mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 22:03:15 +00:00
c2120fbfbc
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
398 lines
13 KiB
C
398 lines
13 KiB
C
/*
|
|
* (C) Copyright 2000
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
|
|
* U-Boot port on RPXlite board
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define RPXLite_50MHz
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#undef CONFIG_MPC860
|
|
#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
|
|
#define CONFIG_RPXLITE 1
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xfff00000
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#undef CONFIG_8xx_CONS_SMC2
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootp; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#define CONFIG_BZIP2 /* Include support for bzip2 compressed images */
|
|
|
|
/* enable I2C and select the hardware/software driver */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
|
|
#define CONFIG_SYS_I2C_SOFT_SPEED 40000 /* 40 kHz is supposed to work */
|
|
#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
|
|
/* Software (bit-bang) I2C driver configuration */
|
|
#define PB_SCL 0x00000020 /* PB 26 */
|
|
#define PB_SDA 0x00000010 /* PB 27 */
|
|
|
|
#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
|
|
#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
|
|
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
|
|
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
|
|
#define I2C_SDA(bit) if (bit) \
|
|
immr->im_cpm.cp_pbdat |= PB_SDA; \
|
|
else \
|
|
immr->im_cpm.cp_pbdat &= ~PB_SDA
|
|
#define I2C_SCL(bit) if (bit) \
|
|
immr->im_cpm.cp_pbdat |= PB_SCL; \
|
|
else \
|
|
immr->im_cpm.cp_pbdat &= ~PB_SCL
|
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
|
|
/* M41T11 Serial Access Timekeeper(R) SRAM */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
/* play along with the linux driver */
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 1900
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0x09900000
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xFA200000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0xFFC00000
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#ifdef CONFIG_BZIP2
|
|
#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve ~4 MB for malloc() */
|
|
#else
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 KB for malloc() */
|
|
#endif /* CONFIG_BZIP2 */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 19 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_DIRECT_FLASH_TFTP
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_SECT_SIZE 0x40000 /* We use one complete sector */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/*%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_RTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit
|
|
*
|
|
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
|
|
*/
|
|
/* up to 50 MHz we use a 1:1 clock */
|
|
#define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
#define SCCR_MASK SCCR_EBDF00
|
|
/* up to 50 MHz we use a 1:1 clock */
|
|
#define CONFIG_SYS_SCCR (SCCR_COM11 | SCCR_TBS)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCMCIA stuff
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
|
|
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
|
|
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
|
|
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
|
|
|
|
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
/*#define CONFIG_SYS_DER 0x2002000F*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0 and OR0 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
|
|
|
|
/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
|
|
|
|
/*
|
|
* BR1 and OR1 (SDRAM)
|
|
*
|
|
*/
|
|
#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
|
|
#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
|
|
|
|
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
|
|
#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
/* RPXLITE mem setting */
|
|
#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */
|
|
#define CONFIG_SYS_OR3_PRELIM 0xFFFF8910
|
|
#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
|
|
#define CONFIG_SYS_OR4_PRELIM 0xFFFE0970
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*/
|
|
|
|
/* periodic timer for refresh */
|
|
#define CONFIG_SYS_MAMR_PTA 58
|
|
|
|
/*
|
|
* Refresh clock Prescalar
|
|
*/
|
|
#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV8
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 10 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \
|
|
MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
|
|
|
|
/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
|
|
/* Configuration variable added by yooth. */
|
|
/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
|
|
|
|
/*
|
|
* BCSRx
|
|
*
|
|
* Board Status and Control Registers
|
|
*
|
|
*/
|
|
|
|
#define BCSR0 0xFA400000
|
|
#define BCSR1 0xFA400001
|
|
#define BCSR2 0xFA400002
|
|
#define BCSR3 0xFA400003
|
|
|
|
#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
|
|
#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
|
|
#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
|
|
#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
|
|
#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
|
|
#define BCSR0_COLTEST 0x20
|
|
#define BCSR0_ETHLPBK 0x40
|
|
#define BCSR0_ETHEN 0x80
|
|
|
|
#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
|
|
#define BCSR1_PCVCTL6 0x02
|
|
#define BCSR1_PCVCTL5 0x04
|
|
#define BCSR1_PCVCTL4 0x08
|
|
#define BCSR1_IPB5SEL 0x10
|
|
|
|
#define BCSR2_ENPA5HDR 0x08 /* USB Control */
|
|
#define BCSR2_ENUSBCLK 0x10
|
|
#define BCSR2_USBPWREN 0x20
|
|
#define BCSR2_USBSPD 0x40
|
|
#define BCSR2_USBSUSP 0x80
|
|
|
|
#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
|
|
#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
|
|
#define BCSR3_RDY_BSY 0x04 /* Flash Operation */
|
|
#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
|
|
#define BCSR3_D27 0x10 /* Dip Switch settings */
|
|
#define BCSR3_D26 0x20
|
|
#define BCSR3_D25 0x40
|
|
#define BCSR3_D24 0x80
|
|
|
|
#endif /* __CONFIG_H */
|