u-boot/arch/x86/cpu/qemu/pci.c
Bin Meng 9830d2ebb4 x86: qemu: Turn on PCIe ECAM address range decoding on Q35
Turn on PCIe ECAM address range decoding on Q35.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-28 10:36:25 -06:00

138 lines
3.6 KiB
C

/*
* Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <pci.h>
#include <pci_rom.h>
#include <asm/pci.h>
#include <asm/arch/device.h>
#include <asm/arch/qemu.h>
DECLARE_GLOBAL_DATA_PTR;
static bool i440fx;
void board_pci_setup_hose(struct pci_controller *hose)
{
hose->first_busno = 0;
hose->last_busno = 0;
/* PCI memory space */
pci_set_region(hose->regions + 0,
CONFIG_PCI_MEM_BUS,
CONFIG_PCI_MEM_PHYS,
CONFIG_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* PCI IO space */
pci_set_region(hose->regions + 1,
CONFIG_PCI_IO_BUS,
CONFIG_PCI_IO_PHYS,
CONFIG_PCI_IO_SIZE,
PCI_REGION_IO);
pci_set_region(hose->regions + 2,
CONFIG_PCI_PREF_BUS,
CONFIG_PCI_PREF_PHYS,
CONFIG_PCI_PREF_SIZE,
PCI_REGION_PREFETCH);
pci_set_region(hose->regions + 3,
0,
0,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 4;
}
int board_pci_post_scan(struct pci_controller *hose)
{
int ret = 0;
u16 device, xbcs;
int pam, i;
pci_dev_t vga;
ulong start;
/*
* i440FX and Q35 chipset have different PAM register offset, but with
* the same bitfield layout. Here we determine the offset based on its
* PCI device ID.
*/
device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
pam = i440fx ? I440FX_PAM : Q35_PAM;
/*
* Initialize Programmable Attribute Map (PAM) Registers
*
* Configure legacy segments C/D/E/F to system RAM
*/
for (i = 0; i < PAM_NUM; i++)
x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
if (i440fx) {
/*
* Enable legacy IDE I/O ports decode
*
* Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
* However Linux ata_piix driver does sanity check on these two
* registers to see whether legacy ports decode is turned on.
* This is to make Linux ata_piix driver happy.
*/
x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
/* Enable I/O APIC */
xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
xbcs |= APIC_EN;
x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
} else {
/* Configure PCIe ECAM base address */
x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
CONFIG_PCIE_ECAM_BASE | BAR_EN);
}
/*
* QEMU emulated graphic card shows in the PCI configuration space with
* PCI vendor id and device id as an artificial pair 0x1234:0x1111.
* It is on PCI bus 0, function 0, but device number is not consistent
* for the two x86 targets it supports. For i440FX and PIIX chipset
* board, it shows as device 2, while for Q35 and ICH9 chipset board,
* it shows as device 1.
*/
vga = i440fx ? I440FX_VGA : Q35_VGA;
start = get_timer(0);
ret = pci_run_vga_bios(vga, NULL, PCI_ROM_USE_NATIVE);
debug("BIOS ran in %lums\n", get_timer(start));
return ret;
}
#ifdef CONFIG_GENERATE_MP_TABLE
int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
{
u8 irq;
if (i440fx) {
/*
* Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
* connected to I/O APIC INTPIN#16-19. Instead they are routed
* to an irq number controled by the PIRQ routing register.
*/
irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
PCI_INTERRUPT_LINE);
} else {
/*
* ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
* PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
*/
irq = pirq < 8 ? pirq + 16 : pirq + 12;
}
return irq;
}
#endif