mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-27 15:12:21 +00:00
875143f324
If for some reason DMA module fails to reset user oserves only this: --->--- # dhcp Trying dwmac.e0018000 FAIL --->--- This message makes not much sense. With proposed change error message will be more helpful: --->--- # dhcp Trying dwmac.e0018000 DMA reset timeout FAIL --->--- For example user may do power toggle to recover board functionality. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
460 lines
12 KiB
C
460 lines
12 KiB
C
/*
|
|
* (C) Copyright 2010
|
|
* Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* Designware ethernet IP driver for u-boot
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <malloc.h>
|
|
#include <linux/compiler.h>
|
|
#include <linux/err.h>
|
|
#include <asm/io.h>
|
|
#include "designware.h"
|
|
|
|
#if !defined(CONFIG_PHYLIB)
|
|
# error "DesignWare Ether MAC requires PHYLIB - missing CONFIG_PHYLIB"
|
|
#endif
|
|
|
|
static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
|
|
{
|
|
struct eth_mac_regs *mac_p = bus->priv;
|
|
ulong start;
|
|
u16 miiaddr;
|
|
int timeout = CONFIG_MDIO_TIMEOUT;
|
|
|
|
miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
|
|
((reg << MIIREGSHIFT) & MII_REGMSK);
|
|
|
|
writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
|
|
|
|
start = get_timer(0);
|
|
while (get_timer(start) < timeout) {
|
|
if (!(readl(&mac_p->miiaddr) & MII_BUSY))
|
|
return readl(&mac_p->miidata);
|
|
udelay(10);
|
|
};
|
|
|
|
return -1;
|
|
}
|
|
|
|
static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
|
|
u16 val)
|
|
{
|
|
struct eth_mac_regs *mac_p = bus->priv;
|
|
ulong start;
|
|
u16 miiaddr;
|
|
int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
|
|
|
|
writel(val, &mac_p->miidata);
|
|
miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
|
|
((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
|
|
|
|
writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
|
|
|
|
start = get_timer(0);
|
|
while (get_timer(start) < timeout) {
|
|
if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
|
|
ret = 0;
|
|
break;
|
|
}
|
|
udelay(10);
|
|
};
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dw_mdio_init(char *name, struct eth_mac_regs *mac_regs_p)
|
|
{
|
|
struct mii_dev *bus = mdio_alloc();
|
|
|
|
if (!bus) {
|
|
printf("Failed to allocate MDIO bus\n");
|
|
return -1;
|
|
}
|
|
|
|
bus->read = dw_mdio_read;
|
|
bus->write = dw_mdio_write;
|
|
sprintf(bus->name, name);
|
|
|
|
bus->priv = (void *)mac_regs_p;
|
|
|
|
return mdio_register(bus);
|
|
}
|
|
|
|
static void tx_descs_init(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_dma_regs *dma_p = priv->dma_regs_p;
|
|
struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0];
|
|
char *txbuffs = &priv->txbuffs[0];
|
|
struct dmamacdescr *desc_p;
|
|
u32 idx;
|
|
|
|
for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) {
|
|
desc_p = &desc_table_p[idx];
|
|
desc_p->dmamac_addr = &txbuffs[idx * CONFIG_ETH_BUFSIZE];
|
|
desc_p->dmamac_next = &desc_table_p[idx + 1];
|
|
|
|
#if defined(CONFIG_DW_ALTDESCRIPTOR)
|
|
desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST |
|
|
DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS | \
|
|
DESC_TXSTS_TXCHECKINSCTRL | \
|
|
DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS);
|
|
|
|
desc_p->txrx_status |= DESC_TXSTS_TXCHAIN;
|
|
desc_p->dmamac_cntl = 0;
|
|
desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA);
|
|
#else
|
|
desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN;
|
|
desc_p->txrx_status = 0;
|
|
#endif
|
|
}
|
|
|
|
/* Correcting the last pointer of the chain */
|
|
desc_p->dmamac_next = &desc_table_p[0];
|
|
|
|
/* Flush all Tx buffer descriptors at once */
|
|
flush_dcache_range((unsigned int)priv->tx_mac_descrtable,
|
|
(unsigned int)priv->tx_mac_descrtable +
|
|
sizeof(priv->tx_mac_descrtable));
|
|
|
|
writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr);
|
|
priv->tx_currdescnum = 0;
|
|
}
|
|
|
|
static void rx_descs_init(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_dma_regs *dma_p = priv->dma_regs_p;
|
|
struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0];
|
|
char *rxbuffs = &priv->rxbuffs[0];
|
|
struct dmamacdescr *desc_p;
|
|
u32 idx;
|
|
|
|
/* Before passing buffers to GMAC we need to make sure zeros
|
|
* written there right after "priv" structure allocation were
|
|
* flushed into RAM.
