|
|
* PCI Mapping:
|
|
* 0x40000000 - 0x4fffffff - PCI Memory
|
|
* 0x50000000 - 0x50ffffff - PCI IO Space
|
|
*/
|
|
#define CONFIG_PCI 1
|
|
#define CONFIG_PCI_PNP 1
|
|
#define CONFIG_PCI_SCAN_SHOW 1
|
|
#define CONFIG_PCI_BOOTDELAY 250
|
|
|
|
#define CONFIG_PCI_MEM_BUS 0x40000000
|
|
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
|
|
#define CONFIG_PCI_MEM_SIZE 0x10000000
|
|
|
|
#define CONFIG_PCI_IO_BUS 0x50000000
|
|
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
|
|
#define CONFIG_PCI_IO_SIZE 0x01000000
|
|
|
|
/*
|
|
* Partitions
|
|
*/
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_BZIP2
|
|
|
|
/*
|
|
* Video
|
|
*/
|
|
#define CONFIG_VIDEO
|
|
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_MB862xx
|
|
#define CONFIG_VIDEO_MB862xx_ACCEL
|
|
#define CONFIG_VIDEO_CORALP
|
|
#define CONFIG_CFB_CONSOLE
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_VIDEO_BMP_LOGO
|
|
#define CONFIG_VIDEO_SW_CURSOR
|
|
#define CONFIG_VGA_AS_SINGLE_DEVICE
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
#define CONFIG_SPLASH_SCREEN
|
|
#define CONFIG_VIDEO_BMP_GZIP
|
|
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */
|
|
|
|
/* Coral-PA clock frequency, geo and other both 133MHz */
|
|
#define CONFIG_SYS_MB862xx_CCF 0x00050000
|
|
/* Video SDRAM parameters */
|
|
#define CONFIG_SYS_MB862xx_MMR 0x11d7fa72
|
|
#endif
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_CMD_BMP
|
|
#endif
|
|
#define CONFIG_CMD_CACHE
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DIAG
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_EXT2
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IDE
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_SAVES
|
|
#define CONFIG_CMD_SPI
|
|
#define CONFIG_CMD_USB
|
|
|
|
#if (CONFIG_SYS_TEXT_BASE == 0xFF000000)
|
|
#define CONFIG_SYS_LOWBOOT 1
|
|
#endif
|
|
|
|
/*
|
|
* Autobooting
|
|
*/
|
|
#define CONFIG_BOOTDELAY 1
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"fw_image=digsyMPC.img\0" \
|
|
"mtcb_start=mtc led diag orange; run mtcb_1\0" \
|
|
"mtcb_clearled=for x in user1 user2 usbpwr usbbusy; " \
|
|
"do mtc led $x; done\0" \
|
|
"mtcb_1=if mtc key; then run mtcb_clearled mtcb_update; " \
|
|
"else run mtcb_fw; fi\0" \
|
|
"mtcb_fw=if bootm ff000000; then echo FIRMWARE OK!; " \
|
|
"else echo BAD FIRMWARE CRC!; mtc led diag red; fi\0" \
|
|
"mtcb_update=mtc led user1 orange;" \
|
|
"while mtc key; do ; done; run mtcb_2;\0" \
|
|
"mtcb_2=mtc led user1 green 2; usb reset; run mtcb_usb1;\0" \
|
|
"mtcb_usb1=if fatload usb 0 400000 script.img; " \
|
|
"then run mtcb_doscript; else run mtcb_usb2; fi\0" \
|
|
"mtcb_usb2=if fatload usb 0 400000 $fw_image; " \
|
|
"then run mtcb_dousb; else run mtcb_ide; fi\0" \
|
|
"mtcb_doscript=run mtcb_usbleds; mtc led user2 orange 2; " \
|
|
"run mtcb_wait_flickr mtcb_ds_1;\0" \
|
|
"mtcb_ds_1=if imi 400000; then mtc led usbbusy; " \
|
|
"source 400000; else run mtcb_error; fi\0" \
|
|
"mtcb_dousb=run mtcb_usbleds mtcb_wait_flickr mtcb_du_1;\0" \
|
|
"mtcb_du_1=if imi 400000; then run mtcb_du_2; " \
