mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 09:30:10 +00:00
b5e01eecc8
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH). Adding details for the same. Below is the brief description of DDR3 init sequence(SW leveling): -> Enable VTT regulator -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program leveling registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
58 lines
1.5 KiB
C
58 lines
1.5 KiB
C
/*
|
|
* mux.c
|
|
*
|
|
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mux.h>
|
|
#include "board.h"
|
|
|
|
static struct module_pin_mux uart0_pin_mux[] = {
|
|
{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{OFFSET(uart0_txd), (MODE(0) | PULLUDDIS | PULLUP_EN | SLEWCTRL)},
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux mmc0_pin_mux[] = {
|
|
{OFFSET(mmc0_clk), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* MMC0_CLK */
|
|
{OFFSET(mmc0_cmd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_CMD */
|
|
{OFFSET(mmc0_dat0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT0 */
|
|
{OFFSET(mmc0_dat1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT1 */
|
|
{OFFSET(mmc0_dat2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT2 */
|
|
{OFFSET(mmc0_dat3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* MMC0_DAT3 */
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux i2c0_pin_mux[] = {
|
|
{OFFSET(i2c0_sda), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{OFFSET(i2c0_scl), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)},
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux gpio0_22_pin_mux[] = {
|
|
{OFFSET(ddr_ba2), (MODE(9) | PULLUP_EN)}, /* GPIO0_22 */
|
|
{-1},
|
|
};
|
|
|
|
void enable_uart0_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(uart0_pin_mux);
|
|
}
|
|
|
|
void enable_board_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(mmc0_pin_mux);
|
|
configure_module_pin_mux(i2c0_pin_mux);
|
|
|
|
if (board_is_gpevm())
|
|
configure_module_pin_mux(gpio0_22_pin_mux);
|
|
}
|
|
|
|
void enable_i2c0_pin_mux(void)
|
|
{
|
|
configure_module_pin_mux(i2c0_pin_mux);
|
|
}
|