|
|
* Otherwise there's a chance to get some of them flushed in RAM when
|
|
* GMAC is already pushing data to RAM via DMA. This way incoming from
|
|
* GMAC data will be corrupted. */
|
|
flush_dcache_range((unsigned int)rxbuffs, (unsigned int)rxbuffs +
|
|
RX_TOTAL_BUFSIZE);
|
|
|
|
for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) {
|
|
desc_p = &desc_table_p[idx];
|
|
desc_p->dmamac_addr = &rxbuffs[idx * CONFIG_ETH_BUFSIZE];
|
|
desc_p->dmamac_next = &desc_table_p[idx + 1];
|
|
|
|
desc_p->dmamac_cntl =
|
|
(MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) | \
|
|
DESC_RXCTRL_RXCHAIN;
|
|
|
|
desc_p->txrx_status = DESC_RXSTS_OWNBYDMA;
|
|
}
|
|
|
|
/* Correcting the last pointer of the chain */
|
|
desc_p->dmamac_next = &desc_table_p[0];
|
|
|
|
/* Flush all Rx buffer descriptors at once */
|
|
flush_dcache_range((unsigned int)priv->rx_mac_descrtable,
|
|
(unsigned int)priv->rx_mac_descrtable +
|
|
sizeof(priv->rx_mac_descrtable));
|
|
|
|
writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr);
|
|
priv->rx_currdescnum = 0;
|
|
}
|
|
|
|
static int dw_write_hwaddr(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_mac_regs *mac_p = priv->mac_regs_p;
|
|
u32 macid_lo, macid_hi;
|
|
u8 *mac_id = &dev->enetaddr[0];
|
|
|
|
macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
|
|
(mac_id[3] << 24);
|
|
macid_hi = mac_id[4] + (mac_id[5] << 8);
|
|
|
|
writel(macid_hi, &mac_p->macaddr0hi);
|
|
writel(macid_lo, &mac_p->macaddr0lo);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void dw_adjust_link(struct eth_mac_regs *mac_p,
|
|
struct phy_device *phydev)
|
|
{
|
|
u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN;
|
|
|
|
if (!phydev->link) {
|
|
printf("%s: No link.\n", phydev->dev->name);
|
|
return;
|
|
}
|
|
|
|
if (phydev->speed != 1000)
|
|
conf |= MII_PORTSELECT;
|
|
|
|
if (phydev->speed == 100)
|
|
conf |= FES_100;
|
|
|
|
if (phydev->duplex)
|
|
conf |= FULLDPLXMODE;
|
|
|
|
writel(conf, &mac_p->conf);
|
|
|
|
printf("Speed: %d, %s duplex%s\n", phydev->speed,
|
|
(phydev->duplex) ? "full" : "half",
|
|
(phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
|
|
}
|
|
|
|
static void dw_eth_halt(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_mac_regs *mac_p = priv->mac_regs_p;
|
|
struct eth_dma_regs *dma_p = priv->dma_regs_p;
|
|
|
|
writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf);
|
|
writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode);
|
|
|
|
phy_shutdown(priv->phydev);
|
|
}
|
|
|
|
static int dw_eth_init(struct eth_device *dev, bd_t *bis)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_mac_regs *mac_p = priv->mac_regs_p;
|
|
struct eth_dma_regs *dma_p = priv->dma_regs_p;
|
|
unsigned int start;
|
|
|
|
writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
|
|
|
|
start = get_timer(0);
|
|
while (readl(&dma_p->busmode) & DMAMAC_SRST) {
|
|
if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT) {
|
|
printf("DMA reset timeout\n");
|
|
return -1;
|
|
}
|
|
|
|
mdelay(100);
|
|
};
|
|
|
|
/* Soft reset above clears HW address registers.