|
|
"else run mtcb_error; fi\0" \
|
|
"mtcb_du_2=run mtcb_clear mtcb_prog; mtc led usbbusy; " \
|
|
"run mtcb_checkfw\0" \
|
|
"mtcb_checkfw=if imi ff000000; then run mtcb_success; " \
|
|
"else run mtcb_error; fi\0" \
|
|
"mtcb_waitkey=mtc key; until test $? -eq 0; do mtc key; done\0" \
|
|
"mtcb_wait_flickr=run mtcb_waitkey mtcb_uledflckr\0" \
|
|
"mtcb_usbleds=mtc led usbpwr green; mtc led usbbusy orange 1;\0"\
|
|
"mtcb_uledflckr=mtc led user1 orange 11\0" \
|
|
"mtcb_error=mtc led user1 red\0" \
|
|
"mtcb_clear=erase ff000000 ff0fffff\0" \
|
|
"mtcb_prog=cp.b 400000 ff000000 ${filesize}\0" \
|
|
"mtcb_success=mtc led user1 green\0" \
|
|
"mtcb_ide=if fatload ide 0 400000 $fw_image;" \
|
|
"then run mtcb_doide; else run mtcb_error; fi\0" \
|
|
"mtcb_doide=mtc led user2 green 1;" \
|
|
"run mtcb_wait_flickr mtcb_di_1;\0" \
|
|
"mtcb_di_1=if imi 400000; then run mtcb_di_2;" \
|
|
"else run mtcb_error; fi\0" \
|
|
"mtcb_di_2=run mtcb_clear; run mtcb_prog mtcb_checkfw\0" \
|
|
"ramdisk_num_sector=16\0" \
|
|
"flash_base=ff000000\0" \
|
|
"flashdisk_size=e00000\0" \
|
|
"env_sector=fff60000\0" \
|
|
"flashdisk_start=ff100000\0" \
|
|
"load_cmd=tftp 400000 digsyMPC.img\0" \
|
|
"clear_cmd=erase ff000000 ff0fffff\0" \
|
|
"flash_cmd=cp.b 400000 ff000000 ${filesize}\0" \
|
|
"update_cmd=run load_cmd; " \
|
|
"iminfo 400000; " \
|
|
"run clear_cmd flash_cmd; " \
|
|
"iminfo ff000000\0" \
|
|
"spi_driver=yes\0" \
|
|
"spi_watchdog=no\0" \
|
|
"ftps_start=yes\0" \
|
|
"ftps_user1=admin\0" \
|
|
"ftps_pass1=admin\0" \
|
|
"ftps_base1=/\0" \
|
|
"ftps_home1=/\0" \
|
|
"plc_sio_srv=no\0" \
|
|
"plc_sio_baud=57600\0" \
|
|
"plc_sio_parity=no\0" \
|
|
"plc_sio_stop=1\0" \
|
|
"plc_sio_com=2\0" \
|
|
"plc_eth_srv=yes\0" \
|
|
"plc_eth_port=1200\0" \
|
|
"plc_root=/ide/\0" \
|
|
"diag_level=0\0" \
|
|
"webvisu=no\0" \
|
|
"plc_can1_routing=no\0" \
|
|
"plc_can1_baudrate=250\0" \
|
|
"plc_can2_routing=no\0" \
|
|
"plc_can2_baudrate=250\0" \
|
|
"plc_can3_routing=no\0" \
|
|
"plc_can3_baudrate=250\0" \
|
|
"plc_can4_routing=no\0" \
|
|
"plc_can4_baudrate=250\0" \
|
|
"netdev=eth0\0" \
|
|
"console=ttyPSC0\0" \
|
|
"kernel_addr_r=400000\0" \
|
|
"fdt_addr_r=600000\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:" \
|
|
"${netmask}:${hostname}:${netdev}:off panic=1\0" \
|
|
"addcons=setenv bootargs ${bootargs} console=${console},${baudrate}\0"\
|
|
"rootpath=/opt/eldk/ppc_6xx\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
|
|
"tftp ${fdt_addr_r} ${fdt_file};" \
|
|
"run nfsargs addip addcons;" \
|
|
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
|
"load=tftp 200000 ${u-boot}\0" \
|
|
"update=protect off FFF00000 +${filesize};" \
|
|
"erase FFF00000 +${filesize};" \
|
|
"cp.b 200000 FFF00000 ${filesize};" \
|
|
"protect on FFF00000 +${filesize}\0" \
|
|
""
|
|
|
|
#define CONFIG_BOOTCOMMAND "run mtcb_start"
|
|
|
|
/*
|
|
* SPI configuration
|
|
*/
|
|
#define CONFIG_HARD_SPI 1
|
|
#define CONFIG_MPC52XX_SPI 1
|
|
|
|
/*
|
|
* I2C configuration
|
|
*/
|
|
#define CONFIG_HARD_I2C 1
|
|
#define CONFIG_SYS_I2C_MODULE 1
