u-boot/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
Rajeshwari Birje f3d7c2fe9d Exynos5420: Add DDR3 initialization for 5420
This patch intends to add DDR3 initialization code for Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30 16:50:34 +09:00

636 lines
19 KiB
C

/*
* DDR3 mem setup file for board based on EXYNOS5
*
* Copyright (C) 2012 Samsung Electronics
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dmc.h>
#include <asm/arch/power.h>
#include "common_setup.h"
#include "exynos5_setup.h"
#include "clock_init.h"
#define TIMEOUT 10000
#ifdef CONFIG_EXYNOS5250
static void reset_phy_ctrl(void)
{
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
}
int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
int reset)
{
unsigned int val;
struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
struct exynos5_dmc *dmc;
int i;
phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+ DMC_OFFSET);
dmc = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
if (reset)
reset_phy_ctrl();
/* Set Impedance Output Driver */
val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
(mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
(mem->impedance << CA_CS_DRVR_DS_OFFSET) |
(mem->impedance << CA_ADR_DRVR_DS_OFFSET);
writel(val, &phy0_ctrl->phy_con39);
writel(val, &phy1_ctrl->phy_con39);
/* Set Read Latency and Burst Length for PHY0 and PHY1 */
val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
writel(val, &phy0_ctrl->phy_con42);
writel(val, &phy1_ctrl->phy_con42);
/* ZQ Calibration */
if (dmc_config_zq(mem, &phy0_ctrl->phy_con16, &phy1_ctrl->phy_con16,
&phy0_ctrl->phy_con17, &phy1_ctrl->phy_con17))
return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
/* DQ Signal */
writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
| (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
&dmc->concontrol);
update_reset_dll(&dmc->phycontrol0, DDR_MODE_DDR3);
/* DQS Signal */
writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
/* Start DLL locking */
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
&phy0_ctrl->phy_con12);
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
&phy1_ctrl->phy_con12);
update_reset_dll(&dmc->phycontrol0, DDR_MODE_DDR3);
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
&dmc->concontrol);
/* Memory Channel Inteleaving Size */
writel(mem->iv_size, &dmc->ivcontrol);
writel(mem->memconfig, &dmc->memconfig0);
writel(mem->memconfig, &dmc->memconfig1);
writel(mem->membaseconfig0, &dmc->membaseconfig0);
writel(mem->membaseconfig1, &dmc->membaseconfig1);
/* Precharge Configuration */
writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
&dmc->prechconfig);
/* Power Down mode Configuration */
writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
&dmc->pwrdnconfig);
/* TimingRow, TimingData, TimingPower and Timingaref
* values as per Memory AC parameters
*/
writel(mem->timing_ref, &dmc->timingref);
writel(mem->timing_row, &dmc->timingrow);
writel(mem->timing_data, &dmc->timingdata);
writel(mem->timing_power, &dmc->timingpower);
/* Send PALL command */
dmc_config_prech(mem, &dmc->directcmd);
/* Send NOP, MRS and ZQINIT commands */
dmc_config_mrs(mem, &dmc->directcmd);
if (mem->gate_leveling_enable) {
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
writel(val, &phy0_ctrl->phy_con2);
writel(val, &phy1_ctrl->phy_con2);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
val |= RDLVL_GATE_EN;
writel(val, &phy0_ctrl->phy_con2);
writel(val, &phy1_ctrl->phy_con2);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