|
|
* So we have to set it here once again */
|
|
dw_write_hwaddr(dev);
|
|
|
|
rx_descs_init(dev);
|
|
tx_descs_init(dev);
|
|
|
|
writel(FIXEDBURST | PRIORXTX_41 | DMA_PBL, &dma_p->busmode);
|
|
|
|
writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD,
|
|
&dma_p->opmode);
|
|
|
|
writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode);
|
|
|
|
/* Start up the PHY */
|
|
if (phy_startup(priv->phydev)) {
|
|
printf("Could not initialize PHY %s\n",
|
|
priv->phydev->dev->name);
|
|
return -1;
|
|
}
|
|
|
|
dw_adjust_link(mac_p, priv->phydev);
|
|
|
|
if (!priv->phydev->link)
|
|
return -1;
|
|
|
|
writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_eth_send(struct eth_device *dev, void *packet, int length)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct eth_dma_regs *dma_p = priv->dma_regs_p;
|
|
u32 desc_num = priv->tx_currdescnum;
|
|
struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num];
|
|
uint32_t desc_start = (uint32_t)desc_p;
|
|
uint32_t desc_end = desc_start +
|
|
roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN);
|
|
uint32_t data_start = (uint32_t)desc_p->dmamac_addr;
|
|
uint32_t data_end = data_start +
|
|
roundup(length, ARCH_DMA_MINALIGN);
|
|
/*
|
|
* Strictly we only need to invalidate the "txrx_status" field
|
|
* for the following check, but on some platforms we cannot
|
|
* invalidate only 4 bytes, so we flush the entire descriptor,
|
|
* which is 16 bytes in total. This is safe because the
|
|
* individual descriptors in the array are each aligned to
|
|
* ARCH_DMA_MINALIGN and padded appropriately.
|
|
*/
|
|
invalidate_dcache_range(desc_start, desc_end);
|
|
|
|
/* Check if the descriptor is owned by CPU */
|
|
if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) {
|
|
printf("CPU not owner of tx frame\n");
|
|
return -1;
|
|
}
|
|
|
|
memcpy(desc_p->dmamac_addr, packet, length);
|
|
|
|
/* Flush data to be sent */
|
|
flush_dcache_range(data_start, data_end);
|
|
|
|
#if defined(CONFIG_DW_ALTDESCRIPTOR)
|
|
desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST;
|
|
desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) & \
|
|
DESC_TXCTRL_SIZE1MASK;
|
|
|
|
desc_p->txrx_status &= ~(DESC_TXSTS_MSK);
|
|
desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA;
|
|
#else
|
|
desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) & \
|
|
DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST | \
|
|
DESC_TXCTRL_TXFIRST;
|
|
|
|
desc_p->txrx_status = DESC_TXSTS_OWNBYDMA;
|
|
#endif
|
|
|
|
/* Flush modified buffer descriptor */
|
|
flush_dcache_range(desc_start, desc_end);
|
|
|
|
/* Test the wrap-around condition. */
|
|
if (++desc_num >= CONFIG_TX_DESCR_NUM)
|
|
desc_num = 0;
|
|
|
|
priv->tx_currdescnum = desc_num;
|
|
|
|
/* Start the transmission */
|
|
writel(POLL_DATA, &dma_p->txpolldemand);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_eth_recv(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
u32 status, desc_num = priv->rx_currdescnum;
|
|
struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num];