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
/*
|
|
* EEPROM configuration
|
|
*/
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
|
|
|
|
/*
|
|
* RTC configuration
|
|
*/
|
|
#if defined(CONFIG_DIGSY_REV5)
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x56
|
|
#define CONFIG_RTC_RV3029
|
|
/* Enable 5k Ohm trickle charge resistor */
|
|
#define CONFIG_SYS_RV3029_TCR 0x20
|
|
#else
|
|
#define CONFIG_RTC_DS1337
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */
|
|
#endif
|
|
|
|
/*
|
|
* Flash configuration
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI 1
|
|
#define CONFIG_FLASH_CFI_DRIVER 1
|
|
|
|
#if defined(CONFIG_DIGSY_REV5)
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000
|
|
#define CONFIG_SYS_FLASH_BASE_CS1 0xFC000000
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
|
|
CONFIG_SYS_FLASH_BASE_CS1}
|
|
#define CONFIG_SYS_UPDATE_FLASH_SIZE
|
|
#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
|
|
#else
|
|
#define CONFIG_SYS_FLASH_BASE 0xFF000000
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256
|
|
#define CONFIG_FLASH_16BIT
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
#define CONFIG_SYS_FLASH_SIZE 0x01000000
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500
|
|
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
|
|
#define OF_CPU "PowerPC,5200@0"
|
|
#define OF_SOC "soc5200@f0000000"
|
|
#define OF_TBCLK (bd->bi_busfreq / 4)
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_R
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* Environment settings
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#if defined(CONFIG_LOWBOOT)
|
|
#define CONFIG_ENV_ADDR 0xFF060000
|
|
#else /* CONFIG_LOWBOOT */
|
|
#define CONFIG_ENV_ADDR 0xFFF60000
|
|
#endif /* CONFIG_LOWBOOT */
|
|
#define CONFIG_ENV_SIZE 0x10000
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#define CONFIG_ENV_OVERWRITE 1
|
|
|
|
/*
|
|
* Memory map
|
|
*/
|
|
#define CONFIG_SYS_MBAR 0xF0000000
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#if !defined(CONFIG_SYS_LOWBOOT)
|
|
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
|
|
#else
|
|
#define CONFIG_SYS_DEFAULT_MBAR 0xF0000000
|
|
#endif
|
|
|
|
/*
|
|
* Use SRAM until RAM will be available
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
|
|
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_RAMBOOT 1
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
|
#define CONFIG_SYS_MALLOC_LEN (4096 << 10)
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
|
|
|
|
/*
|
|
* Ethernet configuration
|
|
*/
|
|
#define CONFIG_MPC5xxx_FEC 1
|
|
#define CONFIG_MPC5xxx_FEC_MII100
|
|
#if defined(CONFIG_DIGSY_REV5)
|
|
#define CONFIG_PHY_ADDR 0x01
|
|
#else
|
|
#define CONFIG_PHY_ADDR 0x00
|
|
#endif
|
|
#define CONFIG_PHY_RESET_DELAY 1000
|
|
|
|
#define CONFIG_NETCONSOLE /* include NetConsole support */
|
|
|
|
/*
|
|
* GPIO configuration
|
|
* use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1)
|
|
* Bit 0 (mask 0x80000000) : 0x1
|
|
* SPI on Tmr2/3/4/5 pins
|
|
* Bit 2:3 (mask 0x30000000) : 0x2
