u-boot/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
Stefan Roese cae9008f69 arm: mvebu: Change network init code to allow a more flexible setup
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.

Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-05 14:31:49 +02:00

121 lines
3.1 KiB
C

/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <miiphy.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
DECLARE_GLOBAL_DATA_PTR;
#define BIT(nr) (1UL << (nr))
#define ETH_PHY_CTRL_REG 0
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
/*
* Those values and defines are taken from the Marvell U-Boot version
* "u-boot-2011.12-2014_T1.0" for the board rd78460gp aka
* "RD-AXP-GP rev 1.0".
*
* GPPs
* MPP# NAME IN/OUT
* ----------------------------------------------
* 21 SW_Reset_ OUT
* 25 Phy_Int# IN
* 28 SDI_WP IN
* 29 SDI_Status IN
* 54-61 On GPP Connector ?
* 62 Switch Interrupt IN
* 63-65 Reserved from SW Board ?
* 66 SW_BRD connected IN
*/
#define RD_78460_GP_GPP_OUT_ENA_LOW (~(BIT(21) | BIT(20)))
#define RD_78460_GP_GPP_OUT_ENA_MID (~(BIT(26) | BIT(27)))
#define RD_78460_GP_GPP_OUT_ENA_HIGH (~(0x0))
#define RD_78460_GP_GPP_OUT_VAL_LOW (BIT(21) | BIT(20))
#define RD_78460_GP_GPP_OUT_VAL_MID (BIT(26) | BIT(27))
#define RD_78460_GP_GPP_OUT_VAL_HIGH 0x0
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x00000000, MVEBU_MPP_BASE + 0x00);
writel(0x00000000, MVEBU_MPP_BASE + 0x04);
writel(0x33000000, MVEBU_MPP_BASE + 0x08);
writel(0x11000000, MVEBU_MPP_BASE + 0x0c);
writel(0x11111111, MVEBU_MPP_BASE + 0x10);
writel(0x00221100, MVEBU_MPP_BASE + 0x14);
writel(0x00000003, MVEBU_MPP_BASE + 0x18);
writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
writel(0x00000000, MVEBU_MPP_BASE + 0x20);
/* Configure GPIO */
writel(RD_78460_GP_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
writel(RD_78460_GP_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
writel(RD_78460_GP_GPP_OUT_VAL_HIGH, MVEBU_GPIO2_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_HIGH, MVEBU_GPIO2_BASE + 0x04);
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
return 0;
}
int checkboard(void)
{
puts("Board: Marvell DB-MV784MP-GP\n");
return 0;
}
#ifdef CONFIG_RESET_PHY_R
/* Configure and enable MV88E1545 PHY */
void reset_phy(void)
{
u8 phy_addr[] = CONFIG_PHY_ADDR;
u16 devadr = phy_addr[0];
char *name = "neta0";
u16 reg;
if (miiphy_set_current_dev(name))
return;
/* Enable QSGMII AN */
/* Set page to 4 */
miiphy_write(name, devadr, 0x16, 4);
/* Enable AN */
miiphy_write(name, devadr, 0x0, 0x1140);
/* Set page to 0 */
miiphy_write(name, devadr, 0x16, 0);
/* Phy C_ANEG */
miiphy_read(name, devadr, 0x4, &reg);
reg |= 0x1E0;
miiphy_write(name, devadr, 0x4, reg);
/* Soft-Reset */
miiphy_write(name, devadr, 22, 0x0000);
miiphy_write(name, devadr, 0, 0x9140);
/* Power up the phy */
miiphy_read(name, devadr, ETH_PHY_CTRL_REG, &reg);
reg &= ~(ETH_PHY_CTRL_POWER_DOWN_MASK);
miiphy_write(name, devadr, ETH_PHY_CTRL_REG, reg);
printf("88E1545 Initialized on %s\n", name);
}
#endif /* CONFIG_RESET_PHY_R */