mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-06 13:14:27 +00:00
5ebd3df64d
- drop CONFIG_ prefix from kconfig entry - fix small compilation issue with CONFIG_UBI_SILENCE_MSG Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Kyungmin Park <kmpark@infradead.org>
106 lines
4 KiB
Text
106 lines
4 KiB
Text
menu "UBI support"
|
|
|
|
config UBI_SILENCE_MSG
|
|
bool "UBI silence verbose messages"
|
|
default ENV_IS_IN_UBI
|
|
help
|
|
Make the verbose messages from UBI stop printing. This leaves
|
|
warnings and errors enabled.
|
|
|
|
config MTD_UBI
|
|
bool "Enable UBI - Unsorted block images"
|
|
select RBTREE
|
|
select MTD_PARTITIONS
|
|
help
|
|
UBI is a software layer above MTD layer which admits of LVM-like
|
|
logical volumes on top of MTD devices, hides some complexities of
|
|
flash chips like wear and bad blocks and provides some other useful
|
|
capabilities. Please, consult the MTD web site for more details
|
|
(www.linux-mtd.infradead.org).
|
|
|
|
if MTD_UBI
|
|
|
|
config MTD_UBI_WL_THRESHOLD
|
|
int "UBI wear-leveling threshold"
|
|
default 4096
|
|
range 2 65536
|
|
help
|
|
This parameter defines the maximum difference between the highest
|
|
erase counter value and the lowest erase counter value of eraseblocks
|
|
of UBI devices. When this threshold is exceeded, UBI starts performing
|
|
wear leveling by means of moving data from eraseblock with low erase
|
|
counter to eraseblocks with high erase counter.
|
|
|
|
The default value should be OK for SLC NAND flashes, NOR flashes and
|
|
other flashes which have eraseblock life-cycle 100000 or more.
|
|
However, in case of MLC NAND flashes which typically have eraseblock
|
|
life-cycle less than 10000, the threshold should be lessened (e.g.,
|
|
to 128 or 256, although it does not have to be power of 2).
|
|
|
|
config MTD_UBI_BEB_LIMIT
|
|
int "Maximum expected bad eraseblock count per 1024 eraseblocks"
|
|
default 20
|
|
range 0 768
|
|
help
|
|
This option specifies the maximum bad physical eraseblocks UBI
|
|
expects on the MTD device (per 1024 eraseblocks). If the underlying
|
|
flash does not admit of bad eraseblocks (e.g. NOR flash), this value
|
|
is ignored.
|
|
|
|
NAND datasheets often specify the minimum and maximum NVM (Number of
|
|
Valid Blocks) for the flashes' endurance lifetime. The maximum
|
|
expected bad eraseblocks per 1024 eraseblocks then can be calculated
|
|
as "1024 * (1 - MinNVB / MaxNVB)", which gives 20 for most NANDs
|
|
(MaxNVB is basically the total count of eraseblocks on the chip).
|
|
|
|
To put it differently, if this value is 20, UBI will try to reserve
|
|
about 1.9% of physical eraseblocks for bad blocks handling. And that
|
|
will be 1.9% of eraseblocks on the entire NAND chip, not just the MTD
|
|
partition UBI attaches. This means that if you have, say, a NAND
|
|
flash chip admits maximum 40 bad eraseblocks, and it is split on two
|
|
MTD partitions of the same size, UBI will reserve 40 eraseblocks when
|
|
attaching a partition.
|
|
|
|
This option can be overridden by the "mtd=" UBI module parameter or
|
|
by the "attach" ioctl.
|
|
|
|
Leave the default value if unsure.
|
|
|
|
config MTD_UBI_FASTMAP
|
|
bool "UBI Fastmap (Experimental feature)"
|
|
default n
|
|
help
|
|
Important: this feature is experimental so far and the on-flash
|
|
format for fastmap may change in the next kernel versions
|
|
|
|
Fastmap is a mechanism which allows attaching an UBI device
|
|
in nearly constant time. Instead of scanning the whole MTD device it
|
|
only has to locate a checkpoint (called fastmap) on the device.
|
|
The on-flash fastmap contains all information needed to attach
|
|
the device. Using fastmap makes only sense on large devices where
|
|
attaching by scanning takes long. UBI will not automatically install
|
|
a fastmap on old images, but you can set the UBI module parameter
|
|
fm_autoconvert to 1 if you want so. Please note that fastmap-enabled
|
|
images are still usable with UBI implementations without
|
|
fastmap support. On typical flash devices the whole fastmap fits
|
|
into one PEB. UBI will reserve PEBs to hold two fastmaps.
|
|
|
|
If in doubt, say "N".
|
|
|
|
config MTD_UBI_FASTMAP_AUTOCONVERT
|
|
int "enable UBI Fastmap autoconvert"
|
|
depends on MTD_UBI_FASTMAP
|
|
default 0
|
|
help
|
|
Set this parameter to enable fastmap automatically on images
|
|
without a fastmap.
|
|
|
|
config MTD_UBI_FM_DEBUG
|
|
int "Enable UBI fastmap debug"
|
|
depends on MTD_UBI_FASTMAP
|
|
default 0
|
|
help
|
|
Enable UBI fastmap debug
|
|
|
|
endif # MTD_UBI
|
|
endmenu # "Enable UBI - Unsorted block images"
|