|
|
* ATA cs0/1 on csb_4/5
|
|
* Bit 6:7 (mask 0x03000000) : 0x2
|
|
* Ethernet 100Mbit with MD
|
|
* Bits 12:15 (mask 0x000f0000): 0x5
|
|
* USB - Two UARTs
|
|
* Bits 18:19 (mask 0x00003000) : 0x2
|
|
* PSC3 - USB2 on PSC3
|
|
* Bits 20:23 (mask 0x00000f00) : 0x1
|
|
* PSC2 - CAN1&2 on PSC2 pins
|
|
* Bits 25:27 (mask 0x00000070) : 0x1
|
|
* PSC1 - AC97 functionality
|
|
* Bits 29:31 (mask 0x00000007) : 0x2
|
|
*/
|
|
#define CONFIG_SYS_GPS_PORT_CONFIG 0xA2552112
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
#define CONFIG_CMDLINE_EDITING 1
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
|
|
#define CONFIG_LOOPW 1
|
|
#define CONFIG_MX_CYCLIC 1
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK
|
|
|
|
#define CONFIG_SYS_CBSIZE 1024
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
|
|
#define CONFIG_SYS_MAXARGS 32
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
|
#define CONFIG_SYS_MEMTEST_SCRATCH 0x00001000
|
|
#define CONFIG_SYS_MEMTEST_START 0x00010000
|
|
#define CONFIG_SYS_MEMTEST_END 0x019fffff
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x00100000
|
|
|
|
/*
|
|
* Various low-level settings
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_CS1 1
|
|
#define CONFIG_SYS_XLB_PIPELINING 1
|
|
|
|
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
|
|
#define CONFIG_SYS_HID0_FINAL HID0_ICE
|
|
|
|
#if defined(CONFIG_SYS_LOWBOOT)
|
|
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#define CONFIG_SYS_BOOTCS_CFG 0x0002DD00
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CS4_START 0x60000000
|
|
#define CONFIG_SYS_CS4_SIZE 0x1000
|
|
#define CONFIG_SYS_CS4_CFG 0x0008FC00
|
|
|
|
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#define CONFIG_SYS_CS0_CFG 0x0002DD00
|
|
|
|
#if defined(CONFIG_DIGSY_REV5)
|
|
#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE_CS1
|
|
#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#define CONFIG_SYS_CS1_CFG 0x0002DD00
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CS_BURST 0x00000000
|
|
#define CONFIG_SYS_CS_DEADCYCLE 0x11111111
|
|
|
|
#if !defined(CONFIG_SYS_LOWBOOT)
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
|
|
#else
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xff000100
|
|
#endif
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#define CONFIG_USB_OHCI_NEW
|
|
#define CONFIG_SYS_OHCI_BE_CONTROLLER
|
|
#define CONFIG_USB_STORAGE
|
|
|
|
#define CONFIG_USB_CLOCK 0x00013333
|
|
#define CONFIG_USB_CONFIG 0x00002000
|
|
|
|
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
|
|
#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB
|
|
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200"
|
|
#define CONFIG_SYS_USB_OHCI_CPU_INIT
|
|
|
|
/*
|
|
* IDE/ATA
|
|
*/
|
|
#define CONFIG_IDE_RESET
|
|
#define CONFIG_IDE_PREINIT
|
|
|
|
#define CONFIG_SYS_ATA_CS_ON_I2C2
|
|
#define CONFIG_SYS_IDE_MAXBUS 1
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
|
|
#define CONFIG_SYS_ATA_STRIDE 4
|
|
|
|
#define CONFIG_ATAPI 1
|
|
#define CONFIG_LBA48 1
|
|
|
|
#endif /* __CONFIG_H */
|