mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 23:47:24 +00:00
34b080b79c
UHS-I support is available on Ventana boards with micro-SD sockets depending on the board revision. For backwards compatibility to not break users who have old bootloaders and newer kernels the device-tree on boards with microSD disables UHS-I support by default by defining the no-1-8-v property in the esdhc controller node. For models/revisions that support switchable 1.8V/3.3V I/O which is detectable by the presence of a pull-down on the SD3_VSELECT pin we remove that property to enable support in the kernel. Additionally we add SD3_VSELECT to the pinmux for clarity (even though U-Boot does not currently support UHS-I modes requiring 1.8V I/O). Signed-off-by: Tim Harvey <tharvey@gateworks.com>
97 lines
2.5 KiB
C
97 lines
2.5 KiB
C
/*
|
|
* Copyright (C) 2013 Gateworks Corporation
|
|
*
|
|
* Author: Tim Harvey <tharvey@gateworks.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef _GWVENTANA_COMMON_H_
|
|
#define _GWVENTANA_COMMON_H_
|
|
|
|
#include "ventana_eeprom.h"
|
|
|
|
/* GPIO's common to all baseboards */
|
|
#define GP_PHY_RST IMX_GPIO_NR(1, 30)
|
|
#define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22)
|
|
#define GP_SD3_CD IMX_GPIO_NR(7, 0)
|
|
#define GP_RS232_EN IMX_GPIO_NR(2, 11)
|
|
#define GP_MSATA_SEL IMX_GPIO_NR(2, 8)
|
|
#define GP_SD3_VSELECT IMX_GPIO_NR(6, 14)
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
|
|
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define SPI_PAD_CTRL (PAD_CTL_HYS | \
|
|
PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
|
|
|
|
#define IRQ_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
|
|
|
|
#define DIO_PAD_CFG (MUX_PAD_CTRL(IRQ_PAD_CTRL) | MUX_MODE_SION)
|
|
|
|
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
|
|
/*
|
|
* each baseboard has 4 user configurable Digital IO lines which can
|
|
* be pinmuxed as a GPIO or in some cases a PWM
|
|
*/
|
|
struct dio_cfg {
|
|
iomux_v3_cfg_t gpio_padmux[2];
|
|
unsigned gpio_param;
|
|
iomux_v3_cfg_t pwm_padmux[2];
|
|
unsigned pwm_param;
|
|
};
|
|
|
|
struct ventana {
|
|
/* pinmux */
|
|
iomux_v3_cfg_t const *gpio_pads;
|
|
int num_pads;
|
|
/* DIO pinmux/val */
|
|
struct dio_cfg dio_cfg[4];
|
|
int num_gpios;
|
|
/* various gpios (0 if non-existent) */
|
|
int leds[3];
|
|
int pcie_rst;
|
|
int mezz_pwren;
|
|
int mezz_irq;
|
|
int rs485en;
|
|
int gps_shdn;
|
|
int vidin_en;
|
|
int dioi2c_en;
|
|
int pcie_sson;
|
|
int usb_sel;
|
|
int wdis;
|
|
int msata_en;
|
|
bool usd_vsel;
|
|
};
|
|
|
|
extern struct ventana gpio_cfg[GW_UNKNOWN];
|
|
|
|
/* configure i2c iomux */
|
|
void setup_ventana_i2c(void);
|
|
/* configure uart iomux */
|
|
void setup_iomux_uart(void);
|
|
/* conifgure PMIC */
|
|
void setup_pmic(void);
|
|
/* configure gpio iomux/defaults */
|
|
void setup_iomux_gpio(int board, struct ventana_board_info *);
|
|
/* late setup of GPIO (configuration per baseboard and env) */
|
|
void setup_board_gpio(int board, struct ventana_board_info *);
|
|
|
|
#endif /* #ifndef _GWVENTANA_COMMON_H_ */
|