|
|
int length = 0;
|
|
uint32_t desc_start = (uint32_t)desc_p;
|
|
uint32_t desc_end = desc_start +
|
|
roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN);
|
|
uint32_t data_start = (uint32_t)desc_p->dmamac_addr;
|
|
uint32_t data_end;
|
|
|
|
/* Invalidate entire buffer descriptor */
|
|
invalidate_dcache_range(desc_start, desc_end);
|
|
|
|
status = desc_p->txrx_status;
|
|
|
|
/* Check if the owner is the CPU */
|
|
if (!(status & DESC_RXSTS_OWNBYDMA)) {
|
|
|
|
length = (status & DESC_RXSTS_FRMLENMSK) >> \
|
|
DESC_RXSTS_FRMLENSHFT;
|
|
|
|
/* Invalidate received data */
|
|
data_end = data_start + roundup(length, ARCH_DMA_MINALIGN);
|
|
invalidate_dcache_range(data_start, data_end);
|
|
|
|
NetReceive(desc_p->dmamac_addr, length);
|
|
|
|
/*
|
|
* Make the current descriptor valid again and go to
|
|
* the next one
|
|
*/
|
|
desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA;
|
|
|
|
/* Flush only status field - others weren't changed */
|
|
flush_dcache_range(desc_start, desc_end);
|
|
|
|
/* Test the wrap-around condition. */
|
|
if (++desc_num >= CONFIG_RX_DESCR_NUM)
|
|
desc_num = 0;
|
|
}
|
|
|
|
priv->rx_currdescnum = desc_num;
|
|
|
|
return length;
|
|
}
|
|
|
|
static int dw_phy_init(struct eth_device *dev)
|
|
{
|
|
struct dw_eth_dev *priv = dev->priv;
|
|
struct phy_device *phydev;
|
|
int mask = 0xffffffff;
|
|
|
|
#ifdef CONFIG_PHY_ADDR
|
|
mask = 1 << CONFIG_PHY_ADDR;
|
|
#endif
|
|
|
|
phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
|
|
if (!phydev)
|
|
return -1;
|
|
|
|
phy_connect_dev(phydev, dev);
|
|
|
|
phydev->supported &= PHY_GBIT_FEATURES;
|
|
phydev->advertising = phydev->supported;
|
|
|
|
priv->phydev = phydev;
|
|
phy_config(phydev);
|
|
|
|
return 1;
|
|
}
|
|
|
|
int designware_initialize(ulong base_addr, u32 interface)
|
|
{
|
|
struct eth_device *dev;
|
|
struct dw_eth_dev *priv;
|
|
|
|
dev = (struct eth_device *) malloc(sizeof(struct eth_device));
|
|
if (!dev)
|
|
return -ENOMEM;
|
|
|
|
/*
|
|
* Since the priv structure contains the descriptors which need a strict
|
|
* buswidth alignment, memalign is used to allocate memory
|
|
*/
|
|
priv = (struct dw_eth_dev *) memalign(ARCH_DMA_MINALIGN,
|
|
sizeof(struct dw_eth_dev));
|
|
if (!priv) {
|
|
free(dev);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
memset(dev, 0, sizeof(struct eth_device));
|
|
memset(priv, 0, sizeof(struct dw_eth_dev));
|
|
|
|
sprintf(dev->name, "dwmac.%lx", base_addr);
|
|
dev->iobase = (int)base_addr;
|
|
dev->priv = priv;
|
|
|
|
priv->dev = dev;
|
|
priv->mac_regs_p = (struct eth_mac_regs *)base_addr;
|
|
priv->dma_regs_p = (struct eth_dma_regs *)(base_addr +
|
|
DW_DMA_BASE_OFFSET);
|
|
|
|
dev->init = dw_eth_init;
|
|
dev->send = dw_eth_send;
|
|
dev->recv = dw_eth_recv;
|
|
dev->halt = dw_eth_halt;
|
|
dev->write_hwaddr = dw_write_hwaddr;
|
|
|
|
eth_register(dev);
|
|
|
|
priv->interface = interface;
|
|
|
|
dw_mdio_init(dev->name, priv->mac_regs_p);
|
|
priv->bus = miiphy_get_dev_by_name(dev->name);
|
|
|
|
return dw_phy_init(dev);
|
|
}
|