mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-21 10:43:06 +00:00
5f16f655cc
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
268 lines
7.5 KiB
Text
268 lines
7.5 KiB
Text
SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
#
|
|
# Copyright (C) 2018 STMicroelectronics - All Rights Reserved
|
|
#
|
|
|
|
U-Boot on STMicroelectronics STM32MP1
|
|
======================================
|
|
|
|
1. Summary
|
|
==========
|
|
This is a quick instruction for setup stm32mp1 boards.
|
|
|
|
2. Supported devices
|
|
====================
|
|
U-Boot supports one STMP32MP1 SoCs: STM32MP157
|
|
|
|
The STM32MP157 is a Cortex-A MPU aimed at various applications.
|
|
It features:
|
|
- Dual core Cortex-A7 application core
|
|
- 2D/3D image composition with GPU
|
|
- Standard memories interface support
|
|
- Standard connectivity, widely inherited from the STM32 MCU family
|
|
- Comprehensive security support
|
|
|
|
Everything is supported in Linux but U-Boot is limited to:
|
|
1. UART
|
|
2. SDCard/MMC controller (SDMMC)
|
|
|
|
And the necessary drivers
|
|
1. I2C
|
|
2. STPMU1
|
|
2. STPMU1 (PMIC and regulator)
|
|
3. Clock, Reset, Sysreset
|
|
4. Fuse
|
|
|
|
Currently the following boards are supported:
|
|
+ stm32mp157c-ev1
|
|
+ stm32mp157c-ed1
|
|
|
|
3. Boot Sequences
|
|
=================
|
|
|
|
BootRom => FSBL in SYSRAM => SSBL in DDR => OS (Linux Kernel)
|
|
|
|
with FSBL = First Stage Bootloader
|
|
SSBL = Second Stage Bootloader
|
|
|
|
One boot configuration is supported:
|
|
|
|
The "Basic" boot chain (defconfig_file : stm32mp15_basic_defconfig)
|
|
BootRom => FSBL = U-Boot SPL => SSBL = U-Boot
|
|
SPL has limited security initialisation
|
|
U-Boot is running in secure mode and provide a secure monitor to the kernel
|
|
with only PSCI support (Power State Coordination Interface defined by ARM)
|
|
|
|
All the STM32MP1 board supported by U-Boot use the same generic board
|
|
stm32mp1 which support all the bootable devices.
|
|
|
|
Each board is configurated only with the associated device tree.
|
|
|
|
4. Device Tree Selection
|
|
========================
|
|
|
|
You need to select the appropriate device tree for your board,
|
|
the supported device trees for stm32mp157 are:
|
|
|
|
+ ev1: eval board with pmic stpmu1 (ev1 = mother board + daughter ed1)
|
|
dts: stm32mp157c-ev1
|
|
|
|
+ ed1: daughter board with pmic stpmu1
|
|
dts: stm32mp157c-ed1
|
|
|
|
5. Build Procedure
|
|
==================
|
|
|
|
1. Install required tools for U-Boot
|
|
|
|
+ install package needed in U-Boot makefile
|
|
(libssl-dev, swig, libpython-dev...)
|
|
+ install ARMv7 toolchain for 32bit Cortex-A (from Linaro,
|
|
from SDK for STM32MP1, or any crosstoolchains from your distribution)
|
|
|
|
2. Set the cross compiler:
|
|
|
|
# export CROSS_COMPILE=/path/to/toolchain/arm-linux-gnueabi-
|
|
(you can use any gcc cross compiler compatible with U-Boot)
|
|
|
|
3. Select the output directory (optional)
|
|
|
|
# export KBUILD_OUTPUT=/path/to/output
|
|
|
|
for example: use one output directory for each configuration
|
|
# export KBUILD_OUTPUT=stm32mp15_basic
|
|
|
|
4. Configure the U-Boot:
|
|
|
|
# make <defconfig_file>
|
|
|
|
- For basic boot mode: "stm32mp15_basic_defconfig"
|
|
|
|
5. Configure the device-tree and build the U-Boot image:
|
|
|
|
# make DEVICE_TREE=<name> all
|
|
|
|
|
|
example:
|
|
basic boot on ev1
|
|
# export KBUILD_OUTPUT=stm32mp15_basic
|
|
# make stm32mp15_basic_defconfig
|
|
# make DEVICE_TREE=stm32mp157c-ev1 all
|
|
|
|
basic boot on ed1
|
|
# export KBUILD_OUTPUT=stm32mp15_basic
|
|
# make stm32mp15_basic_defconfig
|
|
# make DEVICE_TREE=stm32mp157c-ed1 all
|
|
|
|
6. Output files
|
|
|
|
BootRom and TF-A expect binaries with STM32 image header
|
|
SPL expects file with U-Boot uImage header
|
|
|
|
So in the output directory (selected by KBUILD_OUTPUT),
|
|
you can found the needed files:
|
|
|
|
+ FSBL = spl/u-boot-spl.stm32
|
|
+ SSBL = u-boot.img
|
|
|
|
6. Switch Setting for Boot Mode
|
|
===============================
|
|
|
|
You can select the boot mode, on the board ed1 with the switch SW1
|
|
|
|
-----------------------------------
|
|
Boot Mode BOOT2 BOOT1 BOOT0
|
|
-----------------------------------
|
|
Reserved 0 0 0
|
|
NOR 0 0 1
|
|
SD-Card 1 1 1
|
|
SD-Card 1 0 1
|
|
eMMC 0 1 0
|
|
NAND 0 1 1
|
|
Recovery 1 1 0
|
|
Recovery 0 0 0
|
|
|
|
Recovery is a boot from serial link (UART/USB) and it is used with
|
|
STM32CubeProgrammer tool to load executable in RAM and to update the flash
|
|
devices available on the board (NOR/NAND/eMMC/SDCARD).