val |= CTRL_SHGATE;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = PHY_CON1_RESET_VAL;
val &= ~(CTRL_GATEDURADJ_MASK);
writel(val, &phy0_ctrl->phy_con1);
writel(val, &phy1_ctrl->phy_con1);
writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
i = TIMEOUT;
while ((readl(&dmc->phystatus) &
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
/*
* TODO(waihong): Comment on how long this take to
* timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
writel(0, &phy0_ctrl->phy_con14);
writel(0, &phy1_ctrl->phy_con14);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
update_reset_dll(&dmc->phycontrol0, DDR_MODE_DDR3);
}
/* Send PALL command */
dmc_config_prech(mem, &dmc->directcmd);
writel(mem->memcontrol, &dmc->memcontrol);
/* Set DMC Concontrol and enable auto-refresh counter */
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
| (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
return 0;
}
#endif
#ifdef CONFIG_EXYNOS5420
int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
int reset)
{
struct exynos5420_clock *clk =
(struct exynos5420_clock *)samsung_get_base_clock();
struct exynos5420_power *power =
(struct exynos5420_power *)samsung_get_base_power();
struct exynos5420_phy_control *phy0_ctrl, *phy1_ctrl;
struct exynos5420_dmc *drex0, *drex1;
struct exynos5420_tzasc *tzasc0, *tzasc1;
uint32_t val, n_lock_r, n_lock_w_phy0, n_lock_w_phy1;
int chip;
int i;
phy0_ctrl = (struct exynos5420_phy_control *)samsung_get_base_dmc_phy();
phy1_ctrl = (struct exynos5420_phy_control *)(samsung_get_base_dmc_phy()
+ DMC_OFFSET);
drex0 = (struct exynos5420_dmc *)samsung_get_base_dmc_ctrl();
drex1 = (struct exynos5420_dmc *)(samsung_get_base_dmc_ctrl()
+ DMC_OFFSET);
tzasc0 = (struct exynos5420_tzasc *)samsung_get_base_dmc_tzasc();
tzasc1 = (struct exynos5420_tzasc *)(samsung_get_base_dmc_tzasc()
+ DMC_OFFSET);
/* Enable PAUSE for DREX */
setbits_le32(&clk->pause, ENABLE_BIT);
/* Enable BYPASS mode */
setbits_le32(&clk->bpll_con1, BYPASS_EN);
writel(MUX_BPLL_SEL_FOUTBPLL, &clk->src_cdrex);
do {
val = readl(&clk->mux_stat_cdrex);
val &= BPLL_SEL_MASK;
} while (val != FOUTBPLL);
clrbits_le32(&clk->bpll_con1, BYPASS_EN);
/* Specify the DDR memory type as DDR3 */
val = readl(&phy0_ctrl->phy_con0);
val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK << PHY_CON0_CTRL_DDR_MODE_SHIFT);
val |= (DDR_MODE_DDR3 << PHY_CON0_CTRL_DDR_MODE_SHIFT);
writel(val, &phy0_ctrl->phy_con0);
val = readl(&phy1_ctrl->phy_con0);
val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK << PHY_CON0_CTRL_DDR_MODE_SHIFT);
val |= (DDR_MODE_DDR3 << PHY_CON0_CTRL_DDR_MODE_SHIFT);
writel(val, &phy1_ctrl->phy_con0);
/* Set Read Latency and Burst Length for PHY0 and PHY1 */
val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
writel(val, &phy0_ctrl->phy_con42);
writel(val, &phy1_ctrl->phy_con42);
val = readl(&phy0_ctrl->phy_con26);
val &= ~(T_WRDATA_EN_MASK << T_WRDATA_EN_OFFSET);
val |= (T_WRDATA_EN_DDR3 << T_WRDATA_EN_OFFSET);
writel(val, &phy0_ctrl->phy_con26);
val = readl(&phy1_ctrl->phy_con26);
val &= ~(T_WRDATA_EN_MASK << T_WRDATA_EN_OFFSET);
val |= (T_WRDATA_EN_DDR3 << T_WRDATA_EN_OFFSET);
writel(val, &phy1_ctrl->phy_con26);
/*
* Set Driver strength for CK, CKE, CS & CA to 0x7
* Set Driver strength for Data Slice 0~3 to 0x7
*/
val = (0x7 << CA_CK_DRVR_DS_OFFSET) | (0x7 << CA_CKE_DRVR_DS_OFFSET) |
(0x7 << CA_CS_DRVR_DS_OFFSET) | (0x7 << CA_ADR_DRVR_DS_OFFSET);
val |= (0x7 << DA_3_DS_OFFSET) | (0x7 << DA_2_DS_OFFSET) |
