u-boot/include/configs/phycore_imx8mm.h
Tom Rini 970bf8603b Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_BOOTCOMMAND
   CONFIG_BOOTCOMMAND
   CONFIG_RAMBOOTCOMMAND
   CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01 10:58:10 -05:00

102 lines
3.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0-or-later
*
* Copyright (C) 2019-2020 PHYTEC Messtechnik GmbH
* Author: Teresa Remmet <t.remmet@phytec.de>
*/
#ifndef __PHYCORE_IMX8MM_H
#define __PHYCORE_IMX8MM_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#define CONFIG_SPL_MAX_SIZE (148 * SZ_1K)
#define CONFIG_SYS_MONITOR_LEN SZ_512K
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK 0x920000
#define CONFIG_SPL_BSS_START_ADDR 0x910000
#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR 0x930000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"image=Image\0" \
"console=ttymxc2,115200\0" \
"fdt_addr=0x48000000\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=2\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console} " \
"root=/dev/mmcblk${mmcdev}p${mmcroot} rootwait rw\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if run loadfdt; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;\0 " \
"nfsroot=/nfs\0" \
"netargs=setenv bootargs console=${console} root=/dev/nfs ip=dhcp " \
"nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${loadaddr} ${image}; " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;\0" \
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE SZ_512K
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_MMCROOT "/dev/mmcblk2p2" /* USDHC3 */
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE SZ_2G /* 2GB DDR */
/* UART */
#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE SZ_2K
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* USDHC */
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#endif /* __PHYCORE_IMX8MM_H */