|
|
The communication between HOST and board is based on
|
|
- for UARTs : the uart protocol used with all MCU STM32
|
|
- for USB : based on USB DFU 1.1 (without the ST extensions used on MCU STM32)
|
|
|
|
7. Prepare an SDCard
|
|
===================
|
|
|
|
The minimal requirements for STMP32MP1 boot up to U-Boot are:
|
|
- GPT partitioning (with gdisk or with sgdisk)
|
|
- 2 fsbl partitions, named fsbl1 and fsbl2, size at least 256KiB
|
|
- one ssbl partition for U-Boot
|
|
|
|
Then the minimal GPT partition is:
|
|
----- ------- --------- -------------
|
|
| Num | Name | Size | Content |
|
|
----- ------- -------- --------------
|
|
| 1 | fsbl1 | 256 KiB | TF-A or SPL |
|
|
| 2 | fsbl2 | 256 KiB | TF-A or SPL |
|
|
| 3 | ssbl | enought | U-Boot |
|
|
| * | - | - | Boot/Rootfs|
|
|
----- ------- --------- -------------
|
|
|
|
(*) add bootable partition for extlinux.conf
|
|
following Generic Distribution
|
|
(doc/README.distro for use)
|
|
|
|
according the used card reader select the block device
|
|
(/dev/sdx or /dev/mmcblk0)
|
|
in the next example I use /dev/mmcblk0
|
|
|
|
for example: with gpt table with 128 entries
|
|
|
|
a) remove previous formatting
|
|
# sgdisk -o /dev/<SDCard dev>
|
|
|
|
b) create minimal image
|
|
# sgdisk --resize-table=128 -a 1 \
|
|
-n 1:34:545 -c 1:fsbl1 \
|
|
-n 2:546:1057 -c 2:fsbl2 \
|
|
-n 3:1058:5153 -c 3:ssbl \
|
|
-p /dev/<SDCard dev>
|
|
|
|
you can add other partitions for kernel
|
|
one partition rootfs for example:
|
|
-n 3:5154: -c 4:rootfs
|
|
|
|
c) copy the FSBL (2 times) and SSBL file on the correct partition.
|
|
in this example in partition 1 to 3
|
|
|
|
for basic boot mode : <SDCard dev> = /dev/mmcblk0
|
|
# dd if=u-boot-spl.stm32 of=/dev/mmcblk0p1
|
|
# dd if=u-boot-spl.stm32 of=/dev/mmcblk0p2
|
|
# dd if=u-boot.img of=/dev/mmcblk0p3
|
|
|
|
To boot from SDCard, select BootPinMode = 1 1 1 and reset.
|
|
|
|
8. Prepare eMMC
|
|
===============
|
|
You can use U-Boot to copy binary in eMMC.
|
|
|
|
In the next example, you need to boot from SDCARD and the images (u-boot-spl.stm32, u-boot.img)
|
|
are presents on SDCARD (mmc 0) in ext4 partition 4 (bootfs).
|
|
|
|
To boot from SDCard, select BootPinMode = 1 1 1 and reset.
|
|
|
|
Then you update the eMMC with the next U-Boot command :
|
|
|
|
a) prepare GPT on eMMC,
|
|
example with 2 partitions, bootfs and roots:
|
|
|
|
# setenv emmc_part "name=ssbl,size=2MiB;name=bootfs,type=linux,bootable,size=64MiB;name=rootfs,type=linux,size=512"
|
|
# gpt write mmc 1 ${emmc_part}
|
|
|
|
b) copy SPL on eMMC on firts boot partition
|
|
(SPL max size is 256kB, with LBA 512, 0x200)
|
|
|
|
# ext4load mmc 0:4 0xC0000000 u-boot-spl.stm32
|
|
# mmc dev 1
|
|
# mmc partconf 1 1 1 1
|
|
# mmc write ${fileaddr} 0 200
|
|
# mmc partconf 1 1 1 0
|
|
|
|
b) copy U-Boot in first GPT partition of eMMC
|
|
|
|
# ext4load mmc 0:4 0xC0000000 u-boot.img
|
|
# mmc dev 1
|
|
# part start mmc 1 1 partstart
|
|
# part size mmc 1 1 partsize
|
|
# mmc write ${fileaddr} ${partstart} ${partsize}
|
|
|
|
To boot from eMMC, select BootPinMode = 0 1 0 and reset.
|
|
|
|
9. MAC Address
|
|
==============
|
|
|
|
Please read doc/README.enetaddr for the implementation guidelines for mac id
|
|
usage. Basically, environment has precedence over board specific storage.
|
|
|
|
Mac id storage and retrieval in stm32mp otp :
|
|
- OTP_57[31:0] = MAC_ADDR[31:0]
|
|
- OTP_58[15:0] = MAC_ADDR[47:32]
|
|
|
|
To program a MAC address on virgin OTP words above, you can use the fuse command
|
|
on bank 0 to access to internal OTP:
|
|
|
|
example to set mac address "12:34:56:78:9a:bc"
|
|
|
|
1- Write OTP
|
|
STM32MP> fuse prog -y 0 57 0x78563412 0x0000bc9a
|
|
|
|
2- Read OTP
|
|
STM32MP> fuse sense 0 57 2
|
|
Sensing bank 0:
|
|
Word 0x00000039: 78563412 0000bc9a
|
|
|
|
3- next REBOOT :
|
|
### Setting environment from OTP MAC address = "12:34:56:78:9a:bc"
|
|
|
|
4 check env update
|
|
STM32MP> print ethaddr
|
|
ethaddr=12:34:56:78:9a:bc
|