(0x7 << DA_1_DS_OFFSET) | (0x7 << DA_0_DS_OFFSET);
writel(val, &phy0_ctrl->phy_con39);
writel(val, &phy1_ctrl->phy_con39);
/* ZQ Calibration */
if (dmc_config_zq(mem, &phy0_ctrl->phy_con16, &phy1_ctrl->phy_con16,
&phy0_ctrl->phy_con17, &phy1_ctrl->phy_con17))
return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
clrbits_le32(&phy0_ctrl->phy_con16, ZQ_CLK_DIV_EN);
clrbits_le32(&phy1_ctrl->phy_con16, ZQ_CLK_DIV_EN);
/* DQ Signal */
val = readl(&phy0_ctrl->phy_con14);
val |= mem->phy0_pulld_dqs;
writel(val, &phy0_ctrl->phy_con14);
val = readl(&phy1_ctrl->phy_con14);
val |= mem->phy1_pulld_dqs;
writel(val, &phy1_ctrl->phy_con14);
val = MEM_TERM_EN | PHY_TERM_EN;
writel(val, &drex0->phycontrol0);
writel(val, &drex1->phycontrol0);
writel(mem->concontrol |
(mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT) |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
&drex0->concontrol);
writel(mem->concontrol |
(mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT) |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
&drex1->concontrol);
do {
val = readl(&drex0->phystatus);
} while ((val & DFI_INIT_COMPLETE) != DFI_INIT_COMPLETE);
do {
val = readl(&drex1->phystatus);
} while ((val & DFI_INIT_COMPLETE) != DFI_INIT_COMPLETE);
clrbits_le32(&drex0->concontrol, DFI_INIT_START);
clrbits_le32(&drex1->concontrol, DFI_INIT_START);
update_reset_dll(&drex0->phycontrol0, DDR_MODE_DDR3);
update_reset_dll(&drex1->phycontrol0, DDR_MODE_DDR3);
/*
* Set Base Address:
* 0x2000_0000 ~ 0x5FFF_FFFF
* 0x6000_0000 ~ 0x9FFF_FFFF
*/
/* MEMBASECONFIG0 */
val = DMC_MEMBASECONFIGX_CHIP_BASE(DMC_CHIP_BASE_0) |
DMC_MEMBASECONFIGX_CHIP_MASK(DMC_CHIP_MASK);
writel(val, &tzasc0->membaseconfig0);
writel(val, &tzasc1->membaseconfig0);
/* MEMBASECONFIG1 */
val = DMC_MEMBASECONFIGX_CHIP_BASE(DMC_CHIP_BASE_1) |
DMC_MEMBASECONFIGX_CHIP_MASK(DMC_CHIP_MASK);
writel(val, &tzasc0->membaseconfig1);
writel(val, &tzasc1->membaseconfig1);
/*
* Memory Channel Inteleaving Size
* Ares Channel interleaving = 128 bytes
*/
/* MEMCONFIG0/1 */
writel(mem->memconfig, &tzasc0->memconfig0);
writel(mem->memconfig, &tzasc1->memconfig0);
writel(mem->memconfig, &tzasc0->memconfig1);
writel(mem->memconfig, &tzasc1->memconfig1);
/* Precharge Configuration */
writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
&drex0->prechconfig0);
writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
&drex1->prechconfig0);
/*
* TimingRow, TimingData, TimingPower and Timingaref
* values as per Memory AC parameters
*/
writel(mem->timing_ref, &drex0->timingref);
writel(mem->timing_ref, &drex1->timingref);
writel(mem->timing_row, &drex0->timingrow0);
writel(mem->timing_row, &drex1->timingrow0);
writel(mem->timing_data, &drex0->timingdata0);
writel(mem->timing_data, &drex1->timingdata0);
writel(mem->timing_power, &drex0->timingpower0);
writel(mem->timing_power, &drex1->timingpower0);
if (reset) {
/*
* Send NOP, MRS and ZQINIT commands
* Sending MRS command will reset the DRAM. We should not be
* reseting the DRAM after resume, this will lead to memory
* corruption as DRAM content is lost after DRAM reset
*/
dmc_config_mrs(mem, &drex0->directcmd);
dmc_config_mrs(mem, &drex1->directcmd);
} else {
/*
* During Suspend-Resume & S/W-Reset, as soon as PMU releases
* pad retention, CKE goes high. This causes memory contents
* not to be retained during DRAM initialization. Therfore,
* there is a new control register(0x100431e8[28]) which lets us
* release pad retention and retain the memory content until the
* initialization is complete.
