u-boot/include/configs/s32v234evb.h
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

193 lines
5 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2015-2016 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale S32V234 EVB board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
#define CONFIG_S32V234
/* Config GIC */
#define CONFIG_GICV2
#define GICD_BASE 0x7D001000
#define GICC_BASE 0x7D002000
#define CONFIG_REMAKE_ELF
#undef CONFIG_RUN_FROM_IRAM_ONLY
#define CONFIG_RUN_FROM_DDR1
#undef CONFIG_RUN_FROM_DDR0
/* Run by default from DDR1 */
#ifdef CONFIG_RUN_FROM_DDR0
#define DDR_BASE_ADDR 0x80000000
#else
#define DDR_BASE_ADDR 0xC0000000
#endif
#define CONFIG_MACH_TYPE 4146
#define CONFIG_SKIP_LOWLEVEL_INIT
/* Config CACHE */
#define CONFIG_CMD_CACHE
#define CONFIG_SYS_FULL_VA
/* Enable passing of ATAGs */
#define CONFIG_CMDLINE_TAG
/* SMP Spin Table Definitions */
#define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY (1000000000) /* 1000MHz */
#define CONFIG_SYS_FSL_ERRATUM_A008585
/* Size of malloc() pool */
#ifdef CONFIG_RUN_FROM_IRAM_ONLY
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1 * 1024 * 1024)
#else
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
#endif
#define LINFLEXUART_BASE LINFLEXD0_BASE_ADDR
#define CONFIG_DEBUG_UART_LINFLEXUART
#define CONFIG_DEBUG_UART_BASE LINFLEXUART_BASE
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_UART_PORT (1)
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC_BASE_ADDR
#define CONFIG_SYS_FSL_ESDHC_NUM 1
#define CONFIG_CMD_MMC
/* #define CONFIG_CMD_EXT2 EXT2 Support */
#if 0
/* Ethernet config */
#define CONFIG_CMD_MII
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_FEC_MXC_PHYADDR 0
#endif
#if 0 /* Disable until the FLASH will be implemented */
#define CONFIG_SYS_USE_NAND
#endif
#ifdef CONFIG_SYS_USE_NAND
/* Nand Flash Configs */
#define CONFIG_JFFS2_NAND
#define MTD_NAND_FSL_NFC_SWECC 1
#define CONFIG_NAND_FSL_NFC
#define CONFIG_SYS_NAND_BASE 0x400E0000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
#define CONFIG_SYS_NAND_SELECT_DEVICE
#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#endif
#define CONFIG_LOADADDR 0xC307FFC0
#define CONFIG_EXTRA_ENV_SETTINGS \
"boot_scripts=boot.scr.uimg boot.scr\0" \
"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
"console=ttyLF0,115200\0" \
"fdt_file=s32v234-evb.dtb\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdt_addr_r=0xC2000000\0" \
"kernel_addr_r=0xC307FFC0\0" \
"ramdisk_addr_r=0xC4000000\0" \
"ramdisk=rootfs.uimg\0"\
"ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"update_sd_firmware_filename=u-boot.imx\0" \
"update_sd_firmware=" \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if mmc dev ${mmcdev}; then " \
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
"loadramdisk=fatload mmc ${mmcdev}:${mmcpart} ${ramdisk_addr} ${ramdisk}\0" \
"jtagboot=echo Booting using jtag...; " \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"jtagsdboot=echo Booting loading Linux with ramdisk from SD...; " \
"run loaduimage; run loadramdisk; run loadfdt;"\
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"boot_net_usb_start=true\0" \
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
#define CONFIG_BOOTCOMMAND \
"run distro_bootcmd"
#include <config_distro_bootcmd.h>
/* Miscellaneous configurable options */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "=> "
#define CONFIG_SYS_MEMTEST_START (DDR_BASE_ADDR)
#define CONFIG_SYS_MEMTEST_END (DDR_BASE_ADDR + 0x7C00000)
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
#ifdef CONFIG_RUN_FROM_IRAM_ONLY
#define CONFIG_SYS_MALLOC_BASE (DDR_BASE_ADDR)
#endif
#if 0
/* Configure PXE */
#define CONFIG_BOOTP_PXE_CLIENTARCH 0x100
#endif
/* Physical memory map */
/* EVB board has 2x256 MB DDR chips, DDR0 and DDR1, u-boot is using just one */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM (DDR_BASE_ADDR)
#define PHYS_SDRAM_SIZE (256 * 1024 * 1024)
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* environment organization */
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_OFFSET (12 * 64 * 1024)
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_BOOTP_BOOTFILESIZE
#endif