mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 06:12:58 +00:00
0459bc30b6
OMAP5432 did go into production with AVS class0 registers which were mutually exclusive from AVS Class 1.5 registers. Most OMAP5-uEVM boards use the pre-production Class1.5 which has production efuse registers set to 0. However on production devices, these are set to valid data. scale_vcore logic is already smart enough to detect this and use the "Nominal voltage" on devices that do not have efuse registers populated. On a test production device populated as follows: MPU OPP_NOM: => md.l 0x04A0021C4 1 4a0021c4: 03a003e9 .... (0x3e9 = 1.01v) vs nom voltage of 1.06v MPU OPP_HIGH: => md.l 0x04A0021C8 1 4a0021c8: 03400485 ..@. MM OPP_NOM: => md.l 0x04A0021A4 1 4a0021a4: 038003d4 .... (0x3d4 = 980mV) vs nom voltage of 1.025v MM OPP_OD: => md.l 0x04A0021A8 1 4a0021a8: 03600403 ..`. CORE OPP_NOM: => md.l 0x04A0021D8 1 4a0021d8: 000003cf .... (0x3cf = 975mV) vs nom voltage of 1.040v Since the efuse values are'nt currently used, we do not regress on existing pre-production samples (they continue to use nominal voltage). But on boards that do have production samples populated, we can leverage the optimal voltages necessary for proper operation. Tested on: a) 720-2644-001 OMAP5UEVM with production sample. b) 750-2628-222(A) UEVM5432G-02 with pre-production sample. Data based on OMAP5432 Technical reference Manual SWPU282AF (May 2012-Revised Aug 2016) NOTE: All collaterals on OMAP5432 silicon itself seems to have been removed from ti.com, though EVM details are still available: http://www.ti.com/tool/OMAP5432-EVM Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
57 lines
1.4 KiB
C
57 lines
1.4 KiB
C
/*
|
|
* Adaptive Body Bias programming sequence for OMAP5 family
|
|
*
|
|
* (C) Copyright 2013
|
|
* Texas Instruments, <www.ti.com>
|
|
*
|
|
* Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/omap_common.h>
|
|
#include <asm/io.h>
|
|
|
|
/*
|
|
* Setup LDOVBB for OMAP5.
|
|
* On OMAP5+ some ABB settings are fused. They are handled
|
|
* in the following way:
|
|
*
|
|
* 1. corresponding EFUSE register contains ABB enable bit
|
|
* and VSET value
|
|
* 2. If ABB enable bit is set to 1, than ABB should be
|
|
* enabled, otherwise ABB should be disabled
|
|
* 3. If ABB is enabled, than VSET value should be copied
|
|
* to corresponding MUX control register
|
|
*/
|
|
s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb)
|
|
{
|
|
u32 vset;
|
|
u32 fuse_enable_mask = OMAP5_PROD_ABB_FUSE_ENABLE_MASK;
|
|
u32 fuse_vset_mask = OMAP5_PROD_ABB_FUSE_VSET_MASK;
|
|
|
|
if (!is_omap54xx()) {
|
|
/* DRA7 */
|
|
fuse_enable_mask = DRA7_ABB_FUSE_ENABLE_MASK;
|
|
fuse_vset_mask = DRA7_ABB_FUSE_VSET_MASK;
|
|
}
|
|
/*
|
|
* ABB parameters must be properly fused
|
|
* otherwise ABB should be disabled
|
|
*/
|
|
vset = readl(fuse);
|
|
if (!(vset & fuse_enable_mask))
|
|
return -1;
|
|
|
|
/* prepare VSET value for LDOVBB mux register */
|
|
vset &= fuse_vset_mask;
|
|
vset >>= ffs(fuse_vset_mask) - 1;
|
|
vset <<= ffs(OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK) - 1;
|
|
vset |= OMAP5_ABB_LDOVBBMPU_MUX_CTRL_MASK;
|
|
|
|
/* setup LDOVBB using fused value */
|
|
clrsetbits_le32(ldovbb, OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK, vset);
|
|
|
|
return 0;
|
|
}
|