*/
writel(PAD_RETENTION_DRAM_COREBLK_VAL,
&power->pad_retention_dram_coreblk_option);
do {
val = readl(&power->pad_retention_dram_status);
} while (val != 0x1);
/*
* CKE PAD retention disables DRAM self-refresh mode.
* Send auto refresh command for DRAM refresh.
*/
for (i = 0; i < 128; i++) {
for (chip = 0; chip < mem->chips_to_configure; chip++) {
writel(DIRECT_CMD_REFA |
(chip << DIRECT_CMD_CHIP_SHIFT),
&drex0->directcmd);
writel(DIRECT_CMD_REFA |
(chip << DIRECT_CMD_CHIP_SHIFT),
&drex1->directcmd);
}
}
}
if (mem->gate_leveling_enable) {
writel(PHY_CON0_RESET_VAL, &phy0_ctrl->phy_con0);
writel(PHY_CON0_RESET_VAL, &phy1_ctrl->phy_con0);
setbits_le32(&phy0_ctrl->phy_con0, P0_CMD_EN);
setbits_le32(&phy1_ctrl->phy_con0, P0_CMD_EN);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
writel(val, &phy0_ctrl->phy_con2);
writel(val, &phy1_ctrl->phy_con2);
val = readl(&phy0_ctrl->phy_con1);
val |= (RDLVL_PASS_ADJ_VAL << RDLVL_PASS_ADJ_OFFSET);
writel(val, &phy0_ctrl->phy_con1);
val = readl(&phy1_ctrl->phy_con1);
val |= (RDLVL_PASS_ADJ_VAL << RDLVL_PASS_ADJ_OFFSET);
writel(val, &phy1_ctrl->phy_con1);
n_lock_r = readl(&phy0_ctrl->phy_con13);
n_lock_w_phy0 = (n_lock_r & CTRL_LOCK_COARSE_MASK) >> 2;
n_lock_r = readl(&phy0_ctrl->phy_con12);
n_lock_r &= ~CTRL_DLL_ON;
n_lock_r |= n_lock_w_phy0;
writel(n_lock_r, &phy0_ctrl->phy_con12);
n_lock_r = readl(&phy1_ctrl->phy_con13);
n_lock_w_phy1 = (n_lock_r & CTRL_LOCK_COARSE_MASK) >> 2;
n_lock_r = readl(&phy1_ctrl->phy_con12);
n_lock_r &= ~CTRL_DLL_ON;
n_lock_r |= n_lock_w_phy1;
writel(n_lock_r, &phy1_ctrl->phy_con12);
val = (0x3 << DIRECT_CMD_BANK_SHIFT) | 0x4;
for (chip = 0; chip < mem->chips_to_configure; chip++) {
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex0->directcmd);
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex1->directcmd);
}
setbits_le32(&phy0_ctrl->phy_con2, RDLVL_GATE_EN);
setbits_le32(&phy1_ctrl->phy_con2, RDLVL_GATE_EN);
setbits_le32(&phy0_ctrl->phy_con0, CTRL_SHGATE);
setbits_le32(&phy1_ctrl->phy_con0, CTRL_SHGATE);
val = readl(&phy0_ctrl->phy_con1);
val &= ~(CTRL_GATEDURADJ_MASK);
writel(val, &phy0_ctrl->phy_con1);
val = readl(&phy1_ctrl->phy_con1);
val &= ~(CTRL_GATEDURADJ_MASK);
writel(val, &phy1_ctrl->phy_con1);
writel(CTRL_RDLVL_GATE_ENABLE, &drex0->rdlvl_config);
i = TIMEOUT;
while (((readl(&drex0->phystatus) & RDLVL_COMPLETE_CHO) !=
RDLVL_COMPLETE_CHO) && (i > 0)) {
/*
* TODO(waihong): Comment on how long this take to
* timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
writel(CTRL_RDLVL_GATE_DISABLE, &drex0->rdlvl_config);
writel(CTRL_RDLVL_GATE_ENABLE, &drex1->rdlvl_config);
i = TIMEOUT;
while (((readl(&drex1->phystatus) & RDLVL_COMPLETE_CHO) !=
RDLVL_COMPLETE_CHO) && (i > 0)) {
/*
* TODO(waihong): Comment on how long this take to
* timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
writel(CTRL_RDLVL_GATE_DISABLE, &drex1->rdlvl_config);
writel(0, &phy0_ctrl->phy_con14);
writel(0, &phy1_ctrl->phy_con14);
val = (0x3 << DIRECT_CMD_BANK_SHIFT);
for (chip = 0; chip < mem->chips_to_configure; chip++) {
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex0->directcmd);
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex1->directcmd);
}
if (mem->read_leveling_enable) {
/* Set Read DQ Calibration */
val = (0x3 << DIRECT_CMD_BANK_SHIFT) | 0x4;
for (chip = 0; chip < mem->chips_to_configure; chip++) {
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex0->directcmd);
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex1->directcmd);
}
val = readl(&phy0_ctrl->phy_con1);
val |= READ_LEVELLING_DDR3;
writel(val, &phy0_ctrl->phy_con1);
val = readl(&phy1_ctrl->phy_con1);
val |= READ_LEVELLING_DDR3;
writel(val, &phy1_ctrl->phy_con1);
val = readl(&phy0_ctrl->phy_con2);
val |= (RDLVL_EN | RDLVL_INCR_ADJ);
writel(val, &phy0_ctrl->phy_con2);
val = readl(&phy1_ctrl->phy_con2);
val |= (RDLVL_EN | RDLVL_INCR_ADJ);
writel(val, &phy1_ctrl->phy_con2);
setbits_le32(&drex0->rdlvl_config,
CTRL_RDLVL_DATA_ENABLE);
i = TIMEOUT;
while (((readl(&drex0->phystatus) & RDLVL_COMPLETE_CHO)
!= RDLVL_COMPLETE_CHO) && (i > 0)) {
/*
* TODO(waihong): Comment on how long this take
* to timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
clrbits_le32(&drex0->rdlvl_config,
CTRL_RDLVL_DATA_ENABLE);
setbits_le32(&drex1->rdlvl_config,
CTRL_RDLVL_DATA_ENABLE);
i = TIMEOUT;
while (((readl(&drex1->phystatus) & RDLVL_COMPLETE_CHO)
!= RDLVL_COMPLETE_CHO) && (i > 0)) {
/*
* TODO(waihong): Comment on how long this take
* to timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
clrbits_le32(&drex1->rdlvl_config,
CTRL_RDLVL_DATA_ENABLE);
val = (0x3 << DIRECT_CMD_BANK_SHIFT);
for (chip = 0; chip < mem->chips_to_configure; chip++) {
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex0->directcmd);
writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
&drex1->directcmd);
}
update_reset_dll(&drex0->phycontrol0, DDR_MODE_DDR3);
update_reset_dll(&drex1->phycontrol0, DDR_MODE_DDR3);
}
/* Common Settings for Leveling */
val = PHY_CON12_RESET_VAL;
writel((val + n_lock_w_phy0), &phy0_ctrl->phy_con12);
writel((val + n_lock_w_phy1), &phy1_ctrl->phy_con12);
setbits_le32(&phy0_ctrl->phy_con2, DLL_DESKEW_EN);
setbits_le32(&phy1_ctrl->phy_con2, DLL_DESKEW_EN);
}
/* Send PALL command */
dmc_config_prech(mem, &drex0->directcmd);
dmc_config_prech(mem, &drex1->directcmd);
writel(mem->memcontrol, &drex0->memcontrol);
writel(mem->memcontrol, &drex1->memcontrol);
/*
* Set DMC Concontrol: Enable auto-refresh counter, provide
* read data fetch cycles and enable DREX auto set powerdown
* for input buffer of I/O in none read memory state.
*/
writel(mem->concontrol | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT) |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)|
DMC_CONCONTROL_IO_PD_CON(0x2),
&drex0->concontrol);
writel(mem->concontrol | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT) |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)|
DMC_CONCONTROL_IO_PD_CON(0x2),
&drex1->concontrol);
/*
* Enable Clock Gating Control for DMC
* this saves around 25 mw dmc power as compared to the power
* consumption without these bits enabled
*/
setbits_le32(&drex0->cgcontrol, DMC_INTERNAL_CG);
setbits_le32(&drex1->cgcontrol, DMC_INTERNAL_CG);
return 0;
}
#endif